Flash error

[turca]

I have this is error in flash :

COM3 [VCP0] selected
module v2.84
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
Action: write NOR flash
"smart write" active
write: Firmware
skip: Customization/Language Pack
skip: Customization
skip: Eeprom/ffs
ffs/eeprom backup enabled, it may takes several minutes !
Boot ...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing [6225:8A03:8A00]...
CPU: MT6225
high speed boot On
chip: 0001:3003:0008
status: FF
boot packet size: 0400
Release Power button now !
Boot Done
Initialize ...
detecting chip #00 in region #00...
flash: EC257E25082501:968CC500000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
detecting chip #01 in region #00...
flash: EC257E25082501:968CC500000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
detecting chip #02 in region #00...
flash: EC257E25082501:968CC500000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
detecting chip #03 in region #00...
flash: EC257E25082501:968CC500000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
number of flash chip/regions detected: 04/01
Initialize Done
Set baud ...
460800
Set baud Done
Initialize bootcode ...
Initialize bootcode Done
Check firmware integrity ...
device parameters autodetection in progress...
detecting chip #00 in region #00...
flash: EC257E25082501:968CC500000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
detecting chip #01 in region #00...
flash: EC257E25082501:968CC500000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
it's time to stop: 96E2C58C1A376EDCB871E3C68D1A356A3C68D0A0C182050D
number of flash chip/regions detected: 01/01
total flash region size: 01000000
detect device identification#1...
detection phase #1...
.
detection phase #2...
.................................................. .................................................. .................................................. .................................................. .................................................. ......
warning: identification#1 information not found, possible reasons:
.old firmware type w/o identification#1 data
.damaged firmware
.damaged hardware
if phone works fine just ignore this warning
detect device identification#1 finished
detect device identification#2...
detection phase #1...
.
detect device identification#2 finished
detecting ffs/eeprom area in 1 chip(s)...
standard ffs/eeprom offset assigned: 00E00000
flash: EC257E25082501:968CC500000000
checking area [00000000]: 00000000-00FFFFFF...
ffs/eeprom found near: 00600000
Detected ffs/eeprom address is non-standard: 00600000
Posible reasons:
1. ffs/eeprom is Ok but address is non-standard
2. ffs/eeprom is damaged and can't be detected
3. ffs/eeprom is Ok but detected incorrectly (f.e. unknown ffs/eeprom structure)
If you are not sure that detected address is correct:
1. press "NO" (and select standard address or terminate current operation)
2. make full flash backup for emergency case
3. repeat required operation
Are you sure that detected ffs/eeprom address is correct ?
autodetected ffs/eeprom address confirmed by user: 00600000
detecting ffs/eeprom size...
ffs/eeprom size: 00A00000
ffs/eeprom chip: 00
ffs/eeprom area: 00000000:00600000-00FFFFFF
Check firmware integrity Done
Check firmware content ...
Check firmware content Done
Backup required data ...
reading: _ffs...
file saved: C:\Arquivos de programas\InfinityBox\ChineseMiracle\_ffs_20090706-123900.B0E.bin
flash: EC257E25082501:968CC500000000
Backup required data Done
Patch required data ...
Patch required data Done
Special operation ...
Special operation Done
Write ...
detect device identification#1...
detection phase #1...
.
detection phase #2...
.................................................. .................................................. .................................................. .................................................. .................................................. ......
warning: identification#1 information not found, possible reasons:
.old firmware type w/o identification#1 data
.damaged firmware
.damaged hardware
if phone works fine just ignore this warning
detect device identification#1 finished
detect device identification#2...
detection phase #1...
.
detect device identification#2 finished
detecting security area (code #2)...
security area (code #2) is absent
Area: Firmware
flash: EC257E25082501:968CC500000000
Write: Firmware
error: error# 00000024
error: flash write error: 00802000:00002000
error: error# 00000024
error: flash write error: 00802000:00002000
error: error# 00000024
error: flash write error: 00802000:00002000
error: error# 00000024
error: flash write error: 00802000:00002000
error: error# 00000024
error: flash write error: 00802000:00002000
error: error# 00000024
error: flash write error: 00802000:00002000
error: error# 00000024
error: flash write error: 00802000:00002000
error: error# 00000024
error: flash write error: 00802000:00002000
detect device identification#2...
detection phase #1...
.
detect device identification#2 finished
Write Fail
Finished, time used: 1056 sec
Remove/Install battery now !


Original flash file of the A968 is: E880_JJF2F12TRI_MT6225S00.GM_01_0_20080711__fullfl ash_20090702-133054.B0M cell no power help-me, infinity team

[ermizin]

Sooner whole telephone was knocked

[InfinityHelp]

I have this is error in flash :
cell no power help-me, infinity team

hello!

what cable do you use as interface?

[turca]

hello!

what cable do you use as interface?
I use pinfinder cable L10c pinout rx:5 tx:4

[InfinityHelp]

hello!

and what was phone initial problem?

[turca]

hello!

and what was phone initial problem?
Unlock i need unlock

[hadri]

use old version china miracle software thise problem its same in lg kg phone slove withe old softwere

[leomuns]

@turca

software say no Firmware in your flash chip but
it's a 1000% hardware problem change MTK

[InfinityHelp]

Unlock i need unlock

hello!

Did you modify you pinfinder box?
procedure is available in pinfinder user manual.
this will increase pinfinder output power.
probably missing power this is a reason for such behavior