5310 RM-217 no flash file from support site

[EngrRML]

Hello InfinitySuppport,

I need your assistance with this unit 5310 (RM-217). The phone is totally dead and I can't find the exact flash file for this one. Would you please help with this one... Below are the steps I already tried:

1. Use safe format and there is an error
2. Use the complete format and it completed the process. The problem now is, the phone powers on for a few seconds and it only shows the Nokia logo then it shuts down and you cannot power the unit again. You need to repeat the process again then phone do exactly the same thing. I tried using the repair feature to no avail.

3. Downloaded 4 different flash files from the support site and flash it one at a time to the phone. The unit is alive again but with white screen. I concluded that the flash files are not compatible with the unit.


Here is the exact filename of the flash file.
MT6225_06B_PCB01_GPRS_MT6225_S00.GF5_06B_W07_08_MP _V27

The file has a 9.10MB of filesize. The flash files from the support site have different filesize. Therefore, I concluded they are not compatible with this unit.

I also want to ask the help of other techs who have a good flash file for this unit I just need it badly. Thank you in advance for all of your support.

[InfinityHelp]

hello!

you must tell us phone Original software version.
for this you must open with notepad operation.log file which is located in Chinese Miracle folder.
scrool it from up from end and find First operation with this phone (first format FFS)
date/time stamp can also be helpfull in finding it
there you will see Original software version.

post it here

[EngrRML]

Hi!

Below is the operation log. I think this is the original software version of the unit and the firmware is not yet available from the support area. Hope it helps. Thank you again in adv for your help...

ver. sw 1: MT6225_06B_PCB01_GPRS_MT6225_S00.GF5_06B_W07_08_MP _V27.BIN
ver. sw 2: GF5.06B.W07.08.MP.V27, D2F5D14B


Operation Log:


COM7 [VCP0] selected
module v2.79
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
Action: "format ffs"
Boot ...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing [6225:8A03:8A00]...
CPU: MT6225
high speed boot On
chip: 0001:6B03:0009
status: FF
boot packet size: 0400
Release Power button now !
Boot Done
Initialize ...
detecting chip #00 in region #00...
flash: EC257E25082501:18E59F00000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
detecting chip #01 in region #00...
flash: EC257E25082501:18E59F00000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
detecting chip #02 in region #00...
flash: EC257E25082501:18E59F00000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
detecting chip #03 in region #00...
flash: EC257E25082501:18E59F00000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
number of flash chip/regions detected: 04/01
Initialize Done
Set baud ...
115200
Set baud Done
Initialize bootcode ...
Initialize bootcode Done
Check firmware integrity ...
device parameters autodetection in progress...
detecting chip #00 in region #00...
flash: EC257E25082501:18E59F00000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
detecting chip #01 in region #00...
flash: EC257E25082501:18E59F00000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
it's time to stop: 18F09FE518F09FE518F09FE518F09FE518F09FE518F09FE5
number of flash chip/regions detected: 01/01
total flash region size: 01000000
detect device identification#1...
detection phase #1...
detect device identification#1 finished
identification#1 structure: 2nd [enhanced] generation
security area (code #1) is Ok
security area (code #1) backup saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_security\i d.E853CCE8.[MT6225_06B_PCB01_GPRS_MT6225_S00.GF5_06B_W07_08_MP _V27.BIN_B42E0A2D].rpl
====================
New firmware detected (v.2.79, database date: unknown):
MT6225_06B_PCB01_GPRS_MT6225_S00.GF5_06B_W07_08_MP _V27.BIN

This firmware is missing in support area. If this phone is good and working:

- make "Read full flash" operation
- send "system_log_..." file to support: mt62xx@gmail.com
- send flash backup files to support: mt62xx@gmail.com
- include in your e-mail full text from phone back label (phone name etc.)
====================
identification#1 detection finished
device-id: E853CCE8
identification#1 protocol ver: 04
ver. sw 1: MT6225_06B_PCB01_GPRS_MT6225_S00.GF5_06B_W07_08_MP _V27.BIN
ver. sw 2: GF5.06B.W07.08.MP.V27, D2F5D14B
ffs offset/size: 00E00000/00200000
detect device identification#2...
detection phase #1...
.
detect device identification#2 finished
detecting ffs/eeprom area in 1 chip(s)...
standard ffs/eeprom offset detected: 00E00000
flash: EC257E25082501:18E59F00000000
checking area [00000000]: 00000000-00FFFFFF...
ffs/eeprom found near: 00E00000
detecting ffs/eeprom size...
ffs/eeprom size: 00200000
ffs/eeprom chip: 00
ffs/eeprom area: 00000000:00E00000-00FFFFFF
Check firmware integrity Done
Check firmware content ...
Check firmware content Done
Backup required data ...
flash: EC257E25082501:18E59F00000000
Backup required data Done
Patch required data ...
Patch required data Done
Special operation ...
Special operation Done
Write ...
Write Done
Finalization ...
formatting...
flash: EC257E25082501:18E59F00000000
Finalization Done
file saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_security\s ystem_log_E853CCE8_MT6225_06B_PCB01_GPRS_MT6225_S0 0.GF5_06B_W07_08_MP_V27.BIN_B42E0A2D_20090328-044250.B0X.bin
Finished, time used: 49 sec
Remove/Install battery now !

File system has been modified !
It is need to press and HOLD phone "Power" button
during long time (up to 1 min) to make phone Powered-On !

[InfinityHelp]

hello!
try following file:
[bin] flashfiles/ChineseMiracle/_MT6225/MT6225_06B_PCB01_GPRS_MT6225_S00.GF5_06B_W07_08_MP _V27__Nokia-5310-RH-37_16m_En_Id_Vn_Cn.B0M.bin

[EngrRML]

Hi!

I tried the four flash files below from the support area including the one you have suggested to no avail. The unit will power on but only white screen will appear on its lcd... Any other suggestion? Do you want me to send the origial flash file to mt62xx@gmail.com so they can check on the file and make some repair that will help us for future use?



MT6225_06B_PCB01_GPRS_MT6225_S00.GF5_06B_W07_08_MP _V27_16m_En_Ru_Fr_Th_Ar.B0M.bin
MT6225_06B_PCB01_GPRS_MT6225_S00.GF5_06B_W07_08_MP _V27__Nokia-5310_16m_En_Ru_Fr_Th_Ar.B0M.bin
MT6225_06B_PCB01_GPRS_MT6225_S00.GF5_06B_W07_08_MP _V27__Nokia-5310-RH-37_16m_En_Id_Vn_Cn.B0M.bin
MT6225_06B_PCB01_GPRS_MT6225_S00.GF5_06B_W07_08_MP _V27__Nokia-5310XM_16m_En_Ru_Fr_Th_Ar.B0M.bin

[EngrRML]

Hi, here is the original flash file of 5310 RM-217 that is having a problem. You can now check on it what's causing the problem. Thanks in advance.


http://www.mediafire.com/?4yywyd4enoy


http://www.mediafire.com/file/4yywyd4enoy/flash[MT6225_06B_PCB01_GPRS_MT6225_S00.GF5_06B_W07_08_MP _V27.BIN]_20090327-123241.B0M.bin

[InfinityHelp]

hello!

unfortunately, we can not repair faulty firmware files.
you must find same working phone and read out backup
use it to restore your faulty set.
unfortunately, this is the only left way, if you tried all flash files from support

[EngrRML]

Hi!

Thank you for the assistance and for that information. I just wait for the same unit and do the suggestion you have provided. Thank again... :)

[InfinityHelp]

hello!

if you can get flash backup in bin format i will gladly convert it for you

[EngrRML]

Hi!

Sure, if I'm able to get this kind of flash file, I'll inform you right away. Thanks again!

[EngrRML]

Hi!

I have managed to get a backup file in BIN format. Would you please convert it to BOM.BIN format so I can try it in Infinity? Thanks in adv and heres the link where you can download the file...


http://www.mediafire.com/?sharekey=89fa7c7aef8e2af207258ee67c679e4ae04e75f6 e8ebb871

[InfinitySupport]

Hello,

Your file can not be used due to 2 reasons:
1. it was read from damaged phone, data inside firmware is damaged
2. this type of firmware should be read with Infinity-Box only, we can not create good flash file from backup that was made with other software.

[EngrRML]

Thanks for that info. I'll keep that in mind. So, I guess I'll stick with the first option. Wait for the same unit, create a back-up file and try it on the dead phone. Thanks again.

[mario-bouras]

hello infinity ,

i have a question ,

i have infiniy box with language pack editor . with chinese miracle i read flash files frpm phones. is there a way i can convert the flash bin files to plain bin files because infinity encrypts bin flash and i cant read with hex editor.

thank you

[yawarniazi]

@InfinitySupport

Here is fully working 16MB .BIN file of above mentioned phone.
http://www.4shared.com/file/111190868/399d70a1/MTK_ROMINFO_v04_MT6225_06B_PCB01_GPRS_MT6225_S00GF 5_06B_W07_08_MP_V27.html

Please convert it to Infinity-Box supported format and upload it to support site.

Best Regards!
yawarniazi

[InfinityHelp]

hello!

http://rapidshare.com/files/243488491/MT6225_06B_PCB01_GPRS_MT6225_S00.GF5_06B_W07_08_MP _V27.B0M.bin.html