dvd m320 mt6228 any soltion

[BHARGAV]

my mobile shows 10% to 90% then switched off mobile.flashing shows ok bt not working.

COM1 [VCP0] selected
Device: Autodetect 6228, 6229, 6230 NAND
Checking data, wait...
Action: read/check detailed information
Boot...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing[6228:8A02:8A02]...
CPU: MT6228
high speed boot enabled
chip: 0031:0000:0101
boot step size: 0400
Release Power button now !
Boot Done
Initialize...
version: 3.0207
loader: 3.748.0
NAND id: ADF1801D
page size: 800+40
pages/block: 40
bits i/o: 08
address cycles: 04
blocks: 0400
ram size: 00800000
NOR: 0000:000000000000 [00000000]
NAND: 00AD:00F10080001D [08400000]
NOR chip is not installed
Initialize Done
Set baud...
115200
Set baud Done
Identification...
reading structure area...
detecting structure...
source data: page only
identification#1 protocol ver: 04
ver. sw1: M320_PCB04_GPRS_MT6228_S02.M3206V10_07_12_V1_7T13D 080326.BIN
ver. sw2: M3206V10.07.12.V1.7T13D080326, 00000000
ffs offset/size: 02000000/06000000
id-page1 Ok
nfi area detection finished: Ok
identification#1 structure: 2nd [standard] generation
Finished, time used: 72 sec
Remove/Install battery now !

i flashed with this available flash files in spport area


M320_PCB04_GPRS_MT6228_S02.M3206V10_07_12_V1_3T06D 071217_128m_En_Cn.B4M.bin

same problem. any soltion.i read from another working phone but not flashing.


COM1 [VCP0] selected
module v2.65
Device: Autodetect 6228, 6229, 6230 NAND
Checking data, wait...
Action: write NAND flash
read mode: 01
write: Firmware
skip: Customization/Language Pack
skip: Customization
skip: Eeprom/ffs
source data: page only
identification#1 protocol ver: 04
ver. sw1: M320_PCB04_GPRS_MT6228_S02.M3206V10_07_12_V1_3T06D 071217.BIN
ver. sw2: M3206V10.07.12.V1.3T06D071217, 00000000
ffs offset/size: 02000000/06000000
id-page1 Ok
nfi area detection finished: Ok
Boot...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing[6228:8A02:8A02]...
CPU: MT6228
high speed boot enabled
chip: 0031:10AA:0101
boot step size: 0400
Release Power button now !
Boot Done
Initialize...
version: 3.0207
loader: 3.748.0
NAND: Samsung K9F1G08X0M 2048+64 64 pages, 132Mb
NAND id: ECF18015
page size: 800+40
pages/block: 40
bits i/o: 08
address cycles: 04
blocks: 0400
ram size: 00800000
NOR: 0000:000000000000 [00000000]
NAND: 00EC:00F100800015 [08400000]
NOR chip is not installed
Initialize Done
Set baud...
921600
Set baud Done
Identification...
reading structure area...
detecting structure...
source data: page only
identification#1 protocol ver: 04
ver. sw1: M320_PCB04_GPRS_MT6228_S02.M3206V10_07_12_V1_3T06D 071217.BIN
ver. sw2: M3206V10.07.12.V1.3T06D071217, 00000000
ffs offset/size: 02000000/06000000
id-page1 Ok
nfi area detection finished: Ok
identification#1 structure: 2nd [standard] generation
Identification Done
Write...
write core area 1 of 3...
write core area 2 of 3...
write core area 3 of 3...
Write Done
Finished, time used: 400 sec
Remove/Install battery now !


i flased with my working phone readed bin file it shows


COM1 [VCP0] selected
module v2.65
Device: Autodetect 6228, 6229, 6230 NAND
Checking data, wait...
Action: write NAND flash
read mode: 03
write: Firmware
skip: Customization/Language Pack
skip: Customization
skip: Eeprom/ffs
source data: page only
identification#1 protocol ver: 04
ver. sw1: M320_PCB04_GPRS_MT6228_S02.M3206V10_07_12_V1_7T13D 080326.BIN
ver. sw2: M3206V10.07.12.V1.7T13D080326, 00000000
ffs offset/size: 02000000/06000000
id-page1 Ok
warning: size adjusted by end mark [+00020000], probably incorrect/damaged data
nfi area detection finished: Ok
Boot...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing[6228:8A02:8A02]...
CPU: MT6228
high speed boot enabled
chip: 0031:10AA:0101
boot step size: 0400
Release Power button now !
Boot Done
Initialize...
version: 3.0207
loader: 3.748.0
NAND: Samsung K9F1G08X0M 2048+64 64 pages, 132Mb
NAND id: ECF18015
page size: 800+40
pages/block: 40
bits i/o: 08
address cycles: 04
blocks: 0400
ram size: 00800000
NOR: 0000:000000000000 [00000000]
NAND: 00EC:00F100800015 [08400000]
NOR chip is not installed
Initialize Done
Set baud...
921600
Set baud Done
Identification...
reading structure area...
detecting structure...
source data: page only
identification#1 protocol ver: 04
ver. sw1: M320_PCB04_GPRS_MT6228_S02.M3206V10_07_12_V1_7T13D 080326.BIN
ver. sw2: M3206V10.07.12.V1.7T13D080326, 00000000
ffs offset/size: 02000000/06000000
id-page1 Ok
nfi area detection finished: Ok
identification#1 structure: 2nd [standard] generation
Identification Done
Write...
write core area 1 of 3...
write core area 2 of 3...
error: code: A500000BF4
error: code: 5A
error: code: A503740A04
error: code: 03740A0403
error: code: 0000000000
error: code: 0000000000
error: code: 0000000000
error: code: 00000000
error: code:
error: block/offset: 00000CAA/00CAA000
error: can't write nand core
Write Fail
Finished, time used: 324 sec
Remove/Install battery now !

[gs cell]

same problem in 5 sets 90 % & 99% phone off pls fix this prob infinity team

[InfinityHelp]

hello!

in most cases this is hardware fault

[BHARGAV]

it's 100% software problem today i face same problem another dvd also.it is 128mb memory.

http://www.forum.phones-china.com/viewthread.php?tid=8642&highlight=dvd%2Bm320


check this

[BHARGAV]

i have another working set if u want i read flash and send to u


u can solve this problem?(infinity team)

[sharmavnn]

it's 100% software problem today i face same problem another dvd also.it is 128mb memory.

http://www.forum.phones-china.com/viewthread.php?tid=8642&highlight=dvd%2bm320


check this

from this site we could not download that flash file if have the same flash file can u share it in this site.i have a account in the above site.

[InfinitySupport]

i have another working set if u want i read flash and send to u


u can solve this problem?(infinity team)

If you have another good working phone in some cases you can just read flash from it and try to flash other phone.
Let's see results.

[BHARGAV]

after flash mobile restars continue

[InfinitySupport]

after flash mobile restars continue

Did you tried to power-on phone without sim card ?
What is the results ?