PDA

View Full Version : Rel. 5.00 with only one provider without PIN ?

dadleit
11-02-2002, 15:54
Hi dear Mr Sim_Emu,
It's possible that I can to use Rel. 5.00 for only one provider without use the PIN ?
It's most important for me because I must to clone only one provider inside a sim and I don't want use the pin !
In the silver, I put only one ki and imsi and stop !
Bye
simemu
11-04-2002, 00:04
Yes it is possible, but not at this moment because the SIM-EMU does not allow to disable the PIN.

To allow this, it is necessary to include two GSM commands more.

Regards
dadleit
11-04-2002, 20:58
Hi, SIM_EMU !
I understand that is not possible to disable PIN because there are more providers, but if I want to use only one provider, can you explain to me(only for your kindness !!!) how I can make this ?
Bye
simemu
11-05-2002, 23:27
Here is a rudimentary patch to disable the PIN in SIM-EMU 5.00 and 5.00s, but ...

BE AWARE:
Don't try to enable the PIN again from the mobile menu, because probably you will obtain a Sim Card Error

You must edit the original SIM_EMU_FL_5.00.hex or SEF50sXX.hex with the following changes:
Offset Instead of Put this
0003 30 FF 01 AD
0004 00 AD 30 FF
080E 34 11 34 91
081E 34 11 34 91
The default position at startup will be always the 1st.

Regards
dadleit
11-06-2002, 10:42
Thank you very much !
burakbey
11-19-2002, 12:30
Originally posted by simemu
Here is a rudimentary patch to disable the PIN in SIM-EMU 5.00 and 5.00s, but ...

BE AWARE:
Don't try to enable the PIN again from the mobile menu, because probably you will obtain a Sim Card Error

You must edit the original SIM_EMU_FL_5.00.hex or SEF50sXX.hex with the following changes:
Offset Instead of Put this
0003 30 FF 01 AD
0004 00 AD 30 FF
080E 34 11 34 91
081E 34 11 34 91
The default position at startup will be always the 1st.

Regards

how can i do disable pin2?
simemu
11-19-2002, 18:02
The GSM rules does not allow to disable the PIN2.
jswjm
11-26-2002, 10:17
----------------------------------------------------------------------
Offset Instead of Put this
0003 30 FF 01 AD
0004 00 AD 30 FF
080E 34 11 34 91
081E 34 11 34 91
----------------------------------------------------------------------
I can not search the code£¬can you tell me how to
edit the HEX file?
Eurocrypt
11-26-2002, 14:19
Find these lines
:10000000**********************************
:10101000**********************************
:10103000**********************************

Replace them with these
instead of existing ones in SE 5.00 Flash
:10000000D620A001AE01AD01FF3085008600831629

:10101000003404340034003400340934913404348E

:101030000034043400340034003409349134003472
simemu
11-26-2002, 18:02
Or you can use the ICprog itself to edit these values modifying the referred offset.

Regards
jswjm
11-27-2002, 04:16
Thanks all,I will try it soon. :)
jswjm
11-27-2002, 05:38
HI,SIMEMU

I use the ICprog to load the file SEF50sEN.hex,the address and the program code are shown.I found the the address 0003 or 0004.... are not there!:(
here is the capture file: http://www.shly.net/emu.jpg
What's wrong with me?

Regards
simemu
11-27-2002, 22:36
Each line shows the begin address of that line and continue until the address of the next line - 1.

For example, the first line shows 0000: and the line contains this address and 0001, 0002, ..., 0007.
The second line shows 0008: and the line contains this address and 0009, 000A, 000B, ... , 000F.

Note that the numeric system is hexadecimal.

Resuming, the changes are located in the first line for the first 2 modification.
The third change is located in the line that begins with 0808.
The fourth change is located in the line that begins with 0818.

Regards
Ken-mkII
01-26-2003, 09:14
Great info....

But Mr. SIMEMU:

Would you pls to introudce the modification for Sim EMU 4.10 too?

As it has more phone book & SMS than 5.00 for Silver card....

Thanks...
simemu
01-26-2003, 17:45
Here is a rudimentary patch to disable the PIN in SIM-EMU 4.10, but ...

BE AWARE:
Don't try to enable the PIN again from the mobile menu, because probably you will obtain a Sim Card Error

You must edit the original SIM_EMU_FL_4.10_***.hex with the following changes:

Offset Instead of Put this
0003 30 FF 01 AD
0004 00 AD 30 FF
082C 34 11 34 91
083C 34 11 34 91

The default position at startup will be always the 1st.

Regards
Ken-mkII
01-27-2003, 04:06
Thanks in advance!!
Woron
04-13-2003, 12:07
Dear Simemu,
Is it possible to use this patch for SIM EMU 3.00 as well ?
Or if no, what modification should be done?

With regards