mt6227 dead

[sebY7676]

Hi, pls help me, MT6227 dead after format ffs

Here is log

==== log: [16/12/2008 21:17:18] ====
COM5 [VCP0] selected
module v2.71
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
Action: "format ffs"
eeprom backup enabled, it may takes several minutes !
Boot ...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing [6226:8A02:8A01]...
CPU: MT6226
high speed boot Off
chip: 0031:3E7C:82EA
high speed boot Off
boot packet size: 0002
Release Power button now !
Boot Done
Initialize ...
detecting chip #00 in region #00...
flash: EC257E25082501:29EA0000000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
detecting chip #01 in region #00...
flash: EC257E25082501:29EA0000000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
number of flash chip/regions detected: 02/01
Initialize Done
Set baud ...
460800
Set baud Done
Initialize bootcode ...
Initialize bootcode Done
Check firmware integrity ...
device parameters autodetection in progress...
detecting chip #00 in region #00...
flash: EC257E25082501:29EA0000000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
detecting chip #01 in region #00...
flash: EC257E25082501:29EA0000000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
it's time to stop: 290000EA18F09FE518F09FE518F09FE518F09FE518F09FE5
number of flash chip/regions detected: 01/01
total flash region size: 01000000
detect device identification#1...
detection phase #1...
detect device identification#1 finished
identification#1 structure: 2nd [enhanced] generation
security area (code #1) is Ok
security area (code #1) backup saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_security\i d.D42B38B8.[E551_C8ARVFBT_E551_GPRS_MT6226_S01.01_1.BIN_3818F9 49].rpl
New firmware detected (2.71) :
E551_C8ARVFBT_E551_GPRS_MT6226_S01.01_1.BIN

- make "Read full flash" operation
- send "system_log_..." file to support: mt62xx@gmail.com
- send flash backup file(s) to support: mt62xx@gmail.com
- include in your e-mail full text from phone back label (phone name etc.)
identification#1 detection finished
device-id: D42B38B8
identification#1 protocol ver: 04
ver. sw 1: E551_C8ARVFBT_E551_GPRS_MT6226_S01.01_1.BIN
ver. sw 2: E551_C8ARVFBT.01.1, B606E7C7
ffs offset/size: 00800000/001FF000
detect device identification#2...
detection phase #1...
.
warning: optional information is not found,
if phone works well just ignore this warning
detect device identification#2 finished
detecting eeprom/ffs area in 1 chip(s)...
standard eeprom/ffs offset detected: 00800000
flash: EC257E25082501:29EA0000000000
checking area [00000000]: 00000000-00FFFFFF...
eeprom/ffs found near: 00E00000
Detected eeprom/ffs address is non-standard: 00E00000

Posible reasons:
1. eeprom is Ok but address is non-standard
2. eeprom damaged and can't be detected
3. eeprom is Ok but detected incorrectly (f.e. unknown eeprom structure)

If you are not sure that detected address is correct:
1. press "NO" (and select standard address or terminate current operation)
2. make flash backup for emergency case
3. repeat required operation

Are you sure that detected eeprom address is correct ?
Do you want to use standard eeprom address: 00800000 ?

If you are not sure that standard address is correct:
1. press "NO" and terminate current operation
2. make flash backup for emergency case
3. repeat required operation
terminated by user
error: critical error#1 during ffs size detection
error: can't detect eeprom/ffs address/size
Check firmware integrity Done
Check firmware content ...
Check firmware content Done
Backup required data ...
flash: EC257E25082501:29EA0000000000
Backup required data Done
Patch required data ...
Patch required data Done
Special operation ...
Special operation Done
Write ...
Write Done
Finalization ...
formatting...
flash: EC257E25082501:29EA0000000000
Finalization Done
file saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_security\s ystem_log_D42B38B8_E551_C8ARVFBT_E551_GPRS_MT6226_ S01.01_1.BIN_3818F949_20081216-212100.B0X.bin
Finished, time used: 198 sec
Remove/Install battery now !

File system has been modified !
It is need to press and HOLD phone "Power" button
during long time (up to 1 min) to make phone Powered-On !

[InfinityHelp]

hello!

have you made backup as program asked you?

[sebY7676]

Problem solved writting back-up flash, but still remaining two problems: first, i can now to acces bluetooth menu,but when i try to power-up bluetooth,the message is "INITIALIZING BLUETOOTH NOW, WAIT A MOMENT".

Second, the signal from both networks lost sometimes.

Here is log

==== log opened: [16/12/2008 21:35:02] ====

Device: Autodetect 6205-6227 NOR
Done
Loading file v.02...
flash[E551_C8ARVFBT_E551_GPRS_MT6226_S01.01_1.BIN]_20081216-195336.B0M.bin loaded
identification#1 protocol ver: 04
ver. sw 1: E551_C8ARVFBT_E551_GPRS_MT6226_S01.01_1.BIN
ver. sw 2: E551_C8ARVFBT.01.1, B606E7C7
Loaded file w/protection: security area (code #1)
detecting languages...
Languages: En Ru Fr Vn Ar

==== log: [16/12/2008 21:36:58] ====
COM5 [VCP0] selected
module v2.71
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
Action: write NOR flash
"smart write" active
write: Firmware
skip: Customization/Language Pack
skip: Customization
skip: Eeprom/ffs
eeprom backup enabled, it may takes several minutes !
Boot ...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing [6226:8A02:8A01]...
CPU: MT6226
high speed boot Off
chip: 0031:3E7C:82EA
high speed boot Off
boot packet size: 0002
Release Power button now !
Boot Done
Initialize ...
detecting chip #00 in region #00...
flash: EC257E25082501:FFFFFF00000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
detecting chip #01 in region #00...
flash: EC257E25082501:FFFFFF00000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
number of flash chip/regions detected: 02/01
Initialize Done
Set baud ...
460800
Set baud Done
Initialize bootcode ...
Initialize bootcode Done
Check firmware integrity ...
device parameters autodetection in progress...
detecting chip #00 in region #00...
flash: EC257E25082501:FFFFFF00000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
Warning: probably flash chip empty, erased, incorrectly flashed or damaged.

What to do:
1. go to software "Settings" page
2. set "Advanced chip detection method" box UN-CHECKED !
3. make flash write operation

If still no luck: send mail to support (mt62xx@gmail.com) with detailed description of problem,
attach the next files in your e-mail:
1. C:\Program Files\InfinityBox\ChineseMiracle\operation.log
2. C:\Program Files\InfinityBox\ChineseMiracle\cfi_xxxx_xxxx.bin
detecting chip #01 in region #00...
flash: EC257E25082501:FFFFFF00000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
it's time to stop: FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF
number of flash chip/regions detected: 01/01
total flash region size: 01000000
detect device identification#1...
detection phase #1...
.
detection phase #2...
.................................................. .................................................. ............................
warning: identification#1 information not found, possible reasons:
.old firmware type w/o identification#1 data
.damaged firmware
.damaged hardware
if phone works fine just ignore this warning
detect device identification#1 finished
detect device identification#2...
detection phase #1...
.
warning: optional information is not found,
if phone works well just ignore this warning
detect device identification#2 finished
detecting eeprom/ffs area in 1 chip(s)...
standard eeprom/ffs offset assigned: 00E00000
flash: EC257E25082501:FFFFFF00000000
checking area [00000000]: 00000000-00FFFFFF...
eeprom/ffs found near: 00E00000
detecting eeprom/ffs size...
eeprom/ffs size: 00200000
ffs chip: 00
eeprom/ffs area: 00000000:00E00000-00FFFFFF
Check firmware integrity Done
Check firmware content ...
Check firmware content Done
Backup required data ...
reading: eeprom...
file saved: C:\Program Files\InfinityBox\ChineseMiracle\eeprom_20081216-214243.B0E.bin
flash: EC257E25082501:FFFFFF00000000
Backup required data Done
Patch required data ...
Patch required data Done
Special operation ...
Special operation Done
Write ...
detect device identification#1...
detection phase #1...
.
detection phase #2...
.................................................. .................................................. ............................
warning: identification#1 information not found, possible reasons:
.old firmware type w/o identification#1 data
.damaged firmware
.damaged hardware
if phone works fine just ignore this warning
detect device identification#1 finished
detect device identification#2...
detection phase #1...
.
warning: optional information is not found,
if phone works well just ignore this warning
detect device identification#2 finished
warning: rpl file not found: C:\Program Files\InfinityBox\ChineseMiracle\id.D42B38B8.[E551_C8ARVFBT_E551_GPRS_MT6226_S01.01_1.BIN_3818F9 49].rpl
warning: rpl file not found: C:\Program Files\InfinityBox\ChineseMiracle\id.D42B38B8._E551 _C8ARVFBT_E551_GPRS_MT6226_S01.01_1.BIN_3818F949_. rpl
security area (code #1) backup loaded
security area (code #1) calculation...
done
detecting security area (code #2)...
security area (code #2) is absent
Area: Firmware
flash: EC257E25082501:FFFFFF00000000
Write: Firmware
detect device identification#2...
detection phase #1...
.
warning: optional information is not found,
if phone works well just ignore this warning
detect device identification#2 finished
Write Done
Finalization ...
Finalization Done
Finished, time used: 501 sec
Remove/Install battery now !

[sebY7676]

And now, i tyed second time to format ffs, but another error:


Wait...
Device: Autodetect 6205-6227 NOR
Done
WARNING ! Settings will be cleared, user data erased, Imei set to default value !
Make flash backup before this procedure !

Do you want to continue ?
operation aborted
WARNING ! Settings will be cleared, user data erased, Imei set to default value !
Make flash backup before this procedure !

Do you want to continue ?

==== log: [16/12/2008 22:04:16] ====
COM5 [VCP0] selected
module v2.71
Action: reset settings
Model: Autodetect 6205-6227 NOR
Checking data, wait...
Phone should be Switched OFF !
Press and HOLD Power button now !
19200 autodetect
Initializing [6226:8A02:8A01]...
CPU: MT6226
high speed boot Off
chip: 0031:3E7C:82EA
Connecting, wait...
warning: wrong packet cs
error: can't finalize test mode
repeat operation and HOLD phone "Power" button long time !
error: operation failed !
Finished, time used: 34 sec
Remove/Install battery now !
WARNING ! Settings will be cleared, user data erased, Imei set to default value !
Make flash backup before this procedure !

Do you want to continue ?

==== log: [16/12/2008 22:05:10] ====
COM5 [VCP0] selected
module v2.71
Action: reset settings
Model: Autodetect 6205-6227 NOR
Checking data, wait...
Phone should be Switched OFF !
Press and HOLD Power button now !
19200 autodetect
Initializing [6226:8A02:8A01]...
CPU: MT6226
high speed boot Off
chip: 0031:3E7C:82EA
Connecting, wait...
Release Power button now !
Phone detected, wait...
Hardware: MT6226,E02
Date: 2005.04.12
Version: 1.0
Version: E551_C8ARVFBT.01.1_26S01
Version: M500Z_05C_HW
detecting structure #2...
done
60 byte(s) read
imei: 135XXXXXXXXXXX
warning: current phone imei is incorrect !
It's need to repair imei for correct phone functionality !
connection Ok
building list...
done
items to clear: 203
warning: wrong packet cs
warning: wrong packet cs
items cleared: 203 of 203
building list...
done
items remains: 0
Finished, time used: 48 sec
Remove/Install battery now !



The phone work well, but lose the signal, and bluetooth can't power on.Please help me

[sebY7676]

Imei problem done with reflasing(rpl file).When format ffs, i can acces blutooth menu,but cant power-on bluetooth and imei is broken. After flash,imei is ok, but cant acces bluetooth menu.Still signal problem(sometime lost).

Here is log file:



Loading file v.02...
flash[E551_C8ARVFBT_E551_GPRS_MT6226_S01.01_1.BIN]_20081216-195336.B0M.bin loaded
identification#1 protocol ver: 04
ver. sw 1: E551_C8ARVFBT_E551_GPRS_MT6226_S01.01_1.BIN
ver. sw 2: E551_C8ARVFBT.01.1, B606E7C7
Loaded file w/protection: security area (code #1)
detecting languages...
Languages: En Ru Fr Vn Ar

==== log: [17/12/2008 08:06:33] ====
COM5 [VCP0] selected
module v2.71
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection disabled
Action: write NOR flash
"smart write" active
write: Firmware
skip: Customization/Language Pack
skip: Customization
skip: Eeprom/ffs
eeprom backup enabled, it may takes several minutes !
Boot ...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing [6226:8A02:8A01]...
CPU: MT6226
high speed boot Off
chip: 0031:3E7C:82EA
high speed boot Off
boot packet size: 0002
Release Power button now !
Boot Done
Initialize ...
detecting chip #00 in region #00...
flash: EC257E25082501:29EA0000000000
flash: Samsung D 16Mb
detecting chip #01 in region #00...
flash: EC257E25082501:29EA0000000000
flash: Samsung D 16Mb
number of flash chip/regions detected: 02/01
Initialize Done
Set baud ...
460800
Set baud Done
Initialize bootcode ...
Initialize bootcode Done
Check firmware integrity ...
device parameters autodetection in progress...
detecting chip #00 in region #00...
flash: EC257E25082501:29EA0000000000
flash: Samsung D 16Mb
detecting chip #01 in region #00...
flash: EC257E25082501:29EA0000000000
flash: Samsung D 16Mb
it's time to stop: 290000EA18F09FE518F09FE518F09FE518F09FE518F09FE5
number of flash chip/regions detected: 01/01
total flash region size: 01000000
detect device identification#1...
detection phase #1...
detect device identification#1 finished
identification#1 structure: 2nd [enhanced] generation
security area (code #1) is Ok
security area (code #1) backup saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_security\i d.D42B38B8.[E551_C8ARVFBT_E551_GPRS_MT6226_S01.01_1.BIN_3818F9 49].rpl
New firmware detected (2.71) :
E551_C8ARVFBT_E551_GPRS_MT6226_S01.01_1.BIN

- make "Read full flash" operation
- send "system_log_..." file to support: mt62xx@gmail.com
- send flash backup file(s) to support: mt62xx@gmail.com
- include in your e-mail full text from phone back label (phone name etc.)
identification#1 detection finished
device-id: D42B38B8
identification#1 protocol ver: 04
ver. sw 1: E551_C8ARVFBT_E551_GPRS_MT6226_S01.01_1.BIN
ver. sw 2: E551_C8ARVFBT.01.1, B606E7C7
ffs offset/size: 00800000/001FF000
detect device identification#2...
detection phase #1...
.
warning: optional information is not found,
if phone works well just ignore this warning
detect device identification#2 finished
detecting eeprom/ffs area in 1 chip(s)...
standard eeprom/ffs offset detected: 00800000
flash: EC257E25082501:29EA0000000000
checking area [00000000]: 00000000-00FFFFFF...
eeprom/ffs found near: 00E00000
Detected eeprom/ffs address is non-standard: 00E00000

Posible reasons:
1. eeprom is Ok but address is non-standard
2. eeprom damaged and can't be detected
3. eeprom is Ok but detected incorrectly (f.e. unknown eeprom structure)

If you are not sure that detected address is correct:
1. press "NO" (and select standard address or terminate current operation)
2. make flash backup for emergency case
3. repeat required operation

Are you sure that detected eeprom address is correct ?
autodetected eeprom/ffs address confirmed by user: 00E00000
detecting eeprom/ffs size...
eeprom/ffs size: 00200000
ffs chip: 00
eeprom/ffs area: 00000000:00E00000-00FFFFFF
Check firmware integrity Done
Check firmware content ...
Check firmware content Done
Backup required data ...
reading: eeprom[E551_C8ARVFBT_E551_GPRS_MT6226_S01.01_1.BIN]...
file saved: C:\Program Files\InfinityBox\ChineseMiracle\eeprom[E551_C8ARVFBT_E551_GPRS_MT6226_S01.01_1.BIN]_20081217-081028.B0E.bin
flash: EC257E25082501:29EA0000000000
Backup required data Done
Patch required data ...
Patch required data Done
Special operation ...
Special operation Done
Write ...
detect device identification#2...
detection phase #1...
.
warning: optional information is not found,
if phone works well just ignore this warning
detect device identification#2 finished
security area (code #1) backup loaded
security area (code #1) calculation...
done
detecting security area (code #2)...
security area (code #2) is absent
file saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_security\s ystem_log_D42B38B8_E551_C8ARVFBT_E551_GPRS_MT6226_ S01.01_1.BIN_3818F949_20081217-081042.B0X.bin
Area: Firmware
flash: EC257E25082501:29EA0000000000
Write: Firmware
detect device identification#2...
detection phase #1...
.
warning: optional information is not found,
if phone works well just ignore this warning
detect device identification#2 finished
Write Done
Finalization ...
Finalization Done
file saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_security\s ystem_log_D42B38B8_E551_C8ARVFBT_E551_GPRS_MT6226_ S01.01_1.BIN_3818F949_20081217-081233.B0X.bin
Finished, time used: 357 sec
Remove/Install battery now !






I send files to mt62xx@gmail.com

[InfinitySupport]

Hello,

It looks like it's hardware problem but not software. I strongly suggest you to check phone hardware.