infinity team please help about touch celebration

[/\/\A/\/| DON]

COM4 selected
module v2.81
Action: touchscreen calibration
mode: 5
Model: Autodetect 6205-6227 NOR
Checking data, wait...
Phone should be Switched OFF !
Press and HOLD Power button now !
19200 autodetect
Initializing [6225:8A03:8A00]...
CPU: MT6225
high speed boot On
chip: 0001:EF03:0009
status: FF
Connecting at 19200, wait...
Release Power button now !
Phone detected, wait...
Hardware: MT6225,E03
Date: 2006.06.14
Version: 1.0
Version: M6225_00J6_HLD2_00_v03
Version: MT6225_GEMINI_HW
detecting structure #2...
5 11 done
67 byte(s) read
imei: 35044801123456
connection Ok
detecting structure #5 (mode-5)...
0 done
214 byte(s) read
reading data #2...
writing data...
verification...
verification Ok
Finished, time used: 11 sec
Remove/Install battery now !


but still on pen celebration

[InfinitySupport]

Hello,

Try to repeat calibration with other modes or with "reverse calibration" mode.

[/\/\A/\/| DON]

Hello,

Try to repeat calibration with other modes or with "reverse calibration" mode.



sir i tried with other all mode and reverse calibration" show (error

[InfinitySupport]

sir i tried with other all mode and reverse calibration" show (error

Hello,

What was the error exactly ?
Please, post here log.

[/\/\A/\/| DON]

sir here is logs i checked after change imei but my problem is not solved


COM4 selected
module v2.81
Action: touchscreen calibration
mode: 4
Calibration order: reverse
Model: Autodetect 6205-6227 NOR
Checking data, wait...
Phone should be Switched OFF !
Press and HOLD Power button now !
19200 autodetect
Initializing [6225:8A03:8A00]...
CPU: MT6225
high speed boot On
chip: 0001:EF03:0009
status: FF
Connecting at 19200, wait...
Release Power button now !
Phone detected, wait...
Hardware: MT6225,E03
Date: 2006.06.14
Version: 1.0
Version: M6225_00J6_HLD2_00_v03
Version: MT6225_GEMINI_HW
detecting structure #2...
5 11 done
67 byte(s) read
imei: 35044801123456
connection Ok
detecting structure #5 (mode-4)...
8 7 3 2error:
detection failed (4 tries)
What to do:
Try another calibration method, if still no luck:
1. make full flash backup for emergency case
2. make "format ffs"
3. Power-On phone
4. Power-Off phone by "Power" button (do NOT remove battery)
5. Repeat "Calibration" operation again
6. if still no luck read full flash and send to support with subject: touchscreen calibration failed
error: can't read required data
error: operation failed !
Finished, time used: 7 sec

[farihabest]

sir here is logs i checked after change imei but my problem is not solved


COM4 selected
module v2.81
Action: touchscreen calibration
mode: 4
Calibration order: reverse
Model: Autodetect 6205-6227 NOR
Checking data, wait...
Phone should be Switched OFF !
Press and HOLD Power button now !
19200 autodetect
Initializing [6225:8A03:8A00]...
CPU: MT6225
high speed boot On
chip: 0001:EF03:0009
status: FF
Connecting at 19200, wait...
Release Power button now !
Phone detected, wait...
Hardware: MT6225,E03
Date: 2006.06.14
Version: 1.0
Version: M6225_00J6_HLD2_00_v03
Version: MT6225_GEMINI_HW
detecting structure #2...
5 11 done
67 byte(s) read
imei: 35044801123456
connection Ok
detecting structure #5 (mode-4)...
8 7 3 2error:
detection failed (4 tries)
What to do:
Try another calibration method, if still no luck:
1. make full flash backup for emergency case
2. make "format ffs"
3. Power-On phone
4. Power-Off phone by "Power" button (do NOT remove battery)
5. Repeat "Calibration" operation again
6. if still no luck read full flash and send to support with subject: touchscreen calibration failed
error: can't read required data
error: operation failed !
Finished, time used: 7 sec



dear brohter....I always face this problem........but solution...is........


repeat the same mode......twice or three time ...
some mode gives error box and after this you can not close the window.Close the windiw in task manager and try again..

I also repair this with many time repeating... do not worry about this... try again and again until it removes.....

[GSM-XPERTS]

yes i am full full agree with farihabest..

[/\/\A/\/| DON]

dear brohter....I always face this problem........but solution...is........


repeat the same mode......twice or three time ...
some mode gives error box and after this you can not close the window.Close the windiw in task manager and try again..

I also repair this with many time repeating... do not worry about this... try again and again until it removes.....



brother i check it many time but my prob is not solved but dont worry customer has gone so next time i think i got it so thanks brother

[ehsas_ghum]

hi brother plz try with old chines miracle bcoz many user face bugs in new 2.81 plz try with 2.73 n then post thanks

[/\/\A/\/| DON]

hi brother plz try with old chines miracle bcoz many user face bugs in new 2.81 plz try with 2.73 n then post thanks



thanks brother next time i check with old version

[shailccna]

yes sir there is bug in 2.80&2.81 so use 2.73

[zeedan]

i have china mobile show ciliriting touch screen show any solution infinity team

[ranagaurav]

new updates is not sucsess about tuch calibration

[InfinityHelp]

i have china mobile show ciliriting touch screen show any solution infinity team

hello!

if you can not calibrate display in ordinary way-
you can bypass it using option "bypass touchscreen calibration"
you must try all available methods (method-1, method-2 etc) until you succeed

[biochemistali]

and more thing to add
this option does not going to repair touch system, only by passing touch checks from the software, so it is better to have all types of touch system that cost s aabpout 3 $ per touch system.
it is not good always to blame the team, one can do the dre to change the touch screen.