Tahir Riaz
10-26-2008, 10:21
Dear Sir i have a china mobile name is in china and i do not know what but after name 1808 it is dead and take voltage on power supply i try to
format it but failed logs are:
COM6 [VCP0] selected
module v2.65
Device: Autodetect 6228, 6229, 6230 NAND
Checking data, wait...
Action: erase flash chip
Boot...
Press and HOLD Power button now !
baud autodetection active
19200 autodetect
Connecting, wait...
Initializing[6228:8A02:8A02]...
CPU: MT6228
high speed boot enabled
chip: 0031:0000:0101
boot step size: 0400
Release Power button now !
Boot Done
Initialize...
version: 3.0207
loader: 3.748.0
NAND id: ADF1801D
page size: 800+40
pages/block: 40
bits i/o: 08
address cycles: 04
blocks: 0400
ram size: 00800000
NOR: 0000:000000000000 [00000000]
NAND: 00AD:00F10080001D [08400000]
NOR chip is not installed
Initialize Done
Set baud...
115200
Set baud Done
Identification...
reading structure area...
detecting structure...
source data: page only
identification#1 protocol ver: 04
ver. sw1: BXWY28_06B_PCB04_GPRS_MT6228_S02.R888_320_7670_HYN _HY128_V2_1.BIN
ver. sw2: R888_320_7670_Hyn_Hy128_V2.1, 40619D2D
ffs offset/size: 02000000/06000000
id-page1 Ok
nfi area detection finished: Ok
identification#1 structure: 2nd [enhanced] generation
security area (code #1) is Ok
security area (code #1) backup saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_security\i d.27EADFDB.[BXWY28_06B_PCB04_GPRS_MT6228_S02.R888_320_7670_HYN _HY128_V2_1.BIN_D2629EBF].rpl
identification#1 detection finished
Identification Done
Write...
formatting...
................................................er ror: code: 0BCD2D0000
................error: code: F000006900
......................................error: code: A500000000
error: code: 0800000000
its pinout are Rx=3 Tx=10
its soft ver are
v1:BXWY28_06B_PCB04_GPRS_MT6228_S02.R888_320_7670_ HYN_HY128_V2_1.BIN
V2:R888_320_7670_Hyn_Hy128_V2.1, 40619D2D
its chip is 6228
and only accept nand boot
its pics are attached
i download its flash file and flash it but same case before flashing it showed blinking and after flash no blink
i try to format whole flash chip but same log
Plz plz help me to solve this
format it but failed logs are:
COM6 [VCP0] selected
module v2.65
Device: Autodetect 6228, 6229, 6230 NAND
Checking data, wait...
Action: erase flash chip
Boot...
Press and HOLD Power button now !
baud autodetection active
19200 autodetect
Connecting, wait...
Initializing[6228:8A02:8A02]...
CPU: MT6228
high speed boot enabled
chip: 0031:0000:0101
boot step size: 0400
Release Power button now !
Boot Done
Initialize...
version: 3.0207
loader: 3.748.0
NAND id: ADF1801D
page size: 800+40
pages/block: 40
bits i/o: 08
address cycles: 04
blocks: 0400
ram size: 00800000
NOR: 0000:000000000000 [00000000]
NAND: 00AD:00F10080001D [08400000]
NOR chip is not installed
Initialize Done
Set baud...
115200
Set baud Done
Identification...
reading structure area...
detecting structure...
source data: page only
identification#1 protocol ver: 04
ver. sw1: BXWY28_06B_PCB04_GPRS_MT6228_S02.R888_320_7670_HYN _HY128_V2_1.BIN
ver. sw2: R888_320_7670_Hyn_Hy128_V2.1, 40619D2D
ffs offset/size: 02000000/06000000
id-page1 Ok
nfi area detection finished: Ok
identification#1 structure: 2nd [enhanced] generation
security area (code #1) is Ok
security area (code #1) backup saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_security\i d.27EADFDB.[BXWY28_06B_PCB04_GPRS_MT6228_S02.R888_320_7670_HYN _HY128_V2_1.BIN_D2629EBF].rpl
identification#1 detection finished
Identification Done
Write...
formatting...
................................................er ror: code: 0BCD2D0000
................error: code: F000006900
......................................error: code: A500000000
error: code: 0800000000
its pinout are Rx=3 Tx=10
its soft ver are
v1:BXWY28_06B_PCB04_GPRS_MT6228_S02.R888_320_7670_ HYN_HY128_V2_1.BIN
V2:R888_320_7670_Hyn_Hy128_V2.1, 40619D2D
its chip is 6228
and only accept nand boot
its pics are attached
i download its flash file and flash it but same case before flashing it showed blinking and after flash no blink
i try to format whole flash chip but same log
Plz plz help me to solve this