k800 after change flash ic how to flash ...?

[jimmyyew1981]

any one can teach me step by step to flash the phone after change flash ic?

[GSM Dream]

Hello!
1. Turn the phone into "Security Bypass" state (by testpoints).
2. Write fullflash/gdfs.
3. Perform "Unlock and Repair GDFS Security Blocks" operation.
4. Write main/FS/cust. pack
That's all.

[sottel]

this method is bad. check for W850 and K800!!!

[peter002]

значит метод такой.

1. берём новую или б/у флешку.
2. заливаем в неё на программаторе fullflash от DreamBox
3. через testpoints делаем Security Bypass
4. через Security Bypass заливаем fullflash
5. через Security Bypass заливаем gdfs
6. далее через Security Bypass делаем Unlock and Repair GDFS Security Blocks
7. через Normal заливаем main и FS и cust
8. готово
man, i think u know better the rules of he forum.. the post made by u cud hlp me a lot if u'd hav posted in english.. plz use english language broo.
thanx

[megah01]

--- Security Bypass------------------------------------------------------------
User selected phone W610 using Test Point boot mode
Stage 1 started
1) Turn OFF the phone.
2) Connect the phone to DreamBox cable.
Boot Responce = 5A
Processor ID = 99000301FFFFFFFF (DB2020 / DB2030)
NOR Flash ID = 897E
OTP Status = LOCKED
OTP IMEI = 357154-01-803999-4
OTP CID = 52
EROM Color = 4 : RED
EROM CID = 52
Hint : Now the probe might be disconnected
Processing ...
Stage 1 completed succesfully
Stage 2 start
Hint : Now the probe might be disconnected
Processing...
Entering Security Bypass mode ...
1) Turn OFF the phone.
2) Connect the phone to DreamBox cable.
Boot Responce = 5A
Processor ID = 99000301FFFFFFFF (DB2020 / DB2030)
Sending Application ...
NOR Flash ID = 897E
OTP Status = LOCKED
OTP IMEI = 357154-01-803999-4
OTP CID = 52
EROM Color = 4 : RED
EROM CID = 52
Baseband Chip ID = 9900
Phone ID = 2480227315F049C4
Finalizing ...
Stage 2 completed succesfully
Done.
--- Loading flash file---------------------------------------------------------
Loading "E:\dari F\Dream box\Dreambox SE\__fullflash\W610_full_OTP-CID51_EROM-CID52_ST.bin"...
Done.
--- Write Flash----------------------------------------------------------------
User selected phone W610 using Security Bypass boot mode
1) Turn OFF the phone.
2) Connect the phone to DreamBox cable.
Boot Responce = 5A
Processor ID = 99000301FFFFFFFF (DB2020 / DB2030)
Sending Application ...
NOR Flash ID = 897E
OTP Status = LOCKED
OTP IMEI = 357154-01-803999-4
OTP CID = 52
EROM Color = 4 : RED
EROM CID = 52
Baseband Chip ID = 9900
Phone ID = 2480227315F049C4
Flash Chip : Intel 48F50xxM0Y0
Flash Chip ID : 887E0089
Writing ...
Error : Failed.




how about this????

[GSM Dream]

Hello!
Low phone battery or this is hardware issue.

[jimmyyew1981]

Hello!
1. Turn the phone into "Security Bypass" state (by testpoints).
2. Write fullflash/gdfs.
3. Perform "Unlock and Repair GDFS Security Blocks" operation.
4. Write main/FS/cust. pack
That's all.




need to write imei????

[GSM Dream]

DBSS will ask you to enter IMEI.