Please upload fullflash for ZTC N95. Dead after format! Used fullflash from Infinity support-screen didn't show! Thanks.
malpinssa
05-29-2009, 13:03
i dont tank is dead after format it.bro you can try with full batrier .i hope it will be ok
Tried with fully charged battery, the same problem! I can hear the sound of switching on phone, but no screen!
InfinityHelp
05-29-2009, 21:52
hello!
post first formating log.
you can find it in operatio.log file, chinese miracle directory
==== log: [28.05.2009 22:26:20] ====
COM8 [VCP0] selected
module v2.73
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
Action: "format ffs"
Boot ...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing [6226:8A02:8A01]...
CPU: MT6226
high speed boot Off
chip: 0031:B1E4:6A85
high speed boot Off
boot packet size: 0002
Release Power button now !
Boot Done
Initialize ...
detecting chip #00 in region #00...
flash: EC257E25082501:29EA0000000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
detecting chip #01 in region #00...
flash: EC257E25082501:29EA0000000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
number of flash chip/regions detected: 02/01
Initialize Done
Set baud ...
921600
Set baud Done
Initialize bootcode ...
Initialize bootcode Done
Check firmware integrity ...
device parameters autodetection in progress...
detecting chip #00 in region #00...
flash: EC257E25082501:29EA0000000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
detecting chip #01 in region #00...
flash: EC257E25082501:29EA0000000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
it's time to stop: 290000EA18F09FE518F09FE518F09FE518F09FE518F09FE5
number of flash chip/regions detected: 01/01
total flash region size: 01000000
detect device identification#1...
detection phase #1...
detect device identification#1 finished
identification#1 structure: 2nd [enhanced] generation
security area (code #1) is Ok
security area (code #1) backup saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_security\i d.A8A7C180.[E553_XZY1PA_E553_GPRS_MT6226_S01.01_1.BIN_558D361A].rpl
identification#1 detection finished
device-id: A8A7C180
identification#1 protocol ver: 04
ver. sw 1: E553_XZY1PA_E553_GPRS_MT6226_S01.01_1.BIN
ver. sw 2: E553_XZY1PA.01.1, E5C972AA
ffs offset/size: 00800000/001FF000
detect device identification#2...
detection phase #1...
.
warning: optional information is not found,
if phone works well just ignore this warning
detect device identification#2 finished
detecting eeprom/ffs area in 1 chip(s)...
standard eeprom/ffs offset detected: 00800000
flash: EC257E25082501:29EA0000000000
checking area [00000000]: 00000000-00FFFFFF...
eeprom/ffs found near: 00E00000
Detected eeprom/ffs address is non-standard: 00E00000
Posible reasons:
1. eeprom is Ok but address is non-standard
2. eeprom damaged and can't be detected
3. eeprom is Ok but detected incorrectly (f.e. unknown eeprom structure)
If you are not sure that detected address is correct:
1. press "NO" (and select standard address or terminate current operation)
2. make flash backup for emergency case
3. repeat required operation
Are you sure that detected eeprom address is correct ?
Do you want to use standard eeprom address: 00800000 ?
If you are not sure that standard address is correct:
1. press "NO" and terminate current operation
2. make flash backup for emergency case
3. repeat required operation
terminated by user
error: critical error#1 during ffs size detection
error: can't detect eeprom/ffs address/size
Check firmware integrity Done
Check firmware content ...
Check firmware content Done
Backup required data ...
flash: EC257E25082501:29EA0000000000
Backup required data Done
Patch required data ...
Patch required data Done
Special operation ...
Special operation Done
Write ...
Write Done
Finalization ...
formatting...
flash: EC257E25082501:29EA0000000000
Finalization Done
file saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_security\s ystem_log_A8A7C180_E553_XZY1PA_E553_GPRS_MT6226_S0 1.01_1.BIN_558D361A_20090528-223043.B0X.bin
Finished, time used: 247 sec
Remove/Install battery now !
File system has been modified !
It is need to press and HOLD phone "Power" button
during long time (up to 1 min) to make phone Powered-On !
==== log: [28.05.2009 22:34:50] ====
COM8 [VCP0] selected
module v2.73
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
Action: repair security area
Boot ...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing [6226:8A02:8A01]...
CPU: MT6226
high speed boot Off
chip: 0031:B1E4:6A85
high speed boot Off
boot packet size: 0002
Release Power button now !
Boot Done
Initialize ...
detecting chip #00 in region #00...
flash: EC257E25082501:FFFFFF00000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
detecting chip #01 in region #00...
flash: EC257E25082501:FFFFFF00000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
number of flash chip/regions detected: 02/01
Initialize Done
Set baud ...
921600
Set baud Done
Initialize bootcode ...
Initialize bootcode Done
Check firmware integrity ...
device parameters autodetection in progress...
detecting chip #00 in region #00...
flash: EC257E25082501:FFFFFF00000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
Warning: probably flash chip empty, erased, incorrectly flashed or damaged.
What to do:
1. go to software "Settings" page
2. set "Advanced chip detection method" box UN-CHECKED !
3. make flash write operation
If still no luck: send mail to support (mt62xx@gmail.com) with detailed description of problem,
attach the next files in your e-mail:
1. C:\Program Files\InfinityBox\ChineseMiracle\operation.log
2. C:\Program Files\InfinityBox\ChineseMiracle\cfi_xxxx_xxxx.bin
detecting chip #01 in region #00...
flash: EC257E25082501:FFFFFF00000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
it's time to stop: FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF
number of flash chip/regions detected: 01/01
total flash region size: 01000000
detect device identification#1...
detection phase #1...
.
detection phase #2...
.................................................. .................................................. ............................
warning: identification#1 information not found, possible reasons:
.old firmware type w/o identification#1 data
.damaged firmware
.damaged hardware
if phone works fine just ignore this warning
detect device identification#1 finished
detecting security area (code #2)...
.................................................. .................................................. ............................
security area (code #2) is absent
detect device identification#2...
detection phase #1...
.
warning: optional information is not found,
if phone works well just ignore this warning
detect device identification#2 finished
Check firmware integrity Done
Check firmware content ...
Check firmware content Done
Backup required data ...
flash: EC257E25082501:FFFFFF00000000
Backup required data Done
Patch required data ...
Patch required data Done
Special operation ...
Special operation Done
Write ...
Write Done
Finalization ...
Finalization Done
Finished, time used: 181 sec
Remove/Install battery now !
==== log opened: [28.05.2009 22:42:15] ====
Application: C:\Program Files\InfinityBox\ChineseMiracle\ChineseMiracle.ex e
Loading data, wait...
[Infinity Box] v2.73
S/N: 66C4:0112
Wait...
Device: Autodetect 6205-6227 NOR
Done
==== log opened: [28.05.2009 22:42:44] ====
Application: C:\Program Files\InfinityBox\ChineseMiracle\ChineseMiracle.ex e
Loading data, wait...
[Infinity Box] v2.73
S/N: 66C4:0112
Wait...
Device: Autodetect 6205-6227 NOR
Done
Action: read information
Model: Autodetect 6205-6227 NOR
Checking data, wait...
Phone should be Switched ON !
Connecting, wait...
baud set to: 19200
error: connection failed !
operation failed !
Finished, time used: 78 sec
Power off phone now !
Loading file v.02...
ZTC-N95_LEDA26_06A_PCB01_GPRS_MT6226_S01.MAUI_06A_W06_ 48_12_16m_En_Ru_Fr_Th_Vn_Ar.B0M.htm loaded
identification#1 protocol ver: 05
ver. sw 1: LEDA26_06A_PCB01_GPRS_MT6226_S01.MAUI_06A_W06_48_1 2.BIN
ver. sw 2: MAUI.06A.W06.48.12, 2EAF2D75
Loaded file w/protection: security area (code #1)
==== log: [28.05.2009 22:45:51] ====
COM8 [VCP0] selected
module v2.73
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
Action: write NOR flash
"smart write" active
write: Firmware
skip: Customization/Language Pack
skip: Customization
skip: Eeprom/ffs
eeprom backup enabled, it may takes several minutes !
Boot ...
Press and HOLD Power button now !
error: can't detect device
Release Power button now !
in case of initial connection problem: on/off "Boot baudrate autoselect"
Boot Fail
Finished, time used: 15 sec
Remove/Install battery now !
==== log: [28.05.2009 22:46:31] ====
COM8 [VCP0] selected
module v2.73
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
Action: write NOR flash
"smart write" active
write: Firmware
skip: Customization/Language Pack
skip: Customization
skip: Eeprom/ffs
eeprom backup enabled, it may takes several minutes !
Boot ...
Press and HOLD Power button now !
error: can't detect device
Release Power button now !
in case of initial connection problem: on/off "Boot baudrate autoselect"
Boot Fail
Finished, time used: 15 sec
Remove/Install battery now !
==== log opened: [28.05.2009 22:48:12] ====
Application: C:\Program Files\InfinityBox\ChineseMiracle\ChineseMiracle.ex e
Loading data, wait...
[Infinity Box] v2.73
S/N: 66C4:0112
Wait...
Device: Autodetect 6205-6227 NOR
Done
Loading file v.02...
ZTC-N95_LEDA26_06A_PCB01_GPRS_MT6226_S01.MAUI_06A_W06_ 48_12_16m_En_Ru_Fr_Th_Vn_Ar.B0M.htm loaded
identification#1 protocol ver: 05
ver. sw 1: LEDA26_06A_PCB01_GPRS_MT6226_S01.MAUI_06A_W06_48_1 2.BIN
ver. sw 2: MAUI.06A.W06.48.12, 2EAF2D75
Loaded file w/protection: security area (code #1)
==== log: [28.05.2009 22:48:34] ====
COM8 [VCP0] selected
module v2.73
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
Action: write NOR flash
"smart write" active
write: Firmware
skip: Customization/Language Pack
skip: Customization
skip: Eeprom/ffs
eeprom backup enabled, it may takes several minutes !
Boot ...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing [6226:8A02:8A01]...
CPU: MT6226
high speed boot Off
chip: 0031:B1E4:6A85
high speed boot Off
boot packet size: 0002
Release Power button now !
Boot Done
Initialize ...
detecting chip #00 in region #00...
flash: EC257E25082501:FFFFFF00000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
detecting chip #01 in region #00...
flash: EC257E25082501:FFFFFF00000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
number of flash chip/regions detected: 02/01
Initialize Done
Set baud ...
921600
Set baud Done
Initialize bootcode ...
Initialize bootcode Done
Check firmware integrity ...
device parameters autodetection in progress...
detecting chip #00 in region #00...
flash: EC257E25082501:FFFFFF00000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
Warning: probably flash chip empty, erased, incorrectly flashed or damaged.
What to do:
1. go to software "Settings" page
2. set "Advanced chip detection method" box UN-CHECKED !
3. make flash write operation
If still no luck: send mail to support (mt62xx@gmail.com) with detailed description of problem,
attach the next files in your e-mail:
1. C:\Program Files\InfinityBox\ChineseMiracle\operation.log
2. C:\Program Files\InfinityBox\ChineseMiracle\cfi_xxxx_xxxx.bin
detecting chip #01 in region #00...
flash: EC257E25082501:FFFFFF00000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
it's time to stop: FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF
number of flash chip/regions detected: 01/01
total flash region size: 01000000
detect device identification#1...
detection phase #1...
.
detection phase #2...
.................................................. ...............
warning: identification#1 information not found, possible reasons:
.old firmware type w/o identification#1 data
.damaged firmware
.damaged hardware
if phone works fine just ignore this warning
detect device identification#1 finished
detect device identification#2...
detection phase #1...
.
warning: optional information is not found,
if phone works well just ignore this warning
detect device identification#2 finished
detecting eeprom/ffs area in 1 chip(s)...
standard eeprom/ffs offset assigned: 00E00000
flash: EC257E25082501:FFFFFF00000000
checking area [00000000]: 00000000-00FFFFFF...
Can't detect eeprom/ffs area
Do you want to use standard ffs address: 00E00000 ?
If you are not sure that standard address is correct:
1. press "NO" and terminate current operation
2. make flash backup for emergency case
3. repeat required operation
standard ffs address selected by user
detecting eeprom/ffs size...
eeprom/ffs size: 00200000
ffs chip: 00
eeprom/ffs area: 00000000:00E00000-00FFFFFF
Check firmware integrity Done
Check firmware content ...
Check firmware content Done
Backup required data ...
reading: eeprom...
file saved: C:\Program Files\InfinityBox\ChineseMiracle\eeprom_20090528-225111.B0E.bin
flash: EC257E25082501:FFFFFF00000000
Backup required data Done
Patch required data ...
Patch required data Done
Special operation ...
Special operation Done
Write ...
detect device identification#1...
detection phase #1...
.
detection phase #2...
...
warning: identification#1 information not found, possible reasons:
.old firmware type w/o identification#1 data
.damaged firmware
.damaged hardware
if phone works fine just ignore this warning
detect device identification#1 finished
detect device identification#2...
detection phase #1...
.
warning: optional information is not found,
if phone works well just ignore this warning
detect device identification#2 finished
security area (code #1) calculation...
done
detecting security area (code #2)...
security area (code #2) is absent
detect device identification#2...
detection phase #1...
.
warning: optional information is not found,
if phone works well just ignore this warning
detect device identification#2 finished
Write Fail
Finished, time used: 152 sec
Remove/Install battery now !
==== log: [28.05.2009 22:51:36] ====
COM8 [VCP0] selected
module v2.73
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection disabled
Action: write NOR flash
"smart write" active
write: Firmware
skip: Customization/Language Pack
skip: Customization
skip: Eeprom/ffs
eeprom backup enabled, it may takes several minutes !
Boot ...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing [6226:8A02:8A01]...
CPU: MT6226
high speed boot Off
chip: 0031:B1E4:6A85
high speed boot Off
boot packet size: 0002
Release Power button now !
Boot Done
Initialize ...
detecting chip #00 in region #00...
flash: EC257E25082501:FFFFFF00000000
flash: Samsung D 16Mb
detecting chip #01 in region #00...
flash: EC257E25082501:FFFFFF00000000
flash: Samsung D 16Mb
number of flash chip/regions detected: 02/01
Initialize Done
Set baud ...
921600
Set baud Done
Initialize bootcode ...
Initialize bootcode Done
Check firmware integrity ...
device parameters autodetection in progress...
detecting chip #00 in region #00...
flash: EC257E25082501:FFFFFF00000000
flash: Samsung D 16Mb
Warning: probably flash chip empty, erased, incorrectly flashed or damaged.
What to do:
1. go to software "Settings" page
2. set "Advanced chip detection method" box CHECKED !
3. make flash write operation
If still no luck: send mail to support (mt62xx@gmail.com) with detailed description of problem,
attach the next files in your e-mail:
1. C:\Program Files\InfinityBox\ChineseMiracle\operation.log
2. C:\Program Files\InfinityBox\ChineseMiracle\cfi_xxxx_xxxx.bin
detecting chip #01 in region #00...
flash: EC257E25082501:FFFFFF00000000
flash: Samsung D 16Mb
it's time to stop: FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF
number of flash chip/regions detected: 01/01
total flash region size: 01000000
detect device identification#1...
detection phase #1...
.
detection phase #2...
.................................................. .................................................. ............................
warning: identification#1 information not found, possible reasons:
.old firmware type w/o identification#1 data
.damaged firmware
.damaged hardware
if phone works fine just ignore this warning
detect device identification#1 finished
detect device identification#2...
detection phase #1...
.
warning: optional information is not found,
if phone works well just ignore this warning
detect device identification#2 finished
detecting eeprom/ffs area in 1 chip(s)...
standard eeprom/ffs offset assigned: 00E00000
flash: EC257E25082501:FFFFFF00000000
checking area [00000000]: 00000000-00FFFFFF...
eeprom/ffs found near: 00E00000
detecting eeprom/ffs size...
eeprom/ffs size: 00200000
ffs chip: 00
eeprom/ffs area: 00000000:00E00000-00FFFFFF
Check firmware integrity Done
Check firmware content ...
Check firmware content Done
Backup required data ...
reading: eeprom...
file saved: C:\Documents and Settings\Javid\Рабочий стол\eeprom_20090528-225510.B0E.bin
flash: EC257E25082501:FFFFFF00000000
Backup required data Done
Patch required data ...
Patch required data Done
Special operation ...
Special operation Done
Write ...
detect device identification#1...
detection phase #1...
.
detection phase #2...
.................................................. .................................................. ............................
warning: identification#1 information not found, possible reasons:
.old firmware type w/o identification#1 data
.damaged firmware
.damaged hardware
if phone works fine just ignore this warning
detect device identification#1 finished
detect device identification#2...
detection phase #1...
.
warning: optional information is not found,
if phone works well just ignore this warning
detect device identification#2 finished
security area (code #1) calculation...
done
detecting security area (code #2)...
security area (code #2) is absent
Area: Firmware
flash: EC257E25082501:FFFFFF00000000
Write: Firmware
detect device identification#2...
detection phase #1...
.
warning: optional information is not found,
if phone works well just ignore this warning
detect device identification#2 finished
Write Done
Finalization ...
Finalization Done
Finished, time used: 579 sec
Remove/Install battery now !
==== log: [28.05.2009 23:01:47] ====
COM8 [VCP0] selected
module v2.73
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection disabled
Action: repair security area
Boot ...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing [6226:8A02:8A01]...
CPU: MT6226
high speed boot Off
chip: 0031:B1E4:6A85
high speed boot Off
boot packet size: 0002
Release Power button now !
Boot Done
Initialize ...
detecting chip #00 in region #00...
flash: EC257E25082501:2BEA0000000000
flash: Samsung D 16Mb
detecting chip #01 in region #00...
flash: EC257E25082501:2BEA0000000000
flash: Samsung D 16Mb
number of flash chip/regions detected: 02/01
Initialize Done
Set baud ...
921600
Set baud Done
Initialize bootcode ...
Initialize bootcode Done
Check firmware integrity ...
device parameters autodetection in progress...
detecting chip #00 in region #00...
flash: EC257E25082501:2BEA0000000000
flash: Samsung D 16Mb
detecting chip #01 in region #00...
flash: EC257E25082501:2BEA0000000000
flash: Samsung D 16Mb
it's time to stop: 2B0000EA18F09FE518F09FE518F09FE518F09FE518F09FE5
number of flash chip/regions detected: 01/01
total flash region size: 01000000
detect device identification#1...
detection phase #1...
detect device identification#1 finished
identification#1 structure: 2nd [enhanced] generation
security area (code #1) is Ok
security area (code #1) backup saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_security\i d.A8A7C180.[LEDA26_06A_PCB01_GPRS_MT6226_S01.MAUI_06A_W06_48_1 2.BIN_8AD250D1].rpl
identification#1 detection finished
device-id: A8A7C180
identification#1 protocol ver: 05
ver. sw 1: LEDA26_06A_PCB01_GPRS_MT6226_S01.MAUI_06A_W06_48_1 2.BIN
ver. sw 2: MAUI.06A.W06.48.12, 2EAF2D75
ffs offset/size: 00E00000/00200000
detecting security area (code #2)...
.................................................. .................................................. ............................
security area (code #2) is absent
detect device identification#2...
detection phase #1...
.
warning: optional information is not found,
if phone works well just ignore this warning
detect device identification#2 finished
Check firmware integrity Done
Check firmware content ...
Check firmware content Done
Backup required data ...
flash: EC257E25082501:2BEA0000000000
Backup required data Done
Patch required data ...
Patch required data Done
Special operation ...
Special operation Done
Write ...
Write Done
Finalization ...
Finalization Done
file saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_security\s ystem_log_A8A7C180_LEDA26_06A_PCB01_GPRS_MT6226_S0 1.MAUI_06A_W06_48_12.BIN_8AD250D1_20090528-230415.B0X.bin
Finished, time used: 145 sec
Remove/Install battery now !
Loading file v.02...
eeprom_20090528-225510.B0E.bin loaded
==== log: [28.05.2009 23:09:44] ====
COM8 [VCP0] selected
module v2.73
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection disabled
Action: write NOR flash
"smart write" active
skip: Firmware
skip: Customization/Language Pack
skip: Customization
skip: Eeprom/ffs
error: no data to write !
Loading file v.02...
eeprom_20090528-225510.B0E.bin loaded
==== log: [28.05.2009 23:10:00] ====
COM8 [VCP0] selected
module v2.73
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection disabled
Action: write NOR flash
"smart write" active
skip: Firmware
skip: Customization/Language Pack
skip: Customization
write: Eeprom/ffs
eeprom backup enabled, it may takes several minutes !
Boot ...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing [6226:8A02:8A01]...
CPU: MT6226
high speed boot Off
chip: 0031:B1E4:6A85
high speed boot Off
boot packet size: 0002
Release Power button now !
Boot Done
Initialize ...
detecting chip #00 in region #00...
flash: EC257E25082501:2BEA0000000000
flash: Samsung D 16Mb
detecting chip #01 in region #00...
flash: EC257E25082501:2BEA0000000000
flash: Samsung D 16Mb
number of flash chip/regions detected: 02/01
Initialize Done
Set baud ...
921600
Set baud Done
Initialize bootcode ...
Initialize bootcode Done
Check firmware integrity ...
device parameters autodetection in progress...
detecting chip #00 in region #00...
flash: EC257E25082501:2BEA0000000000
flash: Samsung D 16Mb
detecting chip #01 in region #00...
flash: EC257E25082501:2BEA0000000000
flash: Samsung D 16Mb
it's time to stop: 2B0000EA18F09FE518F09FE518F09FE518F09FE518F09FE5
number of flash chip/regions detected: 01/01
total flash region size: 01000000
detect device identification#1...
detection phase #1...
detect device identification#1 finished
identification#1 structure: 2nd [enhanced] generation
security area (code #1) is Ok
security area (code #1) backup saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_security\i d.A8A7C180.[LEDA26_06A_PCB01_GPRS_MT6226_S01.MAUI_06A_W06_48_1 2.BIN_8AD250D1].rpl
identification#1 detection finished
device-id: A8A7C180
identification#1 protocol ver: 05
ver. sw 1: LEDA26_06A_PCB01_GPRS_MT6226_S01.MAUI_06A_W06_48_1 2.BIN
ver. sw 2: MAUI.06A.W06.48.12, 2EAF2D75
ffs offset/size: 00E00000/00200000
detect device identification#2...
detection phase #1...
.
warning: optional information is not found,
if phone works well just ignore this warning
detect device identification#2 finished
detecting eeprom/ffs area in 1 chip(s)...
standard eeprom/ffs offset detected: 00E00000
flash: EC257E25082501:2BEA0000000000
checking area [00000000]: 00000000-00FFFFFF...
eeprom/ffs found near: 00E00000
detecting eeprom/ffs size...
eeprom/ffs size: 00200000
ffs chip: 00
eeprom/ffs area: 00000000:00E00000-00FFFFFF
Check firmware integrity Done
Check firmware content ...
Check firmware content Done
Backup required data ...
reading: eeprom[LEDA26_06A_PCB01_GPRS_MT6226_S01.MAUI_06A_W06_48_1 2.BIN]...
file saved: C:\Program Files\InfinityBox\ChineseMiracle\eeprom[LEDA26_06A_PCB01_GPRS_MT6226_S01.MAUI_06A_W06_48_1 2.BIN]_20090528-231306.B0E.bin
flash: EC257E25082501:2BEA0000000000
Backup required data Done
Patch required data ...
Patch required data Done
Special operation ...
Special operation Done
Write ...
file saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_security\s ystem_log_A8A7C180_LEDA26_06A_PCB01_GPRS_MT6226_S0 1.MAUI_06A_W06_48_12.BIN_8AD250D1_20090528-231321.B0X.bin
Area: Eeprom/ffs
flash: EC257E25082501:2BEA0000000000
Write: Eeprom/ffs
detect device identification#2...
detection phase #1...
.
warning: optional information is not found,
if phone works well just ignore this warning
detect device identification#2 finished
Write Done
Finalization ...
Finalization Done
file saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_security\s ystem_log_A8A7C180_LEDA26_06A_PCB01_GPRS_MT6226_S0 1.MAUI_06A_W06_48_12.BIN_8AD250D1_20090528-231353.B0X.bin
Finished, time used: 231 sec
Remove/Install battery now !
WARNING ! Settings will be cleared, user data erased, Imei set to default value !
Make flash backup before this procedure !
Do you want to continue ?
==== log: [28.05.2009 23:14:22] ====
COM8 [VCP0] selected
module v2.73
Action: reset settings
Model: Autodetect 6205-6227 NOR
Checking data, wait...
Phone should be Switched OFF !
Press and HOLD Power button now !
19200 autodetect
Initializing [6226:8A02:8A01]...
CPU: MT6226
high speed boot Off
chip: 0031:B1E4:6A85
Connecting, wait...
Release Power button now !
Phone detected, wait...
Hardware: MT6226,E02
Date: 2005.04.12
Version: 1.0
Version: MAUI.06A.W06.48.12
Version: HEXING26_06A_HW
detecting structure #2...
0 done
44 byte(s) read
imei: 13579024681122
warning: current phone imei is incorrect !
It's need to repair imei for correct phone functionality !
connection Ok
building list...
done
items to clear: 150
warning: wrong packet cs
items cleared: 150 of 150
building list...
done
items remains: 0
Finished, time used: 55 sec
Remove/Install battery now !
Action: imei
Model: Autodetect 6205-6227 NOR
Checking data, wait...
Phone should be Switched ON !
Connecting, wait...
Phone detected, wait...
Hardware version: MT6226, E02
Hardware version: HEXING26_06A_HW
Software version: MAUI.06A.W06.48.12"
Software date: 2005.04.12
Barcode: MT012345678901234567
imei: 135790246811220
imei write method: mode-1
imei write channel: imei #1 for dual sim/mono CPU
new imei: 350448011234561
verification Ok
Finished, time used: 36 sec
Power off phone now !
InfinityHelp
06-01-2009, 01:41
hello!
flashfiles/ChineseMiracle/_MT6226/E553_XZY1PA_E553_GPRS_MT6226_S01.01_1__Nokia-N95_16m_En_Cn.B0M.bin
Great work. Thanks. Worked! Flashed, then repaired security area!