View Full Version : Thouch screen cilibration problem
farihabest
03-07-2009, 05:40
dear friends....salam..
I am inifinty box user and love this box too much.
but there is one problem that i facing in chines miracle with touch screen.
when i get pinout then i connect it to inifinity box. I format the phone with complete mode because it does not formt with safemode.
After format with complete mode it brings touch screen section and do not go forward. it say to me test touch screen celebration and say to touch right, left etc and does not go forward.
what is the solution?
I face this problem often in those chines miracle which support touch screen celibration.
I also do the "touch screen celibration" with mode 1,2,3 and for but it does not works and gives error "operation failed"
I also download new firmware form support area but the probleme is same..
some body give me the solution
thanks in advance
InfinityHelp
03-07-2009, 21:32
hello!
do you use pinfinder?
GSM-DOCTOR
03-07-2009, 21:57
use infinity
connect your phone and from service TAB click on callibration touchscreen button
all will be okay
WBR
G S M - D O C T O R
farihabest
03-08-2009, 05:37
yes yes yes yes.....I use pnifinder with nifinity box but often touch screen sets does not format with safe mode. and if I flash or format with complete mode I face touch screen problem and can not be solved with touch screen celibration button in 1,2,3,4 or 5 mode..
thanks for responce ...
salmanafzal
03-08-2009, 06:45
dear dont relealse power button till it completed sure it will done
farihabest
03-08-2009, 07:25
I am not releasing the power button....
InfinityHelp
03-09-2009, 00:03
hello!
i must admit that sometimes pinfindr power is not enough to power On phone complitely.
this is why test mode operations failing.
please measure voltage on pinfinder output, if it is less than 5.00 volts (phone not connected)
then you must remove limiting diode in main infinity box
farihabest
03-09-2009, 06:11
hello!
i must admit that sometimes pinfindr power is not enough to power On phone complitely.
this is why test mode operations failing.
please measure voltage on pinfinder output, if it is less than 5.00 volts (phone not connected)
then you must remove limiting diode in main infinity box
yes yes...thats problem....It says that test mode failed...
So is there any solution for increase voltage....I afraid if i open the infinity box I shall damage.. which is be loved to me.....(Infinity the best)
can you give me any wanranty to that box if I damaged?..
thanks for solution.....I was very very upsat for that problem.....
because when ever I format any touchscreen mobile it gives me touchscreen problem and when i try to remove the problem with celibration modes...first it connects then give me test mode faild..
thanks..thanks...thanks..
INFINITY TEAM PLS SHOW PICTURE ,to remove diode
farihabest
03-10-2009, 06:52
dear infinit team..
I have increase the power to chines mobile with power supply with 3.7 and it s the correct voltage to a mobile. But It does not detect with pinfinder instead of pinfinder power.
should i give only pinfinder power or can be given with power supply?
farihabest
03-10-2009, 07:42
this is my logs when i am trying to remove tochscreen problem.
I do not release the power button.
I have connected the power cabel of infinity pinfinder
++++++++++++++++++++++++++++++++++++++++++++
COM3 [VCP0] selected
module v2.78
Action: touchscreen calibration
mode: 1
Model: Autodetect 6205-6227 NOR
Checking data, wait...
Phone should be Switched OFF !
Press and HOLD Power button now !
19200 autodetect
Initializing [6226:8A02:8A01]...
CPU: MT6226
high speed boot Off
chip: 0031:8541:C684
status: FF
Connecting at 19200, wait...
error: can not finalize test mode
repeat operation and HOLD phone "Power" button long time !
error: operation failed !
Finished, time used: 75 sec
Remove/Install battery now
+++++++++++++++++++++++++++++++++++++++++++++
I have china T68 firmware (QVGA_PCB01_GPRS_MT6226_S01.SC_7787_129JBO_CSTAR_E N_ARAB_V1_3_26B_20071228_16m_En_Ar.B0M). I flash it all QVGA firmwares. But 3 firmware (QVGA_PCB01_GPRS_MT6226_S01.SC_7787) is flashed set is on but touch screen celibration" not don. I used manval touch screen and all mode in software but no way. pls halp me . thanks
InfinityHelp
03-10-2009, 12:37
this is my logs when i am trying to remove tochscreen problem.
I do not release the power button.
I have connected the power cabel of infinity pinfinder
++++++++++++++++++++++++++++++++++++++++++++
COM3 [VCP0] selected
module v2.78
Action: touchscreen calibration
mode: 1
Model: Autodetect 6205-6227 NOR
Checking data, wait...
Phone should be Switched OFF !
Press and HOLD Power button now !
19200 autodetect
Initializing [6226:8A02:8A01]...
CPU: MT6226
high speed boot Off
chip: 0031:8541:C684
status: FF
Connecting at 19200, wait...
error: can not finalize test mode
repeat operation and HOLD phone "Power" button long time !
error: operation failed !
Finished, time used: 75 sec
Remove/Install battery now
+++++++++++++++++++++++++++++++++++++++++++++
hello!
pinfinder is used or own direct cable?
InfinityHelp
03-10-2009, 12:47
I have china T68 firmware (QVGA_PCB01_GPRS_MT6226_S01.SC_7787_129JBO_CSTAR_E N_ARAB_V1_3_26B_20071228_16m_En_Ar.B0M). I flash it all QVGA firmwares. But 3 firmware (QVGA_PCB01_GPRS_MT6226_S01.SC_7787) is flashed set is on but touch screen celibration" not don. I used manval touch screen and all mode in software but no way. pls halp me . thanks
hello!
this firmware is tested?
flashfiles/ChineseMiracle/_MT6226/QVGA_PCB01_GPRS_MT6226_S01.SC_7787_129JBO_CSTAR_EN _ARAB_V1_3_26B_20071228_16m_En_Ar.B0M.bin
farihabest
03-10-2009, 18:14
I am using rj45 power cable that have been given by the dealer with infinity pinfinder
hello!
i must admit that sometimes pinfindr power is not enough to power On phone complitely.
this is why test mode operations failing.
please measure voltage on pinfinder output, if it is less than 5.00 volts (phone not connected)
then you must remove limiting diode in main infinity box
Hello Sir,
can you give picture of these diodes
br,
InfinityHelp
03-11-2009, 22:58
Hello Sir,
can you give picture of these diodes
br,
hello!
pictures are given in pinfinder user manual which is available for download here:
http://www.infinity-box.biz/download/public/Infinity-Box_PinFinder.pdf
Miftahudin
03-12-2009, 17:17
hello!
pictures are given in pinfinder user manual which is available for download here:
http://www.infinity-box.biz/download/public/Infinity-Box_PinFinder.pdf
yes 100% working.......read page number 20 of this manual