slt100 dead after flash

[mzsufi]

i have unlocked the phone, but it was asking for master code, i decided to flash it then unlock but after flashing the phone is dead, now i can not get it to connect it again, its not powering up again.

this is the log of flash

COM20 [VCP0] selected
module v2.40
Device: Fly-SLT100
Checking data, wait...
Action: write NAND flash
read mode: 01
write: Firmware
skip: Customization/Language Pack
skip: Customization
skip: Eeprom/ffs
source data: page only
identification#1 protocol ver: 04
ver. sw 1: SLT100_HMERID_PCB04_GPRS_MT6228_S02.MAUI_06A_W06_3 6_MP_V36.BIN
ver. sw 2: MAUI.06A.W06.36.MP.V36, 00000000
ffs offset/size: 02000000/02000000
id-page1 Ok
nfi area detection finished: Ok
Boot ...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing [6228:8A02:8A02]...
CPU: MT6228
chip: 0031:0000:0101
boot packet size: 0400
Release Power button now !
Boot Done
Initialize ...
version: 3.0207
loader: 3.748.0
NAND: Hynix HY27XS08121M 512+16 32 pages, 66Mb
NAND id: AD76AD76
page size: 200+10
pages/block: 20
bits i/o: 08
address cycles: 04
blocks: 1000
ram size: 00800000
NOR: 0000:000000000000 [00000000]
NAND: 00AD:007600AD0076 [04200000]
NOR chip is not installed
Initialize Done
Set baud ...
115200
Set baud Done
Identification ...
reading structure area...
detecting structure...
source data: page only
identification#1 protocol ver: 04
ver. sw 1: SLT100_HMERID_PCB04_GPRS_MT6228_S02.MAUI_06A_W06_3 6_MP_V36.BIN
ver. sw 2: MAUI.06A.W06.36.MP.V36, 00000000
ffs offset/size: 02000000/02000000
id-page1 Ok
nfi area detection finished: Ok
identification#1 structure: 2nd [standard] generation
Identification Done
Write ...
write core area 1 of 2...
write core area 2 of 2...
error: code: A500000BF3
error: code:
error: block/offset: 000011B0/011B0000

[InfinitySupport]

Hello,

If phone can not be connected again you need to check battery voltage and charge battery with external power supply.

[mzsufi]

Hello,

If phone can not be connected again you need to check battery voltage and charge battery with external power supply.

i have connected with usb power lead but still not connecting, i will try again with the battry charged

[mzsufi]

Hello,

If phone can not be connected again you need to check battery voltage and charge battery with external power supply.


eaven with battery charged still no connection

pls help as customer can not wait

[luisinhocell]

Look comfortable in using the 3.7vlts

[InfinitySupport]

Hello,

If phone can not be connected you need to check battery voltage and charge battery with external power supply.

[luisinhocell]

But I talked to him in a cell tests the source adjust, and put VLT 3.7 to test the unit ....

[InfinitySupport]

Hello,

Yes. If phone hardware is Ok and battery is enough charged phone can boot in any case, even if flash chip is empty or wrong flashed.

[omer123]

i had this experience last time and buy a new phone to cusomer there definatly somthing wrong infinity support u must do a test on fly slt1oo thanx

[InfinitySupport]

Hello,

It may be the next problem: damaged phone hardware or damaged cable.
There is no any other way why phone can not boot, so I suggest toy yo take your phone (that you have instead of other one), charge battery, double check cable and flash it again now.