error: error# 0000FFFF in imei repair

[gambitjam]

I back up both Full flash & eeprom. After repairing calibration imei needed to be re write. but gives me the below error.
I follow all the instruction to solve this problem but same. Now i can't even flash back the backup flash & eeprom. it will write error.

COM6 [VCP0] selected
module v2.74
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
Action: "repair imei"
imei write method: mode-3
imei write channel: imei #1 for dual sim/mono CPU
new imei: 340460108004040
ffs/eeprom backup enabled, it may takes several minutes !
Boot ...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing [6225:8A05:8A00]...
CPU: MT6225
high speed boot On
chip: 0001:F903:0009
boot packet size: 0400
Release Power button now !
Boot Done
Initialize ...
detecting chip #00 in region #00...
flash: 98000300000000:18E59F00000000
flash: AMD/Fujitsu std [T 0008x004000 007Fx020000] 16Mb
detecting chip #01 in region #00...
flash: 98000300000000:18E59F00000000
flash: AMD/Fujitsu std [T 0008x004000 007Fx020000] 16Mb
number of flash chip/regions detected: 02/01
Initialize Done
Set baud ...
460800
Set baud Done
Initialize bootcode ...
Initialize bootcode Done
Check firmware integrity ...
device parameters autodetection in progress...
detecting chip #00 in region #00...
flash: 98000300000000:18E59F00000000
flash: AMD/Fujitsu std [T 0008x004000 007Fx020000] 16Mb
detecting chip #01 in region #00...
flash: 98000300000000:18E59F00000000
flash: AMD/Fujitsu std [T 0008x004000 007Fx020000] 16Mb
it's time to stop: 18F09FE518F09FE518F09FE518F09FE518F09FE518F09FE5
number of flash chip/regions detected: 01/01
total flash region size: 01000000
detect device identification#1...
detection phase #1...
detect device identification#1 finished
identification#1 structure: 2nd [standard] generation
identification#1 protocol ver: 04
ver. sw 1: HEXING25_GEMINI_PCB01_GPRS_MT6225_S00.B011_2_W08_1 2_01.BIN
ver. sw 2: B011_2.W08.12.01, 00000000
ffs offset/size: 00E00000/00200000
detecting security area (code #2)...
.................................................. .................................................. ............................
security area (code #2) is absent
detect device identification#2...
detection phase #1...
.
detect device identification#2 finished
detecting ffs/eeprom area in 1 chip(s)...
standard ffs/eeprom offset detected: 00E00000
flash: 98000300000000:18E59F00000000
checking area [00000000]: 00000000-00FFFFFF...
ffs/eeprom found near: 00E00000
detecting ffs/eeprom size...
ffs/eeprom size: 00200000
ffs/eeprom chip: 00
ffs/eeprom area: 00000000:00E00000-00FFFFFF
Check firmware integrity Done
Check firmware content ...
Check firmware content Done
Backup required data ...
reading: eeprom[HEXING25_GEMINI_PCB01_GPRS_MT6225_S00.B011_2_W08_1 2_01.BIN]...
file saved: C:\Program Files\InfinityBox\ChineseMiracle\eeprom[HEXING25_GEMINI_PCB01_GPRS_MT6225_S00.B011_2_W08_1 2_01.BIN]_20090528-173435.B0E.bin
flash: 98000300000000:18E59F00000000
Backup required data Done
Patch required data ...
2 step(s) required
Patch required data Done
Special operation ...
Special operation Done
Write ...
flash: 98000300000000:18E59F00000000
Write: eeprom
error: error# 0000FFFF
error: flash write error: 00E00000:00002000
error: error# 0000FFFF
error: flash write error: 00E00000:00002000
error: error# 0000FFFF
error: flash write error: 00E00000:00002000
Write Fail
Finished, time used: 148 sec
Remove/Install battery now !

HELP:mad:

[gambitjam]

This is what is giving me when flashing full backup.

flash write error: 00E00000:00002000
At 87%

[InfinityHelp]

hello!

what cable do you use as interface?
what is phone condition now?

[gambitjam]

hello!

what cable do you use as interface?
what is phone condition now?

The cable is L12C with 1x12 pins
I use pinfinder and got RX=7 TX=6
PHONE NAME = NASAKI NK630

Now the condition of the phone is DEAD.

[gambitjam]

FILE NOT AVAILABLE ON SUPPORT SIDE:
HEXING25_GEMINI_PCB01_GPRS_MT6225_S00.B011_2_W08_1 2_01
:mad:

[InfinityHelp]

hello!

please use lastest chinese miracle module
the one which you using do not support this flash IC

[gambitjam]

hello!

please use lastest chinese miracle module
the one which you using do not support this flash IC

I have been trying to download the main setup but it always break.
I used normal downloading, it will just cut in any percent and show download complete.
I already tried downloading bits by pieces up to five only.
Any problem with the site.

[InfinityHelp]

hello!

latest Chinese Miracle module is available to download separatly.
also, if you still wish to get Main Setup, you can try different mirror servers.
maybe on them you will get better or more stable connection