JC_BY
10-28-2008, 16:29
COM6 [VCP1] selected
module v2.66
Device: Autodetect 6228, 6229, 6230 NAND
Checking data, wait...
Action: read NAND flash
read mode: 01
Boot...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing[6230:8A02:8A02]...
CPU: MT6230
high speed boot enabled
chip: 0031:000D:0101
boot step size: 0400
Release Power button now !
Boot Done
Initialize...
version: 3.020C
loader: 3.748.0
NAND id: EC795A3F
page size: 200+10
pages/block: 20
bits i/o: 08
address cycles: 04
blocks: 2000
NOR: 0000:000000000000 [00000000]
NAND: 00EC:0079005A003F [08400000]
NOR chip is not installed
Initialize Done
Set baud...
921600
Set baud Done
Identification...
reading structure area...
detecting structure...
source data: page only
identification#1 protocol ver: 04
ver. sw1: UFO318_B_PCB01_GPRS_MT6230_S02.APL219_V1_0_2008091 9.BIN
ver. sw2: APL219_V1.0_20080919, D65A8FAE
ffs offset/size: 02000000/06000000
id-page1 Ok
nfi area detection finished: Ok
identification#1 structure: 2nd [enhanced] generation
security area (code #1) is damaged, recalculation required
identification#1 detection finished
reading...
checking backup data integrity...
source data: page only
identification#1 protocol ver: 04
ver. sw1: UFO318_B_PCB01_GPRS_MT6230_S02.APL219_V1_0_2008091 9.BIN
ver. sw2: APL219_V1.0_20080919, D65A8FAE
ffs offset/size: 02000000/06000000
id-page1 Ok
warning: size adjusted by end mark [+0140D59E], probably incorrect/damaged data
warning: size exceed ffs area, truncated: 01BE0000
nfi area detection finished: Ok
file saved: C:\Program Files\InfinityBox\ChineseMiracle\nand_probably_dam aged_[UFO318_B_PCB01_GPRS_MT6230_S02.APL219_V1_0_2008091 9.BIN]_full_20081028-155942.B4M.bin
Finished, time used: 9996 sec
Remove/Install battery now !
smart-card disconnected
Any solution?
module v2.66
Device: Autodetect 6228, 6229, 6230 NAND
Checking data, wait...
Action: read NAND flash
read mode: 01
Boot...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing[6230:8A02:8A02]...
CPU: MT6230
high speed boot enabled
chip: 0031:000D:0101
boot step size: 0400
Release Power button now !
Boot Done
Initialize...
version: 3.020C
loader: 3.748.0
NAND id: EC795A3F
page size: 200+10
pages/block: 20
bits i/o: 08
address cycles: 04
blocks: 2000
NOR: 0000:000000000000 [00000000]
NAND: 00EC:0079005A003F [08400000]
NOR chip is not installed
Initialize Done
Set baud...
921600
Set baud Done
Identification...
reading structure area...
detecting structure...
source data: page only
identification#1 protocol ver: 04
ver. sw1: UFO318_B_PCB01_GPRS_MT6230_S02.APL219_V1_0_2008091 9.BIN
ver. sw2: APL219_V1.0_20080919, D65A8FAE
ffs offset/size: 02000000/06000000
id-page1 Ok
nfi area detection finished: Ok
identification#1 structure: 2nd [enhanced] generation
security area (code #1) is damaged, recalculation required
identification#1 detection finished
reading...
checking backup data integrity...
source data: page only
identification#1 protocol ver: 04
ver. sw1: UFO318_B_PCB01_GPRS_MT6230_S02.APL219_V1_0_2008091 9.BIN
ver. sw2: APL219_V1.0_20080919, D65A8FAE
ffs offset/size: 02000000/06000000
id-page1 Ok
warning: size adjusted by end mark [+0140D59E], probably incorrect/damaged data
warning: size exceed ffs area, truncated: 01BE0000
nfi area detection finished: Ok
file saved: C:\Program Files\InfinityBox\ChineseMiracle\nand_probably_dam aged_[UFO318_B_PCB01_GPRS_MT6230_S02.APL219_V1_0_2008091 9.BIN]_full_20081028-155942.B4M.bin
Finished, time used: 9996 sec
Remove/Install battery now !
smart-card disconnected
Any solution?