Gprs_mt6228_s02.r888_320_7670_hyn_hy128_v2_1

[adnanali]

Initialize Done
Set baud ...
slowest
Set baud Done
Identification ...
reading structure area...
detecting structure...
source data: page only
identification#1 protocol ver: 04
ver. sw 1: BXWY28_06B_PCB04_GPRS_MT6228_S02.R888_320_7670_HYN _HY128_V2_1.BIN
ver. sw 2: R888_320_7670_Hyn_Hy128_V2.1, 40619D2D
ffs offset/size: 02000000/06000000
id-page1 Ok
nfi area detection finished: Ok
identification#1 structure: 2nd [enhanced] generation
security area (code #1) is Ok
security area (code #1) backup saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_security\i d.27EADFDB.[BXWY28_06B_PCB04_GPRS_MT6228_S02.R888_320_7670_HYN _HY128_V2_1.BIN_D2629EBF].rpl
identification#1 detection finished
security area (code #1) calculation...
Identification Done
Write ...
file saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_security\s ystem_log_27EADFDB_BXWY28_06B_PCB04_GPRS_MT6228_S0 2.R888_320_7670_HYN_HY128_V2_1.BIN_D2629EBF_200811 24-035301.B4X.bin
write core area 1 of 3...
write core area 2 of 3...
write core area 3 of 3...
Write Done
file saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_security\s ystem_log_27EADFDB_BXWY28_06B_PCB04_GPRS_MT6228_S0 2.R888_320_7670_HYN_HY128_V2_1.BIN_D2629EBF_200811 24-042614.B4X.bin
Finished, time used: 2081 sec
Remove/Install battery now !



dear infinity team
set comes in auto shutdown fault now after flash dead plz what is your recomendation plz when i use safe format for this phone shows ...



19200 autodetect
Initializing [6228:8A02:8A02]...
CPU: MT6228
high speed boot enabled
chip: 0031:0000:0101
Connecting, wait...
error: can't finalize test mode
repeat operation and HOLD phone "Power" button long time !
error: operation failed !
Finished, time used: 100 sec
Remove/Install battery now !

[InfinityHelp]

hello!

i would advice: flashfiles/ChineseMiracle/_MT6228/BXWY28_06B_PCB04_GPRS_MT6228_S02.R888_320_7670_HYN _HY128_V2_1__I808_128m_En_Cn.B4M.bin

[adnanali]

Set baud ...
slowest
Set baud Done
Identification ...
reading structure area...
detecting structure...
source data: page only
identification#1 protocol ver: 04
ver. sw 1: BXWY28_06B_PCB04_GPRS_MT6228_S02.R888_320_7670_HYN _HY128_V2_1.BIN
ver. sw 2: R888_320_7670_Hyn_Hy128_V2.1, 40619D2D
ffs offset/size: 02000000/06000000
id-page1 Ok
nfi area detection finished: Ok
identification#1 structure: 2nd [enhanced] generation
security area (code #1) is Ok
security area (code #1) backup saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_security\i d.27EADFDB.[BXWY28_06B_PCB04_GPRS_MT6228_S02.R888_320_7670_HYN _HY128_V2_1.BIN_D2629EBF].rpl
identification#1 detection finished
security area (code #1) calculation...
Identification Done
Write ...
file saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_security\s ystem_log_27EADFDB_BXWY28_06B_PCB04_GPRS_MT6228_S0 2.R888_320_7670_HYN_HY128_V2_1.BIN_D2629EBF_200811 25-081624.B4X.bin
write core area 1 of 3...
write core area 2 of 3...
write core area 3 of 3...
Write Done
file saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_security\s ystem_log_27EADFDB_BXWY28_06B_PCB04_GPRS_MT6228_S0 2.R888_320_7670_HYN_HY128_V2_1.BIN_D2629EBF_200811 25-084937.B4X.bin
Finished, time used: 2083 sec
Remove/Install battery now !


sir flash ok but same condition plz any more

[InfinityHelp]

hello!

unfortunately, 6228 MCU is very unstable one.
most its problems caused not by software reasons, but by hardware faults/conflicts
you can try format FFS complete.
but if will not work- i think it must be returned back to customer