S320x problem

[usernome]

I flashed it with a simfree file from support and now I got bad IMEI .
I wrote eeprom and the same .
I tried to change IMEI but it gives me something about new version .

Thanx !

[Deepakranasaria]

flash again ur phone and don't use format option

just flash ur phone and check whether it powering or not

it should power on

post reply

[usernome]

I didn't say that the phone doesn't power on .
The phone powers on and got bad IMEI .

unknown firmware, read flash and send to support

That's what I get when I try to change IMEI .
I wrote 2 flash files from support .

Thanx !

[usernome]

So , is there a solution for me ?

[InfinitySupport]

I flashed it with a simfree file from support and now I got bad IMEI .
I wrote eeprom and the same .
I tried to change IMEI but it gives me something about new version .

Thanx !

What was that "something" ?

[usernome]

unknown firmware, read flash and send to support

That was after I wrote the flash file from support ...

[InfinitySupport]

Do you have exact log and error message ?

[usernome]

==== log opened: [4/9/2009 1:32:52 PM] ====
Application: D:\Program Files\InfinityBox\MModule\MModule.exe
Loading data, wait...
[Infinity Box] v2.69
S/N: xxxx:xxxx
Wait...
Device: Alcatel-S320X
Done
Imei 352........... already was repaired: 4/9/2009-1:32:06 PM
Continue with this imei ?

==== log: [4/9/2009 1:33:22 PM] ====
COM4 [VCP3] selected
module v2.69
Device: Alcatel-S320X
Checking data, wait...
advanced flash detection enabled
Action: "repair imei"
new imei: 352...............
Boot ...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing [6223:8A05:8A00]...
CPU: MT6223
chip: 0011:2732:A00C
status: 01
boot packet size: 0400
Release Power button now !
Boot Done
Initialize ...
detecting chip #00 in region #00...
flash: 98000300000000:2AEA0000000000
flash: Toshiba AMD/Fujitsu std [T 0008x004000 007Fx020000] 16Mb
number of flash chip/regions detected: 01/01
Initialize Done
Set baud ...
460800
Set baud Done
Initialize bootcode ...
Initialize bootcode Done
Check firmware integrity ...
detect device identification#1...
detection phase #1...
detect device identification#1 finished
identification#1 structure: 2nd [standard] generation
identification#1 detection finished
identification#1 protocol ver: 05
ver. sw 1: JRD23_07A_PCB01_GPRS_MT6223_S00.MAUI_07A_W07_36_SP 1_V20.BIN
ver. sw 2: MAUI.07A.W07.36.SP1.V20, 00000000
ffs offset/size: 00C00000/00400000
detect device identification#2...
detection phase #1...
detect device identification#2 finished
sim-lock status: disabled
security area (code #3, part #2) calculation...
customization: CH16BJ20
done
flash: 98000300000000:2AEA0000000000
flash: 98000300000000:2AEA0000000000
Write: security area (code #3, part #2)
security area (code #3, part #2) calculation done
security area (code #3, part #1) calculation...
use default security area (code #3, part #1) pattern
..................security area (code #3, part #1) detecting size...
security area (code #3, part #1) detecting parameters...
security area (code #3, part #1) encoding...
done
flash: 98000300000000:2AEA0000000000
flash: 98000300000000:2AEA0000000000
Write: security area (code #3, part #1)
security area (code #3, part #1) calculation done
Check firmware integrity Done
Check firmware content ...
Check firmware content Done
Backup required data ...
flash: 98000300000000:2AEA0000000000
Backup required data Done
Patch required data ...
................................................
................................................
................................................
unknown firmware, read flash and send to support
Patch required data Fail
file saved: D:\Program Files\InfinityBox\MModule\backup_security\system_l og__JRD23_07A_PCB01_GPRS_MT6223_S00.MAUI_07A_W07_3 6_SP1_V20.BIN_FFFFFFFF_20090409-133830.B0X.bin
Finished, time used: 294 sec
Remove/Install battery now !

[usernome]

So , where is the problem ?

Thanx !

[usernome]

I think the problem is :

flash: 98000300000000:2AEA0000000000

[InfinitySupport]

Hello,
What was exact file name that you have used for flashing ?
We need to know exact file name to check what is wrong with this firmware.

[usernome]

I used 2 flashes from the support ?
Can 2 flashes be wrong ?
I tried to flash it with another box and I get "write error" .
I will post the names on monday .

Thanx !

[InfinitySupport]

I used 2 flashes from the support ?
Can 2 flashes be wrong ?
I tried to flash it with another box and I get "write error" .
I will post the names on monday .

Thanx !

Hello,

It may be that 2 files from support area has new structure and as a result we can see problem with imei.
Please, post here exact file names so we will be able to double check it.

[usernome]

S320X-2AKPNL1_XH16AB12_JRD23_07A_PCB01_GPRS_MT6223_S00.M AUI_07A_W07_36_SP1_V20_2008-06-20_En_Fr_Es_It_De_simfree.B0M.bin
S320X-2ATLES1_XH16BJ20_JRD23_07A_PCB01_GPRS_MT6223_S00.M AUI_07A_W07_36_SP1_V20_2008-08-21_En_Cn_Cn_simfree.B0M.bin

These are the files .

Thanx !

[usernome]

So , are the files wrong ?

[usernome]

Hellllloooo ! Is there anybody here ?

[usernome]

Can you help me or not ?
I have the phone for about 1 week .
How much do I have to lie the customer ?

Thanx !

[usernome]

Hellllooooooooo !
Infinity team ???!?!?!?

[usernome]

Infinity team can you help me , please ?

Thanx !

[usernome]

I tried to change IMEI with new version and I got this :

COM4 [VCP0] selected
module v2.71
Device: Alcatel-S320X
Checking data, wait...
advanced flash detection enabled
Action: "repair imei"
new imei: 352395025549682
enhanced security fix enabled
Boot ...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing [6223:8A05:8A00]...
CPU: MT6223
chip: 0011:2732:A00C
status: 01
boot packet size: 0400
Release Power button now !
Boot Done
Initialize ...
detecting chip #00 in region #00...
flash: 98000300000000:2AEA0000000000
flash: Toshiba AMD/Fujitsu std [T 0008x004000 007Fx020000] 16Mb
number of flash chip/regions detected: 01/01
Initialize Done
Set baud ...
460800
Set baud Done
Initialize bootcode ...
Initialize bootcode Done
Check firmware integrity ...
detect device identification#1...
detection phase #1...
detect device identification#1 finished
identification#1 structure: 2nd [standard] generation
identification#1 detection finished
identification#1 protocol ver: 05
ver. sw 1: JRD23_07A_PCB01_GPRS_MT6223_S00.MAUI_07A_W07_36_SP 1_V20.BIN
ver. sw 2: MAUI.07A.W07.36.SP1.V20, 00000000
ffs offset/size: 00C00000/00400000
detect device identification#2...
detection phase #1...
detect device identification#2 finished
sim-lock status: disabled
security area (code #3, part #2) calculation...
customization: CH16AB12
done
flash: 98000300000000:2AEA0000000000
flash: 98000300000000:2AEA0000000000
Write: security area (code #3, part #2)
security area (code #3, part #2) calculation done
security area (code #3, part #1) calculation...
use default security area (code #3, part #1) pattern
..................counter: 01
security area (code #3, part #1) detecting size...
security area (code #3, part #1) detecting parameters...
security area (code #3, part #1) encoding...
done
flash: 98000300000000:2AEA0000000000
flash: 98000300000000:2AEA0000000000
Write: security area (code #3, part #1)
security area (code #3, part #1) calculation done
Check firmware integrity Done
Check firmware content ...
Check firmware content Done
Backup required data ...
flash: 98000300000000:2AEA0000000000
Backup required data Done
Patch required data ...
................................................
................................................
................................................
unknown firmware, read flash and send to support
Patch required data Fail
file saved: D:\Program Files\InfinityBox\MModule\backup_security\Alcatel-S320X_JRD23_07A_PCB01_GPRS_MT6223_S00.MAUI_07A_W07 _36_SP1_V20__system_log__FFFFFFFF_20090423-125822.B0X.bin
Finished, time used: 290 sec
Remove/Install battery now !

And this is with firmware and eeprom written from support .

Thanx !

[usernome]

What should I do Infinity team ?

Thanx !

[usernome]

Infinity team , what should I do so you answer me ?

Thanx !

[InfinityHelp]

Infinity team , what should I do so you answer me ?

Thanx !

hello!

try latest MModule 2.72 and post result

[usernome]

COM4 [VCP0] selected
module v2.72
Device: Alcatel-S320X
Checking data, wait...
advanced flash detection enabled
Action: "repair imei"
new imei: 352395025549682
enhanced security fix enabled
Boot ...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing [6223:8A05:8A00]...
CPU: MT6223
chip: 0011:2732:A00C
status: 01
boot packet size: 0400
Release Power button now !
Boot Done
Initialize ...
detecting chip #00 in region #00...
flash: 98000300000000:2AEA0000000000
flash: Toshiba AMD/Fujitsu std [T 0008x004000 007Fx020000] 16Mb
number of flash chip/regions detected: 01/01
Initialize Done
Set baud ...
460800
Set baud Done
Initialize bootcode ...
Initialize bootcode Done
Check firmware integrity ...
detect device identification#1...
detection phase #1...
detect device identification#1 finished
identification#1 structure: 2nd [standard] generation
identification#1 detection finished
identification#1 protocol ver: 05
ver. sw 1: JRD23_07A_PCB01_GPRS_MT6223_S00.MAUI_07A_W07_36_SP 1_V20.BIN
ver. sw 2: MAUI.07A.W07.36.SP1.V20, 00000000
ffs offset/size: 00C00000/00400000
detect device identification#2...
detection phase #1...
detect device identification#2 finished
sim-lock status: disabled
security area (code #3, part #2) calculation...
customization: CH16AB12
done
flash: 98000300000000:2AEA0000000000
flash: 98000300000000:2AEA0000000000
Write: security area (code #3, part #2)
security area (code #3, part #2) calculation done
security area (code #3, part #1) calculation...
use default security area (code #3, part #1) pattern
..................counter: 01
security area (code #3, part #1) detecting size...
security area (code #3, part #1) detecting parameters...
security area (code #3, part #1) encoding...
done
flash: 98000300000000:2AEA0000000000
flash: 98000300000000:2AEA0000000000
Write: security area (code #3, part #1)
security area (code #3, part #1) calculation done
Check firmware integrity Done
Check firmware content ...
Check firmware content Done
Backup required data ...
flash: 98000300000000:2AEA0000000000
Backup required data Done
Patch required data ...
................................................
................................................
................................................
unknown firmware, read flash and send to support
Patch required data Fail
file saved: D:\Program Files\InfinityBox\MModule\backup_security\Alcatel-S320X_JRD23_07A_PCB01_GPRS_MT6223_S00.MAUI_07A_W07 _36_SP1_V20__system_log__FFFFFFFF_20090429-123550.B0X.bin
Finished, time used: 289 sec
Remove/Install battery now !




The same !!!

[usernome]

Can you check this model please ? (flash chip I think) ...

[InfinitySupport]

Hello,

Sorry for delay, programmers is working about this model new hardware type.

[usernome]

I'll wait for the update .

Thanx !

[usernome]

Any news ?????????????????????

[usernome]

The last update didn't work ...

[akhil_bbsr]

Press and HOLD Power button now !
baud autodetection active
19200 autodetect
Connecting, wait...
Initializing [6223:8A05:8A00]...
CPU: MT6223
chip: 0011:0CB6:A00C
status: 01
boot packet size: 0400
Release Power button now !
Boot Done
Initialize ...
detecting chip #00 in region #00...
flash: 98004900000002:2AEA0000000000
flash: Toshiba AMD/Fujitsu std [T 0008x002000 00FFx010000] 16Mb
number of flash chip/regions detected: 01/01
Initialize Done
Set baud ...
460800
Set baud Done
Initialize bootcode ...
Initialize bootcode Done
Check firmware integrity ...
detect device identification#1...
detection phase #1...
detect device identification#1 finished
identification#1 structure: 2nd [standard] generation
identification#1 detection finished
identification#1 protocol ver: 05
ver. sw 1: JRD23_07A_PCB01_GPRS_MT6223_S00.MAUI_07A_W07_36_SP 1_V20.BIN
ver. sw 2: MAUI.07A.W07.36.SP1.V20, 00000000
ffs offset/size: 00C00000/00400000
detect device identification#2...
detection phase #1...
detect device identification#2 finished
sim-lock status: enabled
security area (code #3, part #2) calculation...
customization: CH16DD32
done
flash: 98004900000002:2AEA0000000000
flash: 98004900000002:2AEA0000000000
Write: security area (code #3, part #2)
security area (code #3, part #2) calculation done
security area (code #3, part #1) calculation...
use default security area (code #3, part #1) pattern
..................security area (code #3, part #1) detecting size...
security area (code #3, part #1) detecting parameters...
security area (code #3, part #1) encoding...
done
flash: 98004900000002:2AEA0000000000
flash: 98004900000002:2AEA0000000000
Write: security area (code #3, part #1)
security area (code #3, part #1) calculation done
Check firmware integrity Done
Check firmware content ...
Check firmware content Done
Backup required data ...
flash: 98004900000002:2AEA0000000000
Backup required data Done
Patch required data ...
Patch required data Done
Special operation ...
Special operation Done
Write ...
Write Done
Finalization ...
Finalization Done
file saved: C:\Program Files\InfinityBox\MModule\backup_security\Alcatel-S320X_JRD23_07A_PCB01_GPRS_MT6223_S00.MAUI_07A_W07 _36_SP1_V20__system_log__FFFFFFFF_20090508-135536.B0X.bin
Finished, time used: 148 sec
Remove/Install battery now !


STILL PHONE LOCKED I HAVE 5SETS TO UNLOCK ....IF IAM USING FW-SIM FREE...PHONE IS IN BLUE SCREEN ...NO SOUND......AND STILL LOCKED

[usernome]

Did you make another update ?

Thanx !

[InfinitySupport]

Did you make another update ?

Thanx !

Hello,

Sorry for delay, we need some more time.

[usernome]

COM4 [VCP0] selected
module v2.74
Device: Alcatel-S320X
Checking data, wait...
advanced flash detection enabled
Action: "repair imei"
new imei: 352395025549682
Boot ...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing [6223:8A05:8A00]...
CPU: MT6223
chip: 0011:2732:A00C
status: 01
boot packet size: 0400
Release Power button now !
Boot Done
Initialize ...
detecting chip #00 in region #00...
flash: 98000300000000:2AEA0000000000
flash: Toshiba AMD/Fujitsu std [T 0008x004000 007Fx020000] 16Mb
number of flash chip/regions detected: 01/01
Initialize Done
Set baud ...
460800
Set baud Done
Initialize bootcode ...
Initialize bootcode Done
Check firmware integrity ...
detect device identification#1...
detection phase #1...
detect device identification#1 finished
identification#1 structure: 2nd [standard] generation
identification#1 detection finished
identification#1 protocol ver: 05
ver. sw 1: JRD23_07A_PCB01_GPRS_MT6223_S00.MAUI_07A_W07_36_SP 1_V20.BIN
ver. sw 2: MAUI.07A.W07.36.SP1.V20, 00000000
ffs offset/size: 00C00000/00400000
detect device identification#2...
detection phase #1...
detect device identification#2 finished
sim-lock status: disabled
security area (code #3, part #2) calculation...
customization: CH16AB12
done
flash: 98000300000000:2AEA0000000000
flash: 98000300000000:2AEA0000000000
Write: security area (code #3, part #2)
security area (code #3, part #2) calculation done
security area (code #3, part #1) calculation...
use default security area (code #3, part #1) pattern
..................security area (code #3, part #1) detecting size...
security area (code #3, part #1) detecting parameters...
security area (code #3, part #1) encoding...
done
flash: 98000300000000:2AEA0000000000
flash: 98000300000000:2AEA0000000000
Write: security area (code #3, part #1)
security area (code #3, part #1) calculation done
Check firmware integrity Done
Check firmware content ...
Check firmware content Done
Backup required data ...
flash: 98000300000000:2AEA0000000000
Backup required data Done
Patch required data ...
................................................
................................................
................................................
unknown firmware, read flash and send to support
Patch required data Fail
file saved: D:\Program Files\InfinityBox\MModule\backup_security\Alcatel-S320X_JRD23_07A_PCB01_GPRS_MT6223_S00.MAUI_07A_W07 _36_SP1_V20__system_log__FFFFFFFF_20090518-130705.B0X.bin
Finished, time used: 290 sec
Remove/Install battery now !


That's with 2.74 .

Thanx !

[deepakgarg]

COM4 [VCP0] selected
module v2.74
Device: Alcatel-S320X
Checking data, wait...
advanced flash detection enabled
Action: "repair imei"
new imei: 352395025549682
Boot ...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing [6223:8A05:8A00]...
CPU: MT6223
chip: 0011:2732:A00C
status: 01
boot packet size: 0400
Release Power button now !
Boot Done
Initialize ...
detecting chip #00 in region #00...
flash: 98000300000000:2AEA0000000000
flash: Toshiba AMD/Fujitsu std [T 0008x004000 007Fx020000] 16Mb
number of flash chip/regions detected: 01/01
Initialize Done
Set baud ...
460800
Set baud Done
Initialize bootcode ...
Initialize bootcode Done
Check firmware integrity ...
detect device identification#1...
detection phase #1...
detect device identification#1 finished
identification#1 structure: 2nd [standard] generation
identification#1 detection finished
identification#1 protocol ver: 05
ver. sw 1: JRD23_07A_PCB01_GPRS_MT6223_S00.MAUI_07A_W07_36_SP 1_V20.BIN
ver. sw 2: MAUI.07A.W07.36.SP1.V20, 00000000
ffs offset/size: 00C00000/00400000
detect device identification#2...
detection phase #1...
detect device identification#2 finished
sim-lock status: disabled
security area (code #3, part #2) calculation...
customization: CH16AB12
done
flash: 98000300000000:2AEA0000000000
flash: 98000300000000:2AEA0000000000
Write: security area (code #3, part #2)
security area (code #3, part #2) calculation done
security area (code #3, part #1) calculation...
use default security area (code #3, part #1) pattern
..................security area (code #3, part #1) detecting size...
security area (code #3, part #1) detecting parameters...
security area (code #3, part #1) encoding...
done
flash: 98000300000000:2AEA0000000000
flash: 98000300000000:2AEA0000000000
Write: security area (code #3, part #1)
security area (code #3, part #1) calculation done
Check firmware integrity Done
Check firmware content ...
Check firmware content Done
Backup required data ...
flash: 98000300000000:2AEA0000000000
Backup required data Done
Patch required data ...
................................................
................................................
................................................
unknown firmware, read flash and send to support
Patch required data Fail
file saved: D:\Program Files\InfinityBox\MModule\backup_security\Alcatel-S320X_JRD23_07A_PCB01_GPRS_MT6223_S00.MAUI_07A_W07 _36_SP1_V20__system_log__FFFFFFFF_20090518-130705.B0X.bin
Finished, time used: 290 sec
Remove/Install battery now !


That's with 2.74 .

Thanx !
did u read something special in that log like unknown firmware, read flash and send to support

[usernome]

Please let the one who knows what is this to answer .

Thanx !

[deepakgarg]

try to repair imei in mode 2.if failed than flash phone with latest firmware from support area than repair imei.....but make full flash backup for any emergency case

[usernome]

Again , please let a supporter answer !!!

[usernome]

Any news regarding this phone ?

Thanx !

[usernome]

Is there any news ?

Thanx !

[usernome]

Is there any news ?

Thanx !

[usernome]

Is there any news ?

I have the phone for almost a month .

Thanx !

[usernome]

COM4 [VCP0] selected
module v2.77
Device: Alcatel-S320X
Checking data, wait...
advanced flash detection enabled
Action: "repair imei"
new imei: 352395025549682
Boot ...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing [6223:8A05:8A00]...
CPU: MT6223
chip: 0011:2732:A00C
status: 01
boot packet size: 0400
Release Power button now !
Boot Done
Initialize ...
detecting chip #00 in region #00...
flash: 98000300000000:2AEA0000000000
flash: Toshiba AMD/Fujitsu std [T 0008x004000 007Fx020000] 16Mb
number of flash chip/regions detected: 01/01
Initialize Done
Set baud ...
460800
Set baud Done
Initialize bootcode ...
Initialize bootcode Done
Check firmware integrity ...
detect device identification#1...
detection phase #1...
detect device identification#1 finished
identification#1 structure: 2nd [standard] generation
identification#1 detection finished
identification#1 protocol ver: 05
ver. sw 1: JRD23_07A_PCB01_GPRS_MT6223_S00.MAUI_07A_W07_36_SP 1_V20.BIN
ver. sw 2: MAUI.07A.W07.36.SP1.V20, 00000000
ffs offset/size: 00C00000/00400000
detect device identification#2...
detection phase #1...
detect device identification#2 finished
sim-lock status: disabled
security area (code #3, part #2) calculation...
customization: CH16BJ20
done
flash: 98000300000000:2AEA0000000000
flash: 98000300000000:2AEA0000000000
Write: security area (code #3, part #2)
security area (code #3, part #2) calculation done
security area (code #3, part #1) calculation...
use default security area (code #3, part #1) pattern
..................security area (code #3, part #1) detecting size...
security area (code #3, part #1) detecting parameters...
security area (code #3, part #1) encoding...
done
flash: 98000300000000:2AEA0000000000
flash: 98000300000000:2AEA0000000000
Write: security area (code #3, part #1)
security area (code #3, part #1) calculation done
Check firmware integrity Done
Check firmware content ...
Check firmware content Done
Backup required data ...
flash: 98000300000000:2AEA0000000000
Backup required data Done
Patch required data ...
................................................
................................................
................................................
.........................
original data found, method-B
area header mismatch, unknown firmware, read flash and send to support
Patch required data Fail
file saved: D:\Program Files\InfinityBox\MModule\backup_security\Alcatel-S320X_JRD23_07A_PCB01_GPRS_MT6223_S00.MAUI_07A_W07 _36_SP1_V20__system_log__FFFFFFFF_20090622-181204.B0X.bin
Finished, time used: 332 sec
Remove/Install battery now !

I wrote flash and eeprom from site and I still cannot repair IMEI .

Thanx !

[InfinitySupport]

Hello,

Thanks for test report, we will check it ASAP.

[usernome]

Any news ?
Dis you make some improvments ?
Shall I try again ?

Thanx !

[deepakgarg]

Any news ?
Dis you make some improvments ?
Shall I try again ?

Thanx !
did u try with 2.79.........

[usernome]

I wrote again flash and eeprom from support , repaired IMEI and now the phone just blinks .
I repaired security area ... the same .

Thanx !

@deepakgarg
Stop posting please !!!

[InfinitySupport]

I wrote again flash and eeprom from support , repaired IMEI and now the phone just blinks .
I repaired security area ... the same .

Thanx !

It can not be true.
This phone can not be killed permanently.
if phone can not power-on after flash/repair this means that phone hardware is damaged.
Please, check phone hardware.

[usernome]

If I write eeprom without repairing IMEI the phone turns on completely .
So , there is nothing wrong with the phone .

Thanx !

[InfinitySupport]

If I write eeprom without repairing IMEI the phone turns on completely .
So , there is nothing wrong with the phone .

Thanx !

What is the problem for now ?

Is it problem with imei only or you can not make phone alive ?

[usernome]

If the phone has bad IMEI ( I mean with #%@ instead of numbers ) , it won't register to network .
This is the problem ...

PS : the phone is brand new ...

[InfinitySupport]

Hello,

Firmware for new hardware type (new LCD):
S218X-2DALRU1-366_XH36BN11_JRD23_07A_PCB01_GPRS_MT6223_S00.MAUI_ 07A_W07_36_SP1_V20_2008-12-16_En_De_Ru_Bg_Ua_simfree.B0M.bin

Firmware for old firmware type (old LCD):
S320X-2AKPNL1-16E_XH16AB12_JRD23_07A_PCB01_GPRS_MT6223_S00.MAUI_ 07A_W07_36_SP1_V20_2008-06-20_En_Fr_Es_It_De_simfree.B0M.bin

Try to flash these 2 firmware and let's see results.
Please, check imei afetr each flash process.

[usernome]

After the first flash IMEI is the one on the back side :) .
Shall I try second flash , too ?

[usernome]

Now it's asking for network key ...