Infinity support please help

[surajmobile]

Sir ia am using infinity box since last 2 year it was working fine on all chines mobile .
Nut from last two month i cant repair any chines mobile .
When i formate any mobile formatting complets but mobile dead .

I had tried 24 chines mobiles all mobiles were on and had software fault but after formating all my mobile are dead now .
I had reinstall windows and complete infinity box setup..
I had tried to repair all mobile using "repair software"
but problem same.
Thanks in advance.

[InfinitySupport]

Hello,

What is the problems exactly with each phone ?
Post here operation log.

[surajmobile]

Hello,

What is the problems exactly with each phone ?
Post here operation log.
COM3 [VCP0] selected
module v2.81
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
Action: "format ffs"
Boot ...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing [6225:8A03:8A00]...
CPU: MT6225
high speed boot On
chip: 0001:3603:0005
status: FF
boot packet size: 0400
Release Power button now !
Boot Done
Initialize ...
detecting chip #00 in region #00...
flash: 98000300000000:18A59F00000000
flash: Toshiba AMD/Fujitsu std [T 0008x004000 007Fx020000] 16Mb
detecting chip #01 in region #00...
flash: 98000300000000:18A59F00000000
flash: Toshiba AMD/Fujitsu std [T 0008x004000 007Fx020000] 16Mb
detecting chip #02 in region #00...
flash: 98000300000000:18A59F00000000
flash: Toshiba AMD/Fujitsu std [T 0008x004000 007Fx020000] 16Mb
detecting chip #03 in region #00...
flash: 98000300000000:18A59F00000000
flash: Toshiba AMD/Fujitsu std [T 0008x004000 007Fx020000] 16Mb
number of flash chip/regions detected: 04/01
Initialize Done
Set baud ...
115200
Set baud Done
Initialize bootcode ...
Initialize bootcode Done
Check firmware integrity ...
device parameters autodetection in progress...
detecting chip #00 in region #00...
flash: 98000300000000:18A59F00000000
flash: Toshiba AMD/Fujitsu std [T 0008x004000 007Fx020000] 16Mb
detecting chip #01 in region #00...
flash: 98000300000000:18A59F00000000
flash: Toshiba AMD/Fujitsu std [T 0008x004000 007Fx020000] 16Mb
it's time to stop: 18B09FA518B09FA518B09FA518B09FA518B09FA518B09FA5
number of flash chip/regions detected: 01/01
total flash region size: 01000000
detect device identification#1...
detection phase #1...
.
detection phase #2...
.................................................. .................................................. .................................................. .................................................. .................................................. ......
warning: identification#1 information not found, possible reasons:
.old firmware type w/o identification#1 data
.damaged firmware
.damaged hardware
if phone works fine just ignore this warning
detect device identification#1 finished
detect device identification#2...
detection phase #1...
.
detect device identification#2 finished
detecting ffs/eeprom area in 1 chip(s)...
standard ffs/eeprom offset assigned: 00E00000
flash: 98000300000000:18A59F00000000
checking area [00000000]: 00000000-00FFFFFF...
Can't detect ffs/eeprom area
Do you want to use standard ffs/eeprom address: 00E00000 ?

If you are not sure that standard address is correct:
1. press "NO" and terminate current operation
2. make flash backup for emergency case
3. repeat required operation
standard ffs/eeprom address selected by user
detecting ffs/eeprom size...
ffs/eeprom size: 00200000
ffs/eeprom chip: 00
ffs/eeprom area: 00000000:00E00000-00FFFFFF
Check firmware integrity Done
Check firmware content ...
Check firmware content Done
Backup required data ...
flash: 98000300000000:18A59F00000000
Backup required data Done
Patch required data ...
Patch required data Done
Special operation ...
Special operation Done
Write ...
Write Done
Finalization ...
formatting...
flash: 98000300000000:18A59F00000000
Finalization Done
Finished, time used: 103 sec
Remove/Install battery now !

File system has been modified !
It is need to press and HOLD phone "Power" button
during long time (up to 1 min) to make phone Powered-On !

[surajmobile]

Sir my all 24 mobile have same log which i had shown above but al mobile have same problem they doesn't power on .
Even some of them were on before i formated them


so please solve my problem because i am only based on infinity box.

[InfinityHelp]

hello!

best solution is making full backup before operation.
also, smarter is to make Format FFS safe
only after safe format do not help- proceed to complete format