PDA

View Full Version : FLY SLT100 + Black screen after flash

rodriges
03-12-2009, 18:08
COM8 [VCP0] selected
module v2.67
Device: Fly-SLT100
Checking data, wait...
Action: write NAND flash
read mode: 01
"format ffs" active
write: Firmware
skip: Customization/Language Pack
skip: Customization
skip: Eeprom/ffs
source data: page only
identification#1 protocol ver: 04
ver. sw 1: SLT100_HMERID_PCB04_GPRS_MT6228_S02.MAUI_06A_W06_3 6_MP_V36.BIN
ver. sw 2: MAUI.06A.W06.36.MP.V36, 00000000
ffs offset/size: 02000000/02000000
id-page1 Ok
end mark #1 found
nfi area detection finished: Ok
Boot ...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing [6228:8A02:8A02]...
CPU: MT6228
chip: 0031:0000:0101
status: FF
boot packet size: 0400
Release Power button now !
Boot Done
Initialize ...
version: 3.0207
loader: 3.748.0
NAND: Hynix HY27XS08121M 512+16 32 pages, 66Mb
NAND id: AD76AD76
page size: 200+10
pages/block: 20
bits i/o: 08
address cycles: 04
blocks: 1000
ram size: 00800000
NOR: 0000:000000000000 [00000000]
NAND: 00AD:007600AD0076 [04200000]
NOR chip is not installed
Initialize Done
Set baud ...
115200
Set baud Done
Identification ...
reading bootloader structure area...
detecting bootloader structure...
source data: page only
identification#1 protocol ver: 04
ver. sw 1: SLT100_HMERID_PCB04_GPRS_MT6228_S02.MAUI_06A_W06_3 6_MP_V36.BIN
ver. sw 2: MAUI.06A.W06.36.MP.V36, 00000000
ffs offset/size: 02000000/02000000
id-page1 Ok
nfi area detection finished: Ok
identification#1 structure: 2nd [standard] generation
identification#1 detection finished
Identification Done
Write ...
write core area 1 of 2...
write core area 2 of 2...
formatting...
.................................................. .................................................. Write Done
Finished, time used: 2291 sec
Remove/Install battery now !


Hi i used all flashfiles one by one from support but i still have black screen. Phone had to be unlocked but i couldnt do it normal way so thats why i flashed it. Any advice? thx
gsmxpert
03-12-2009, 18:16
bro the file in support having hummer on it is tested and confirmed working....
rodriges
03-12-2009, 18:18
Like i said on my 1st post I used 4 of them one by one . And any of them didnt work. Any further solution for that phone? Thx
InfinitySupport
03-12-2009, 20:39
Hello,

It may be firmware <-> hardware incompatibility.
You can try to use Fly-SX210 flash files too.

Do you have original full flash backup ?
rodriges
03-12-2009, 22:23
Unfortunately i dont! Because i done 4 of those models before and never had any problems thats why i havent done backup this time :-( I will try that cross flash and report. Thx for answer
rodriges
03-13-2009, 01:57
Mission acomplished ;-) For anyone looking for answer about this model . Yes u can flash-cross ur fly SLT100 with flashes from FLY SX210. In my subject flash nr 3 worked fine from support. After so many flashes used to revive this model(spend all day doing this because its a long process) SX210 Flash worked fine :-) Just rememer to restore ur imei to default. THX infinity support