shama
07-01-2009, 09:33
i have a dvd china mobile i what to farmat this mobile it show like this screen shot
Device: Autodetect 6228, 6229, 6230 NAND
Checking data, wait...
Action: NAND reset
read mode: 01
Boot ...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing [6228:8A02:8A02]...
CPU: MT6228
high speed boot On
chip: 0031:9125:0101
boot packet size: 0400
Release Power button now !
Boot Done
Initialize ...
version: 3.0207
loader: 3.748.0
NAND id: ADF1801D
page size: 800+40
pages/block: 40
bits i/o: 08
address cycles: 04
blocks: 0400
ram size: 00800000
NOR: 0000:000000000000 [00000000]
NAND: 00AD:00F10080001D [08400000]
NOR chip is not installed
Initialize Done
Set baud ...
115200
Set baud Done
Identification ...
reading structure area...
detecting structure...
source data: page only
identification#1 protocol ver: 04
ver. sw 1: M320_PCB04_GPRS_MT6228_S02.M3206V10_07_12_V1_3T06D 071217.BIN
ver. sw 2: M3206V10.07.12.V1.3T06D071217, 00000000
ffs offset/size: 02000000/06000000
id-page1 Ok
nfi area detection finished: Ok
identification#1 structure: 2nd [standard] generation
Identification Done
Write ...
formatting...
...error: code: 2600006900
.................................................. ...............................................err or: code: A502000000
error: code: 0600000000
Write Fail
Finished, time used: 101 sec
Remove/Install battery now !
please solve my prablem
Device: Autodetect 6228, 6229, 6230 NAND
Checking data, wait...
Action: NAND reset
read mode: 01
Boot ...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing [6228:8A02:8A02]...
CPU: MT6228
high speed boot On
chip: 0031:9125:0101
boot packet size: 0400
Release Power button now !
Boot Done
Initialize ...
version: 3.0207
loader: 3.748.0
NAND id: ADF1801D
page size: 800+40
pages/block: 40
bits i/o: 08
address cycles: 04
blocks: 0400
ram size: 00800000
NOR: 0000:000000000000 [00000000]
NAND: 00AD:00F10080001D [08400000]
NOR chip is not installed
Initialize Done
Set baud ...
115200
Set baud Done
Identification ...
reading structure area...
detecting structure...
source data: page only
identification#1 protocol ver: 04
ver. sw 1: M320_PCB04_GPRS_MT6228_S02.M3206V10_07_12_V1_3T06D 071217.BIN
ver. sw 2: M3206V10.07.12.V1.3T06D071217, 00000000
ffs offset/size: 02000000/06000000
id-page1 Ok
nfi area detection finished: Ok
identification#1 structure: 2nd [standard] generation
Identification Done
Write ...
formatting...
...error: code: 2600006900
.................................................. ...............................................err or: code: A502000000
error: code: 0600000000
Write Fail
Finished, time used: 101 sec
Remove/Install battery now !
please solve my prablem