Can't Remove touchscreen calibration

[..STBSL..]

I am Fulsh SpiderMan Box IEMI Cheance
I am Allrady Work By InfinityBox touchscreen Repiar


Mode : 1


COM18 [VCP1] selected
module v2.84
Action: touchscreen calibration
mode: 2
Model: Autodetect 6205-6227 NOR
Checking data, wait...
Phone should be Switched OFF !
Press and HOLD Power button now !
19200 autodetect
Initializing [6225:8A05:8A00]...
CPU: MT6225
high speed boot On
chip: 0001:E303:000D
status: FF
Connecting at 19200, wait...
Release Power button now !
Phone detected, wait...
Hardware: MT6225,E05
Date: 2006.06.14
Version: 1.0
Version: R229A_HED_V00.03_20081113
Version: PHONE25_GEMINI_HW
detecting structure #2...
5 11 done
67 byte(s) read
imei: 35044801123456
connection Ok
detecting structure #5 (mode-2)...
0warning: wrong packet cs
1warning: wrong packet cs
2 3 done
210 byte(s) read
reading data #2...
writing data...
verification...
verification Ok
Power-On and test phone now
If calibration is not completed yet:
1. make "Reverse calibration order" Checked and try again
2. try another calibration mode
Finished, time used: 11 sec
Remove/Install battery now !




Mode : 2



COM18 [VCP1] selected
module v2.84
Action: touchscreen calibration
mode: 3
Model: Autodetect 6205-6227 NOR
Checking data, wait...
Phone should be Switched OFF !
Press and HOLD Power button now !
19200 autodetect
Initializing [6225:8A05:8A00]...
CPU: MT6225
high speed boot On
chip: 0001:E303:000D
status: FF
Connecting at 19200, wait...
Release Power button now !
Phone detected, wait...
Hardware: MT6225,E05
Date: 2006.06.14
Version: 1.0
Version: R229A_HED_V00.03_20081113
Version: PHONE25_GEMINI_HW
detecting structure #2...
5 11 done
67 byte(s) read
imei: 35044801123456
connection Ok
detecting structure #5 (mode-3)...
0 1 2 3 6 done
212 byte(s) read
reading data #2...
writing data...
verification...
verification Ok
Power-On and test phone now
If calibration is not completed yet:
1. make "Reverse calibration order" Checked and try again
2. try another calibration mode
Finished, time used: 14 sec
Remove/Install battery now !

What can i do

[NawabN Sahoo]

Mate Screen caliboration have sevral mode try with all, if it is new firmware and havnt supported yet by Infinity Chinese Miricale you can upload the phone backup to Infinity support and they will support your phone in thier next update for solving urgently your problem just find a working phone with same firmware take its backup and flash to your phone.

WBR

[..STBSL..]

I am Allrady Work This InfinityUpdate_ChineseMiracle_v2.84

[kabirhossain]

you try mode-1,2,3 & check reverse calibration order. not succes? full formate & try again not success? flash your set 100% solv your problem.http://img134.imageshack.us/img134/8830/stbsl.png

br,:)
kabir telecom

[boy_muslim]

you try mode-1,2,3 & check reverse calibration order. not succes? full formate & try again not success? flash your set 100% solv your problem.http://img134.imageshack.us/img134/8830/stbsl.png

br,:)
kabir telecom
try uncheck REVERSE CALIBRATION ORDER and set to MODE-2

[..STBSL..]

you try mode-1,2,3 & check reverse calibration order. not succes? full formate & try again not success? flash your set 100% solv your problem.http://img134.imageshack.us/img134/8830/stbsl.png

br,:)
kabir telecom

Not Reselt bro ..............................

[InfinitySupport]

Hello,

If you are sure that you have used all calibration methods but still no luck - read full flash and send backup file to mt62xx@gmail.com with information about problem.
Also include operation.log file in your mail.

[cel_phon]

Try all methods one by one

i faces this problem so many times but always chinese miricle worked perfectly