patelfaizu
05-01-2009, 09:54
sir here is one nokia 1600chines it had flight mode problem then did formet ffs befor that i took bck up but after finish that process now phone is dead
This the bck file of that phoneflash[TOP23_07A_PCB01_GPRS_MT6223P_S00.N1112_V5_53.BIN]_20090430-033411.B0M no1600
N This the eprron
eeprom[TOP23_07A_PCB01_GPRS_MT6223P_S00.N1112_V5_53.BIN]_20090430-035622.B0Eno 1600
but when i m trying to restore that bck up its showing this type error
This the log
==== log: [5/1/2009 12:21:21 AM] ====
COM8 [VCP0] selected
module v2.73
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
Action: write NOR flash
"smart write" active
write: Firmware
skip: Customization/Language Pack
skip: Customization
write: Eeprom/ffs
eeprom backup enabled, it may takes several minutes !
Boot ...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing [6223:8A04:8A00]...
CPU: MT6223
high speed boot On
chip: 0011:B7B3:000C
boot packet size: 0400
Release Power button now !
Boot Done
Initialize ...
detecting chip #00 in region #00...
flash: EC257E25062501:2AEA0000000000
flash: AMD/Fujitsu std [D 0008x002000 007Ex010000 0008x002000] 8Mb
detecting chip #01 in region #00...
flash: EC257E25062501:2AEA0000000000
flash: AMD/Fujitsu std [D 0008x002000 007Ex010000 0008x002000] 8Mb
detecting chip #02 in region #00...
flash: EC257E25062501:2AEA0000000000
flash: AMD/Fujitsu std [D 0008x002000 007Ex010000 0008x002000] 8Mb
detecting chip #03 in region #00...
flash: EC257E25062501:2AEA0000000000
flash: AMD/Fujitsu std [D 0008x002000 007Ex010000 0008x002000] 8Mb
number of flash chip/regions detected: 04/01
Initialize Done
Set baud ...
460800
Set baud Done
Initialize bootcode ...
Initialize bootcode Done
Check firmware integrity ...
device parameters autodetection in progress...
detecting chip #00 in region #00...
flash: EC257E25062501:2AEA0000000000
flash: AMD/Fujitsu std [D 0008x002000 007Ex010000 0008x002000] 8Mb
detecting chip #01 in region #00...
flash: EC257E25062501:2AEA0000000000
flash: AMD/Fujitsu std [D 0008x002000 007Ex010000 0008x002000] 8Mb
it's time to stop: 2A0000EA18F09FE518F09FE518F09FE518F09FE518F09FE5
number of flash chip/regions detected: 01/01
total flash region size: 00800000
detect device identification#1...
detection phase #1...
error: wrong answer: C7
.
detection phase #2...
error: unexpected termination/freez: 00000000
warning: identification#1 information not found, possible reasons:
.old firmware type w/o identification#1 data
.damaged firmware
.damaged hardware
if phone works fine just ignore this warning
detect device identification#1 finished
detect device identification#2...
detection phase #1...
error: unexpected termination/freez: 00000000
warning: optional information is not found,
if phone works well just ignore this warning
detect device identification#2 finished
detecting eeprom/ffs area in 1 chip(s)...
standard eeprom/ffs offset assigned: 00700000
error: no any expected answer
error: no any expected answer : wrong answer after chip id request
error: no any expected answer
error: no any expected answer
error: no any expected answer : wrong answer after chip cfi request
error: no any expected answer
error: no any expected answer : wrong answer after chip id request
Can't detect eeprom/ffs area
Do you want to use standard ffs address: 00700000 ?
If you are not sure that standard address is correct:
1. press "NO" and terminate current operation
2. make flash backup for emergency case
3. repeat required operation
operation terminated by user
error: critical error#1 during ffs size detection
error: can't detect eeprom/ffs address/size
Check firmware integrity Done
Check firmware content ...
Check firmware content Fail
Finished, time used: 203 sec
Remove/Install battery now !
WARNING ! Settings will be cleared, user data erased, Imei set to default value !
Make flash backup before this procedure !
Do you want to continue ?
==== log: [5/1/2009 12:25:38 AM] ====
COM8 [VCP0] selected
module v2.73
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
Action: "format ffs"
Boot ...
Press and HOLD Power button now !
error: can't detect device
Release Power button now !
in case of initial connection problem: on/off "Boot baudrate autoselect"
Boot Fail
Finished, time used: 62 sec
Remove/Install battery now !
WARNING ! Settings will be cleared, user data erased, Imei set to default value !
Make flash backup before this procedure !
Do you want to continue ?
==== log: [5/1/2009 12:27:00 AM] ====
COM8 [VCP0] selected
module v2.73
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
Action: erase flash chip
Boot ...
Press and HOLD Power button now !
error: can't detect device
Release Power button now !
in case of initial connection problem: on/off "Boot baudrate autoselect"
Boot Fail
Finished, time used: 95 sec
Remove/Install battery now !
so sir any solution pls
This the bck file of that phoneflash[TOP23_07A_PCB01_GPRS_MT6223P_S00.N1112_V5_53.BIN]_20090430-033411.B0M no1600
N This the eprron
eeprom[TOP23_07A_PCB01_GPRS_MT6223P_S00.N1112_V5_53.BIN]_20090430-035622.B0Eno 1600
but when i m trying to restore that bck up its showing this type error
This the log
==== log: [5/1/2009 12:21:21 AM] ====
COM8 [VCP0] selected
module v2.73
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
Action: write NOR flash
"smart write" active
write: Firmware
skip: Customization/Language Pack
skip: Customization
write: Eeprom/ffs
eeprom backup enabled, it may takes several minutes !
Boot ...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing [6223:8A04:8A00]...
CPU: MT6223
high speed boot On
chip: 0011:B7B3:000C
boot packet size: 0400
Release Power button now !
Boot Done
Initialize ...
detecting chip #00 in region #00...
flash: EC257E25062501:2AEA0000000000
flash: AMD/Fujitsu std [D 0008x002000 007Ex010000 0008x002000] 8Mb
detecting chip #01 in region #00...
flash: EC257E25062501:2AEA0000000000
flash: AMD/Fujitsu std [D 0008x002000 007Ex010000 0008x002000] 8Mb
detecting chip #02 in region #00...
flash: EC257E25062501:2AEA0000000000
flash: AMD/Fujitsu std [D 0008x002000 007Ex010000 0008x002000] 8Mb
detecting chip #03 in region #00...
flash: EC257E25062501:2AEA0000000000
flash: AMD/Fujitsu std [D 0008x002000 007Ex010000 0008x002000] 8Mb
number of flash chip/regions detected: 04/01
Initialize Done
Set baud ...
460800
Set baud Done
Initialize bootcode ...
Initialize bootcode Done
Check firmware integrity ...
device parameters autodetection in progress...
detecting chip #00 in region #00...
flash: EC257E25062501:2AEA0000000000
flash: AMD/Fujitsu std [D 0008x002000 007Ex010000 0008x002000] 8Mb
detecting chip #01 in region #00...
flash: EC257E25062501:2AEA0000000000
flash: AMD/Fujitsu std [D 0008x002000 007Ex010000 0008x002000] 8Mb
it's time to stop: 2A0000EA18F09FE518F09FE518F09FE518F09FE518F09FE5
number of flash chip/regions detected: 01/01
total flash region size: 00800000
detect device identification#1...
detection phase #1...
error: wrong answer: C7
.
detection phase #2...
error: unexpected termination/freez: 00000000
warning: identification#1 information not found, possible reasons:
.old firmware type w/o identification#1 data
.damaged firmware
.damaged hardware
if phone works fine just ignore this warning
detect device identification#1 finished
detect device identification#2...
detection phase #1...
error: unexpected termination/freez: 00000000
warning: optional information is not found,
if phone works well just ignore this warning
detect device identification#2 finished
detecting eeprom/ffs area in 1 chip(s)...
standard eeprom/ffs offset assigned: 00700000
error: no any expected answer
error: no any expected answer : wrong answer after chip id request
error: no any expected answer
error: no any expected answer
error: no any expected answer : wrong answer after chip cfi request
error: no any expected answer
error: no any expected answer : wrong answer after chip id request
Can't detect eeprom/ffs area
Do you want to use standard ffs address: 00700000 ?
If you are not sure that standard address is correct:
1. press "NO" and terminate current operation
2. make flash backup for emergency case
3. repeat required operation
operation terminated by user
error: critical error#1 during ffs size detection
error: can't detect eeprom/ffs address/size
Check firmware integrity Done
Check firmware content ...
Check firmware content Fail
Finished, time used: 203 sec
Remove/Install battery now !
WARNING ! Settings will be cleared, user data erased, Imei set to default value !
Make flash backup before this procedure !
Do you want to continue ?
==== log: [5/1/2009 12:25:38 AM] ====
COM8 [VCP0] selected
module v2.73
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
Action: "format ffs"
Boot ...
Press and HOLD Power button now !
error: can't detect device
Release Power button now !
in case of initial connection problem: on/off "Boot baudrate autoselect"
Boot Fail
Finished, time used: 62 sec
Remove/Install battery now !
WARNING ! Settings will be cleared, user data erased, Imei set to default value !
Make flash backup before this procedure !
Do you want to continue ?
==== log: [5/1/2009 12:27:00 AM] ====
COM8 [VCP0] selected
module v2.73
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
Action: erase flash chip
Boot ...
Press and HOLD Power button now !
error: can't detect device
Release Power button now !
in case of initial connection problem: on/off "Boot baudrate autoselect"
Boot Fail
Finished, time used: 95 sec
Remove/Install battery now !
so sir any solution pls