Nokia n82 copy

[gsmkiller173]

i need eeprom files i cant found on support area i have flash it but set is same .set is on but lcd have no image plz help me .set was on good but in flight mode i have done format and its goes to dead. then i flash and set is now on but lcd??????????????? plz help need good eeprom file r tell me whats happend


hear is log



COM7 [VCP0] selected
module v2.71
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
Action: "format ffs"
eeprom backup enabled, it may takes several minutes !
Boot ...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing [6225:8A03:8A00]...
CPU: MT6225
high speed boot On
chip: 0001:CD03:000A
boot packet size: 0400
Release Power button now !
Boot Done
Initialize ...
detecting chip #00 in region #00...
flash: EC257E25082501:18E59F00000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
detecting chip #01 in region #00...
flash: EC257E25082501:18E59F00000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
number of flash chip/regions detected: 02/01
Initialize Done
Set baud ...
460800
Set baud Done
Initialize bootcode ...
Initialize bootcode Done
Check firmware integrity ...
device parameters autodetection in progress...
detecting chip #00 in region #00...
flash: EC257E25082501:18E59F00000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
detecting chip #01 in region #00...
flash: EC257E25082501:18E59F00000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
it's time to stop: 18F09FE518F09FE518F09FE518F09FE518F09FE518F09FE5
number of flash chip/regions detected: 01/01
total flash region size: 01000000
detect device identification#1...
detection phase #1...
detect device identification#1 finished
identification#1 structure: 2nd [enhanced] generation
security area (code #1) is Ok
security area (code #1) backup saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_security\i d.6438D47F.[TOP25_06B_PCB01_GPRS_MT6225_S00.24D_SN_OV_T_B_F_U_ 2506B_V_0_18.BIN_2E180BB4].rpl
identification#1 detection finished
device-id: 6438D47F
identification#1 protocol ver: 04
ver. sw 1: TOP25_06B_PCB01_GPRS_MT6225_S00.24D_SN_OV_T_B_F_U_ 2506B_V_0_18.BIN
ver. sw 2: 24D_SN_OV_T_B_F_U_2506B_V_0_18, 4BF4E7D1
ffs offset/size: 00E00000/00200000
detect device identification#2...
detection phase #1...
.
warning: optional information is not found,
if phone works well just ignore this warning
detect device identification#2 finished
detecting eeprom/ffs area in 1 chip(s)...
standard eeprom/ffs offset detected: 00E00000
flash: EC257E25082501:18E59F00000000
checking area [00000000]: 00000000-00FFFFFF...
eeprom/ffs found near: 00790000
Detected eeprom/ffs address is non-standard: 00790000
Posible reasons:
1. eeprom is Ok but address is non-standard
2. eeprom damaged and can't be detected
3. eeprom is Ok but detected incorrectly (f.e. unknown eeprom structure)
If you are not sure that detected address is correct:
1. press "NO" (and select standard address or terminate current operation)
2. make flash backup for emergency case
3. repeat required operation
Are you sure that detected eeprom address is correct ?
Do you want to use standard eeprom address: 00E00000 ?
If you are not sure that standard address is correct:
1. press "NO" and terminate current operation
2. make flash backup for emergency case
3. repeat required operation
terminated by user
error: critical error#1 during ffs size detection
error: can't detect eeprom/ffs address/size
Check firmware integrity Done
Check firmware content ...
Check firmware content Done
Backup required data ...
flash: EC257E25082501:18E59F00000000
Backup required data Done
Patch required data ...
Patch required data Done
Special operation ...
Special operation Done
Write ...
Write Done
Finalization ...
formatting...
flash: EC257E25082501:18E59F00000000
Finalization Done
file saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_security\s ystem_log_6438D47F_TOP25_06B_PCB01_GPRS_MT6225_S00 .24D_SN_OV_T_B_F_U_2506B_V_0_18.BIN_2E180BB4_20081 215-135621.B0X.bin
Finished, time used: 139 sec
Remove/Install battery now !
File system has been modified !
It is need to press and HOLD phone "Power" button
during long time (up to 1 min) to make phone Powered-On !

[InfinityHelp]

hello!

are you sure that this is phone's original version?
TOP25_06B_PCB01_GPRS_MT6225_S00.24D_SN_OV_T_B_F_U_ 2506B_V_0_18
you can check this in operation log, look for first format operation

[gsmkiller173]

yes its same with first format log and same as last



its is the 100% orignal version i need eeprom file plz help

[InfinityHelp]

hello!

flash phone by this fiie:
flashfiles/ChineseMiracle/_MT6225/TOP25_06B_PCB01_GPRS_MT6225_S00.24D_SN_OV_T_B_F_U_ 2506B_V_0_18__NOKIA_N82_COPY_16m_En_Ru_Fr_It_De_Th _Vn_Tr_Ar.B0M.bin
and make format FFS complete after

[gsmkiller173]

warning: optional information is not found,
if phone works well just ignore this warning
detect device identification#2 finished
detecting eeprom/ffs area in 1 chip(s)...
standard eeprom/ffs offset detected: 00E00000
flash: EC257E25082501:18E59F00000000
checking area [00000000]: 00000000-00FFFFFF...
eeprom/ffs found near: 00790000
Detected eeprom/ffs address is non-standard: 00790000

Posible reasons:
1. eeprom is Ok but address is non-standard
2. eeprom damaged and can't be detected
3. eeprom is Ok but detected incorrectly (f.e. unknown eeprom structure)

If you are not sure that detected address is correct:
1. press "NO" (and select standard address or terminate current operation)
2. make flash backup for emergency case
3. repeat required operation

Are you sure that detected eeprom address is correct ?
Do you want to use standard eeprom address: 00E00000 ?

If you are not sure that standard address is correct:
1. press "NO" and terminate current operation
2. make flash backup for emergency case
3. repeat required operation








it will give this error

[InfinitySupport]

warning: optional information is not found,
if phone works well just ignore this warning
detect device identification#2 finished
detecting eeprom/ffs area in 1 chip(s)...
standard eeprom/ffs offset detected: 00E00000
flash: EC257E25082501:18E59F00000000
checking area [00000000]: 00000000-00FFFFFF...
eeprom/ffs found near: 00790000
Detected eeprom/ffs address is non-standard: 00790000

Posible reasons:
1. eeprom is Ok but address is non-standard
2. eeprom damaged and can't be detected
3. eeprom is Ok but detected incorrectly (f.e. unknown eeprom structure)

If you are not sure that detected address is correct:
1. press "NO" (and select standard address or terminate current operation)
2. make flash backup for emergency case
3. repeat required operation

Are you sure that detected eeprom address is correct ?
Do you want to use standard eeprom address: 00E00000 ?

If you are not sure that standard address is correct:
1. press "NO" and terminate current operation
2. make flash backup for emergency case
3. repeat required operation








it will give this error

Hello,

Please, explain what is not clear in given instruction and we will try to explain it better.

[gsmkiller173]

set is in flight mode i have made complete format .in formate when soft is reading eeprom he said ffs eeprom address is non-standard
press yes to make standard ar no to repeart this opreation again

i am press yes after this set is dead
i have flash with this file
TOP25_06B_PCB01_GPRS_MT6225_S00.24D_SN_OV_T_B_F_U_ 2506B_V_0_18__NOKIA_N82_COPY_16m_En_Ru_Fr_It_De_Th _Vn_Tr_Ar.B0M


after flashing set is ok but lcd is black to light no logo
after flash i have done again format but same not standrad addres prs yes to make standred r no to repeart again

[InfinitySupport]

set is in flight mode i have made complete format .in formate when soft is reading eeprom he said ffs eeprom address is non-standard
press yes to make standard ar no to repeart this opreation again

i am press yes after this set is dead
i have flash with this file
TOP25_06B_PCB01_GPRS_MT6225_S00.24D_SN_OV_T_B_F_U_ 2506B_V_0_18__NOKIA_N82_COPY_16m_En_Ru_Fr_It_De_Th _Vn_Tr_Ar.B0M


after flashing set is ok but lcd is black to light no logo
after flash i have done again format but same not standrad addres prs yes to make standred r no to repeart again

Hello,

Please, check instruction in log one more time, it was given an advice to read full flash for emergency case.

Now you must flash phone with other firmware that has support for your phone LCD hardware type.

[fazi52]

Hello,

Please, check instruction in log one more time, it was given an advice to read full flash for emergency case.

Now you must flash phone with other firmware that has support for your phone LCD hardware type.



but there is only 1 file in support area hows to know any other files????????????

[InfinitySupport]

Hello,

You need to find file with version similar (not exact but similar) to this version: TOP25_06B_PCB01_GPRS_MT6225_S00.24D_SN_OV_T_B_F_U_ 2506B_V_0_18

[gsmkiller173]

Hello,

You need to find file with version similar (not exact but similar) to this version: TOP25_06B_PCB01_GPRS_MT6225_S00.24D_SN_OV_T_B_F_U_ 2506B_V_0_18




hope i m right it is the right firmware ver(MT6225_S00.24D) what u say there is nothing match any other files

[InfinityHelp]

hello!

you can try this one:
flashfiles/ChineseMiracle/_MT6225/TOP25_06B_PCB01_GPRS_MT6225_S00.206_OV_T_B_F_U_250 6B_V_0_5_FLG3_16m_En_Ru_Fr_De_Farsi_Pt_Ar.B0M.bin

[InfinityHelp]

hello!

you can try this one:
flashfiles/ChineseMiracle/_MT6225/TOP25_06B_PCB01_GPRS_MT6225_S00.206_OV_T_B_F_U_250 6B_V_0_5_FLG3_16m_En_Ru_Fr_De_Farsi_Pt_Ar.B0M.bin

[gsmkiller173]

TOP25_06B_PCB01_GPRS_MT6225_S00.24D_SN_OV_T_B_F_U_ 2506B_V_0_18


thxxxxxxxxxxxxxxxxxx
problem was solved with this flash file any many tries .flash again flash and again and done