6300 rm-217 dead set [Archive]

topnoyze

11-21-2008, 09:42

i recieved 6300 dead set and i tried backing up flashfile but there's no information about the default flashfile on phone...and tried also pressing general info on chinese miracle here's the logs bellow and pls tell me abt it...

br thnks.

COM25 [VCP0] selected
module v2.66
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
eeprom backup enabled, it may takes several minutes !
Action: read/check detailed information
Boot...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing[6226:8A02:8A01]...
CPU: MT6226
high speed boot disabled
chip: 0031:FF8A:6989
high speed disabled
boot step size: 0002
Release Power button now !
Boot Done
Initialize...
detecting chip #00 in region #00...
flash: 98004900000002:2BEA0000000000
flash: Toshiba AMD/Fujitsu std [T 0008x002000 00FFx010000] 16Mb
detecting chip #01 in region #00...
flash: 98004900000002:2BEA0000000000
flash: Toshiba AMD/Fujitsu std [T 0008x002000 00FFx010000] 16Mb
number of flash chip/regions detected: 02/01
Initialize Done
Set baud...
230400
Set baud Done
Initialize bootcode...
Initialize bootcode Done
Check firmware integrity...
device parameters autodetection in progress..
detecting chip #00 in region #00...
flash: 98004900000002:2BEA0000000000
flash: Toshiba AMD/Fujitsu std [T 0008x002000 00FFx010000] 16Mb
detecting chip #01 in region #00...
flash: 98004900000002:2BEA0000000000
flash: Toshiba AMD/Fujitsu std [T 0008x002000 00FFx010000] 16Mb
it's time to stop: 2B0000EA18F09FE118F09FE118F09FE118F09FE118F09FE1
number of flash chip/regions detected: 01/01
total flash region size: 01000000
detect device identification#1...
detection phase #1...
.
detection phase #2...
.................................................. .................................................. ............................
warning: identification#1 information not found, possible reasons:
.old firmware type w/o identification#1 data
.damaged firmware
.damaged hardware
if phone works fine just ignore this warning
detect device identification#1 finished
detect device identification#2...
detection phase #1...
.
warning: optional information is not found,
if phone works well just ignore this warning
detect device identification#2 finished
detecting eeprom/ffs area in 1 chip(s)...
standard eeprom/ffs offset assigned: 00E00000
flash: 98004900000002:2BEA0000000000
checking area[00000000]: 00000000-00FFFFFF...
eeprom/ffs found near: 00E00000
detecting eeprom/ffs size...
eeprom/ffs size: 00200000
ffs chip: 00
eeprom/ffs area: 00000000:00E00000-00FFFFFF
detecting ffs structure pass 1...
.................................................. ......
can't detect fat record name location
ffs element #1 detection failed
detecting ffs structure pass 2...
.................................................. ......
can't detect fat record name location
ffs element #2 detection failed
Check firmware integrity Done
Check firmware content...
Check firmware content Done
Backup required data...
Finished, time used: 171 sec
Remove/Install battery now !

Alfarouk

08-01-2009, 06:15

1. it was turning off
2. I did ffs safe mode format an it was not turning of but no network.
3. I tried flashing with a flashfile I read from another phone of the same type.

here is the log.

Application: C:\Program Files\InfinityBox\ChineseMiracle\ChineseMiracle.ex e
Loading data, wait...
[Infinity Box] v2.73
S/N: 296D:0112
Wait...
Device: Autodetect 6205-6227 NOR
Done
Loading file v.02...
flash[K300_PCB01_GPRS_MT6225_S00.MT6225_GEMINI_V1_00.BIN]_20090718-144041.B0M.bin loaded
identification#1 protocol ver: 04
ver. sw 1: K300_PCB01_GPRS_MT6225_S00.MT6225_GEMINI_V1_00.BIN
ver. sw 2: MT6225_GEMINI_V1.00, 00000000

==== log: [7/29/2009 1:27:55 PM] ====
COM10 [VCP0] selected
module v2.73
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
Action: write NOR flash
"smart write" active
write: Firmware
skip: Customization/Language Pack
skip: Customization
skip: Eeprom/ffs
eeprom backup enabled, it may takes several minutes !
Boot ...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing [6225:8A05:8A00]...
CPU: MT6225
high speed boot On
chip: 0001:7F03:0008
boot packet size: 0400
Release Power button now !
Boot Done
Initialize ...
detecting chip #00 in region #00...
flash: 98000300000001:18E59F00000000
flash: AMD/Fujitsu std [T 0008x004000 007Fx020000] 16Mb
detecting chip #01 in region #00...
flash: 98000300000001:18E59F00000000
flash: AMD/Fujitsu std [T 0008x004000 007Fx020000] 16Mb
number of flash chip/regions detected: 02/01
Initialize Done
Set baud ...
115200
Set baud Done
Initialize bootcode ...
Initialize bootcode Done
Check firmware integrity ...
device parameters autodetection in progress...
detecting chip #00 in region #00...
flash: 98000300000001:18E59F00000000
flash: AMD/Fujitsu std [T 0008x004000 007Fx020000] 16Mb
detecting chip #01 in region #00...
flash: 98000300000001:18E59F00000000
flash: AMD/Fujitsu std [T 0008x004000 007Fx020000] 16Mb
it's time to stop: 18F09FE518F09FE518F09FE518F09FE518F09FE518F09FE5
number of flash chip/regions detected: 01/01
total flash region size: 01000000
detect device identification#1...
detection phase #1...
detect device identification#1 finished
identification#1 structure: 2nd [standard] generation
identification#1 protocol ver: 04
ver. sw 1: MT6225_GEMINI_PCB01_GPRS_MT6225_S00.SYGJ_6300_1_2_ 3_2.BIN
ver. sw 2: sygj.6300.1.2.3.2, 00000000
ffs offset/size: 00E00000/00200000
detect device identification#2...
detection phase #1...
.
warning: optional information is not found,
if phone works well just ignore this warning
detect device identification#2 finished
detecting eeprom/ffs area in 1 chip(s)...
standard eeprom/ffs offset detected: 00E00000
flash: 98000300000001:18E59F00000000
checking area [00000000]: 00000000-00FFFFFF...
eeprom/ffs found near: 00E00000
detecting eeprom/ffs size...
eeprom/ffs size: 00200000
ffs chip: 00
eeprom/ffs area: 00000000:00E00000-00FFFFFF
Check firmware integrity Done
Check firmware content ...
Check firmware content Done
Backup required data ...
reading: eeprom[MT6225_GEMINI_PCB01_GPRS_MT6225_S00.SYGJ_6300_1_2_ 3_2.BIN]...
file saved: D:\china 6300\eeprom[MT6225_GEMINI_PCB01_GPRS_MT6225_S00.SYGJ_6300_1_2_ 3_2.BIN]_20090729-133207.B0E.bin
flash: 98000300000001:18E59F00000000
Backup required data Done
Patch required data ...
Patch required data Done
Special operation ...
Special operation Done
Write ...
detect device identification#2...
detection phase #1...
.
warning: optional information is not found,
if phone works well just ignore this warning
detect device identification#2 finished
detecting security area (code #2)...
security area (code #2) is absent
Area: Firmware
flash: 98000300000001:18E59F00000000
Write: Firmware
error: error# 0000FFFF
error: flash write error: 00000000:00002000
detect device identification#2...
detection phase #1...
.
warning: optional information is not found,
if phone works well just ignore this warning
detect device identification#2 finished
Write Fail
Finished, time used: 303 sec
Remove/Install battery now !
WARNING ! Settings will be cleared, user data erased, Imei set to default value !
Make flash backup before this procedure !

Do you want to continue ?

I pressed no

could some one pliz advise me

on how to proceed now it cannot flash.

now iget this

module v2.73
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
Action: write NOR flash
"smart write" active
write: Firmware
skip: Customization/Language Pack
skip: Customization
write: Eeprom/ffs
eeprom backup enabled, it may takes several minutes !
Boot ...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing [6225:8A05:8A00]...
CPU: MT6225
high speed boot On
chip: 0001:7F03:0008
boot packet size: 0400
Release Power button now !
Boot Done
Initialize ...
detecting chip #00 in region #00...
flash: 98000300000001:FFFFFF00000000
flash: AMD/Fujitsu std [T 0008x004000 007Fx020000] 16Mb
detecting chip #01 in region #00...
flash: 98000300000001:FFFFFF00000000
flash: AMD/Fujitsu std [T 0008x004000 007Fx020000] 16Mb
number of flash chip/regions detected: 02/01
Initialize Done
Set baud ...
115200
Set baud Done
Initialize bootcode ...
Initialize bootcode Done
Check firmware integrity ...
device parameters autodetection in progress...
detecting chip #00 in region #00...
flash: 98000300000001:FFFFFF00000000
flash: AMD/Fujitsu std [T 0008x004000 007Fx020000] 16Mb
Warning: probably flash chip empty, erased, incorrectly flashed or damaged.

What to do:
1. go to software "Settings" page
2. set "Advanced chip detection method" box UN-CHECKED !
3. make flash write operation

If still no luck: send mail to support (mt62xx@gmail.com) with detailed description of problem,
attach the next files in your e-mail:
1. C:\Program Files\InfinityBox\ChineseMiracle\operation.log
2. C:\Program Files\InfinityBox\ChineseMiracle\cfi_xxxx_xxxx.bin
detecting chip #01 in region #00...
flash: 98000300000001:FFFFFF00000000
flash: AMD/Fujitsu std [T 0008x004000 007Fx020000] 16Mb
it's time to stop: FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF
number of flash chip/regions detected: 01/01
total flash region size: 01000000
detect device identification#1...
detection phase #1...
.
detection phase #2...
.................................................. .................................................. ............................
warning: identification#1 information not found, possible reasons:
.old firmware type w/o identification#1 data
.damaged firmware
.damaged hardware
if phone works fine just ignore this warning
detect device identification#1 finished
detect device identification#2...
detection phase #1...
.
warning: optional information is not found,
if phone works well just ignore this warning
detect device identification#2 finished
detecting eeprom/ffs area in 1 chip(s)...
standard eeprom/ffs offset assigned: 00E00000
flash: 98000300000001:FFFFFF00000000
checking area [00000000]: 00000000-00FFFFFF...
eeprom/ffs found near: 00E00000
detecting eeprom/ffs size...
eeprom/ffs size: 00200000
ffs chip: 00
eeprom/ffs area: 00000000:00E00000-00FFFFFF
Check firmware integrity Done
Check firmware content ...
Check firmware content Done
Backup required data ...
reading: eeprom...
file saved: C:\Program Files\InfinityBox\ChineseMiracle\eeprom_20090729-134228.B0E.bin
flash: 98000300000001:FFFFFF00000000
Backup required data Done
Patch required data ...
Patch required data Done
Special operation ...
Special operation Done
Write ...
detect device identification#1...
detection phase #1...
.
detection phase #2...
.................................................. .................................................. ............................
warning: identification#1 information not found, possible reasons:
.old firmware type w/o identification#1 data
.damaged firmware
.damaged hardware
if phone works fine just ignore this warning
detect device identification#1 finished
detect device identification#2...
detection phase #1...
.
warning: optional information is not found,
if phone works well just ignore this warning
detect device identification#2 finished
detecting security area (code #2)...
security area (code #2) is absent
Area: Firmware
flash: 98000300000001:FFFFFF00000000
Write: Firmware
error: error# 0000FFFF
error: flash write error: 00000000:00002000
error: error# 0000FFFF
error: flash write error: 00000000:00002000
error: error# 0000FFFF
error: flash write error: 00000000:00002000
error: error# 0000FFFF
error: flash write error: 00000000:00002000
error: error# 0000FFFF
error: flash write error: 00000000:00002000
error: error# 0000FFFF
error: flash write error: 00000000:00002000
error: error# 0000FFFF
error: flash write error: 00000000:00002000
error: error# 0000FFFF
error: flash write error: 00000000:00002000
error: error# 0000FFFF
error: flash write error: 00000000:00002000
error: error# 0000FFFF
error: flash write error: 00000000:00002000
error: error# 0000FFFF
error: flash write error: 00000000:00002000
error: error# 0000FFFF
error: flash write error: 00000000:00002000
detect device identification#2...
detection phase #1...
.
warning: optional information is not found,
if phone works well just ignore this warning
detect device identification#2 finished
Write Fail
Finished, time used: 360 sec
Remove/Install battery now !