View Full Version : tamper aler in talk about ... Ver c4_13_03 .
Hi Friends ,
i tried to unlock 3 phones talkabout like usual with my roemmi today and i got tamper alert msg . i shocked cuz we didn't used to check versions before unlock mot phones !!
so i have big problem noW ,
i got ver by test card 19# .
its new mot as i readed here in forum now but i need to get it back to special code or need to remove this alert ...
plz help me ....
Very special thnx .
Regards
I know swvwral methods for repairing with test vard. Do you have test card?
I know several methods for repairing with Test Card. Do you have it?
Hmmm,
How can i am do fix temper alert with a test card.
Bye Ron
hanskemp@planet.nl
07-28-2001, 11:27
Hello Asas
I have a test-card please how repair
tamper alert
Thanks Hans
Try all methods:
1.
GO IN TEST MODE.
*#03# YOUR DISPLAY SHOW THE PACAL NUMBER(REMEMBER THE PACAL NUMBER!!!!)AND NOW PRESS
*#030(PACAL NUMBER)# POWEWR OFF THE PHONE AND TRY...
2.
The test card can actually be used to make the phone recalculate the configuration checksum at $0000-$0001 after you have manually edited the EEPROM data. After powering up the phone it will go: "phone failed - see supplier" on the display. By updating the PA calibration table, the configuration checksum will be recalculated.
Enter testmode by holding # down
Type 0205# - get answer (eg. 75)
Type 0205075# (just write the same value again)
Type 01# (to leave test mode)
The phone still says "phone failure..."
Turn phone off and on again - "Insert SIM" DONE!!!
3.
Put test card into your phone and type:
1. 0200# (if the value is different like 124)
you must go to step 2
2. 0200124#
thats all
I dont have tested it. Buth write for results.
unidencek
07-28-2001, 18:07
I have t260 GPRS with tamper alert.
I ll try to fix it this evening.
and
DONT UNLOCK T260 GPRS with standard roemmi box. it goes tamper alert
bye jure
westerna
07-31-2001, 19:17
If you want to repair your the latest versions of Motorola from or to unlock it, come here <a href="http://westerna.org" target="_blank">http://westerna.org</a> for more information.
<br />Best Regards,<br />Westerna<br /><a href="http://westerna.org" target="_blank">http://westerna.org</a>
hey westerna <img src="wink.gif" border="0"><br />Do you sell emmi clips? and if yes, how much? mail me privatly.
BR
hanskemp@planet.nl
08-01-2001, 08:04
All 3 methods not working to remove yamper alert<br />regards Hans
Dubpoison
08-01-2001, 22:37
HiZ!<br />The only way to know the phone version is thought test card or there is another way to know it???
Regards<br />DUBPOISON
Hi
The only way is testcard comand 19#
But you can made easy from "goldwafercard" card is PIC 16F84 and 24LC16, but the 24LC16 is not needed. Program it with Ludipipo or simelar programmer ( is very cheap, only 6 parts ), ponyprog ( <a href="http://www.lancos.com" target="_blank">www.lancos.com</a> )work too.<br />Use testcard.hex from ronny stern, cut simcard to plug in size and thats it's.
Wafercard 10$<br />parts for programmer 2$<br />Simcardsocket for programm, just use an from a old phone, or buy a new creditcardsize holder for 7$
If anyone need more help, just ask here.
Jan
The best universal box <a href="http://www.jimlovell.de" target="_blank">www.jimlovell.de</a>
Where can I buy these wafercards?
Thanks in advance!
Hi
I have only German adress, but look at Satshops, say used also as pay TV cards.<br />In Germany <a href="http://www.viseoduck.de" target="_blank">www.viseoduck.de</a>
Jan
HI ASAS,
<br />i tested your solution. But tested you tested this procedure or no ???
I haw at this moment none phone for testing unlock with roemmi, but when i have then i tested.
Thanx for ide !
Orbital GSM
<a href="http://www.odblokovani.aktualne.cz" target="_blank">My Unlock Info Page</a>
[ 02 August 2001: Message edited by: Orbital GSM ]</p>
I dont have tested this solutions for repairing!!!!<br />Sou dont unlock new versions with roemmi!
eternity
08-14-2001, 01:02
he he he ...
i use patched firmware for emmi 2d and downgrade motorola ...
then with flexing correct eeprom and unlock it without problems ...
Some firmwares from CHina (named Repair firmware) contains eeprom section also ..)
P.S. On totaly dead motorolas must use JTAG interface from emmi to flash it ... AND RETURN FROM DARKNESS
I can (and many people here) to return the <br />deads from the darkness with regular Emmi2d..<br />One thing, it need to open the phone..<br />But connecting the JTAG interface required<br />the case opening too 8-)
<br />WBR<br />Crew
<br /> [quote]Originally posted by Victor Levunliev:<br /><strong>he he he ...
i use patched firmware for emmi 2d and downgrade motorola ...
then with flexing correct eeprom and unlock it without problems ...
Some firmwares from CHina (named Repair firmware) contains eeprom section also ..)
P.S. On totaly dead motorolas must use JTAG interface from emmi to flash it ... AND RETURN FROM DARKNESS</strong><hr></blockquote>
eternity
08-14-2001, 02:00
Hi Crew ...
yes! u are right ... but be cool to do not receive error "Part Identifier = 0000" everey time when u try to downgrade ... simple from C4_13_03 to C4_10_75...
;-)
You just forgot about "test point" , buddy 8-)
WBR<br />Crew
[quote]Originally posted by Victor Levunliev:<br /><strong>Hi Crew ...
yes! u are right ... but be cool to do not receive error "Part Identifier = 0000" everey time when u try to downgrade ... simple from C4_13_03 to C4_10_75...
;-)</strong><hr></blockquote>