New SIM-EMU 5.00s with Italian menu language

[simemu]

Can be downloaded from my pages.

http://perso.wanadoo.es/djabif
http://simemu.com

The file is SEF50sIT.hex.

The translation was done by Angelo Proietti. Thanks

Regards

[pryngeps]

hi Daniel, I have a small problem, when I try to patch simemu 5.00s in Italian version (SEF50sIT.hex) with your "Sim-Emu 5.00s Configurator" I receive this error message: "Incorrect File Version", why?

tnx pryngeps

[simemu]

You are right. I'd corrected the problem.
Download it again.

Regards

[pryngeps]

thank you very much. great stuff!

pryngeps

[willycutu]

I've got the IT translation but in the menu after the word appear many [] for ie

Configura [][][][]

the [] are square box why this happens?

[simemu]

Your phone is not capable to understand the character hexadecimal 0xFF as end of the literal. Does not follow the rules about this.

But don't worry, edit the SEF50sIT.hex with the ICProg and change the 34FF at the final of each literal with 3420 and write the flash again.
Probably with this change, your phone show literals doing some horizontal scrolling.

Which is your phone ?

Regards

[willycutu]

I'll try it, my phone is the GREAT Nokia 7650
the strange thing is i haven't this problem with 4.10 ITALIAN menu of simemu, why?

[willycutu]

looking inside the .hex i found that, at the end of eache line there is 34FF and if i change it to 340F?

[simemu]

The 4.10 does not have 34FF because the literals are short and cannot be expanded as in 5.00s that has longer literals to allow translation to every language.

I don't know which character corresponds to 340F in your phone. Try it.

Regards

[Mondeo_man]

Hello

Regarding SIM EMMU V5.00s, I have strange problems with this version...I used ENGLISH MENU.

SIM is log to net but if I try to initiate an call I get Sim not registered and is disconnected from net, all IMSI and KI data are correct. This problem is random.

I tested in Nokia 5110, 6150, 3210, 9110 and Motorola v3690...
I tryed 3 different SILVER SIM on all is the same...

It is an SIM SW problem because if I put back 4.10 it is working ok on same Nokia phones.

So my advice wait till next V5.xx is released and use 4.10 this one is OK.

regards
L.

[simemu]

There is no problem with 5.00s, it is exactly as 5.00 and that models works all fine. I have friends with some of those models. ;)

Your problem must be the external EEPROM programming. It's maintaining the 4.10 data. Write again the original SEF50s and SEE50s with the ICProg verification activated.

Regards

[willycutu]

ops, now it works fine with 3420, what i loose or change instead of 34FF?

[simemu]

Read my first response to your question. ;)

Regards

[Mondeo_man]

Thank you for replay,

Now all my Silver cards are programmed with 4.10 and all work fine. So eep data is ok.

If I program only the flash with 5.00s the eep data is safe ? or do I have to reconfigure all the clone sims ?

Best regards
L

[simemu]

You MUST write both files, SEF50s and SEE50s and configure your phones again.

If you must several card with the same data, you can use the Eurocrypt configurator.

Else, you can prepare one and then copy the Flash and EEPROM of this to the rest of your Silvers.

To do this:
1) Write one without the CPD bit activated.
2) Configure all your numbers.
3) Verify that all works fine.
4) Read Flash and EEPROM with ICProg.
5) Write this files in the rest of yur Silvers with CPD activated.
6) Protect the first Silver, writing only the CPD bit. You can do this loading the Flash and Writing the configuration bit.

Regards

[dadleit]

Hi,
what you think about the use CPD if someone put more 3 times wrong PIN ?
This is a most important problem because the counter for the PIN don't work if the fuse CPD is on and this, I think would be dangerous for the owner of the SIM !!!!
For this reason, I have asked you if was possible to use CPD for example from 0000h to 0FF8h.
Bye

[simemu]

You refer to code protection of areas of the Flash, but this is not the CPD.

The CPD is the protection of the internal EEPROM of the PIC where reside the KI's, PIN's and PUK's.

About this, I'd responded you in the post http://forum.gsmhosting.com/vbb/showthread.php?s=&threadid=62459

Regards

[dadleit]

Ok, is true, it's my mistake for language, I know very well the sancript !!!!!
The CP is how say you, but the counter for the PIN is in this area and if I put the CP on from 0000h to 1FFFh, the counter for wrongs PIN don't work.
Bye and excusme

[Mondeo_man]

Thank you for you'r support Simemu:

I programmed an Silver with 5.00 and I'm testing now to see how it's work ( until now is ok no problems like I had with 5.0s ), what I notice:
eep for 5.00 =49063 long
eep for 5.0s =23053
eep for 4.10 =23053

flash file lenght is the same lenght for all versions... the eep lenght is ok ?
If I will upgrade 4.10 or 5.00 to 5.0s eep will be erased complete ?
I am using Dejan interface and his sw for program Silver card and until now I think is OK.

regards
L.

[simemu]

@dadleit
Of course, if you protect an area of the flash, it cannot be modified for the code itself. See Microchip specs.
Don't use the code protection.

@Mondeo_man
DON'T USE 5.00 on the Silvercard
I did the 5.00s for use it in the SilverCards. Look others posts to see the problems that you could have.

The lengths are corrects, the 5.00 EEP has 128kbits (for GreenCard) and the 4.10 and 5.00s EEP has 64Kbits (for SilverCard).

The correct writing of these EP files replace all the previous data.

The flash is the same because the processor of these cards is the same, 16F876/7.

Regards

[Mondeo_man]

Thank you Simemu,

This is happend because I did not read all txt files complete.... sorry.

P.S.
The V.500 still run OK on my Silver...

Regards

[simemu]

@Mondeo_man
Give me how many ADN and SMS have you configurated in the 5.00 in the SilverCard.

Regards

[Mondeo_man]

It is standard, I did not modified anything.
SMS/ADN:40/250
Active nrs:123456

[Saship]

Hi,
I cannot program my Silvercard eeprom with Icprog, can I prgram it with another Program like CardWriter?
And can I use this Soft 5.00s with german providers numbers?
Thanks

[simemu]

@Mondeo_man
Be aware
With that FALSE configuration, (because the Silver has no enough memory for this), when you receive the SMS number 28, all of your IMSI's will be overwritten and you must to reconfigure all the position again.

You decide ...

[Mondeo_man]

Normally I delete old SMS, I also use an 9110 phone... will be an experiment for all.

Thank you again for support.

Best regards
L.