View Full Version : 100% WORKING SCHEMATIC GX-10 (Max232)
i have upload the working schematic
at
http://groups.yahoo.com/group/kham/files
thanks to all members of this forum
:)
anyone tested it already ? thnkx for your work anyway man
yah any one can test
???????????????????
Siemens man
04-18-2003, 18:40
not working
sorry if it doesn't working for you
for me
all is alright !!!!!!!!!:D
You say in t he picture that donīt need external supply but you must give 5V at the picture.
I donīt understand
vcc is just the name of the signal
Thanks Kham
I tried with 1K resistor and doesnīt work for me I will try it with correct 10K resistors and post the results
The cable shematic is ok, but the pin outs are wrong.
The correct pin outs are:
pin 1 gnd
pin 1 link to 3
pin 2 link to 10
pin 5 +
pin 5 link to 12
pin 6 rx
pin 7 tx
pin 9 link to 14
Giant
are you sure @Giant
that is correct pinouts
Giant I think that your pin out it isnīt correct
schematics by kham 10000% fake
why you put ***t at forum, why you say 100% if you not tested before people like you may be banned
THIS THE 100% CORRECT SCHEMATIC TESTED BY ME 10 MINUTES BEFORE WRITING THIS POST
AT LEAST THE RIGHT SOLUTION WITH MAX232
1, 3 AND 14 TO GND
2 TO 10
6 AND 7 WITH 10k RESISITOR TO +5v
THATīS ALL
TESTED REALLY TESTED NOT LIKE OTHERS
EVERY ONE ON FORUM TRYING TO BECOME GENIOUS
SO PLEASE TEST YOUR PINOUTS FIRST AND THAN POST
OTHERWISE STILL CONFUSING WHICH 1 IS CORRECT ANSD WHICH 1 IS WRONG
Chawkiz_gsm
04-19-2003, 14:10
finally i unlock sharp good work shematic here Post #1 of 2
yes i m build > 5 circuit but not work
finally
this is the good work schematics
any cable with tx and rx and gnd but use external power
+5 v -----------resistor10k----- tx pin6
+5 v -----------resistor10k----- rx pin7
i'm use unver box inclided 3.0 gsm factory power supply
or t191 cable
use connector panasonic
connector
pin 1 gnd
pin 2 + pin 10
pin 5 + pin 11
pin 9 + pin 14
+5 v -----------resistor10k----- tx pin6
+5 v -----------resistor10k----- rx pin7
all good phone connect and sty in buckup mode
100000000% unlock after push unlock
tested by chawkiz
icq number if you need any help 178324264
__________________
unlock repair all gsm
in Tunisia + 216 98 238 031
sfax EGL
Chawkiz_gsm
04-19-2003, 14:12
kham wtih your help schematics i correct
and i m build the good schematics good kham
thx
FOR ME THIS SHEMATIC WORKS
PERHAPS THERE IS AN ANOTHER WAY TO MAKE IT WORKING
try to use an external power supply
it depends of comport technology
i have testing this cable on a laptop sony vaio
;)
thank you for your modification
@pez8210
your comport don't provide enought power
i think is better to use external vcc like you
I'm CONFUSED!!!! Wich one is working ? both working ? why not place a sticky with working scheme(s) ?
use pez8210 probe
because he is more clever than me
:D
@chawki
which panasonic cable u use for sharp
no Iīm not more clever as you but at your schematics you supply
power in pin 10 and 7 ok?
and the right pins for supply power are 6 and 7 cause are tx and rx nothing more.
with my new design you donīt need external power, you can supply vcc direct from 232 com port but in PINS 6 and 7
if you supply power in pin 10 and 7 you never unlock a sharp
Anyway thanks to kham for make me study better this schematics :)
@@pez8210
which cable you use for sharp
explain me in detail
I used and old Alcatel unlock cable with 4 wires red blue white and black read my post at sharp section
datalife2000
04-19-2003, 20:44
@ CHAWKI
" use connector panasonic"
which type of Panasonic did u use?
@ pez8210
which type of old Alcatel unlock cable did u use
dead man inc
04-19-2003, 20:58
pez8210,check your mail!!!!!!!!!
ALL THE BEST!!!!!!!
=====DEAD MAN INC=====
;) ;) ;) ;) ;)
The shematic of Kham is ok but the pin out that he use is fake, i use the pin out of my last post and it workīs 100%.
Giant
If anyone can explain to me how to put a picture here I will make schematics for posting here
@all dead man inc
Until today at 16:00 I canīt check my mail whaen I checked I will contact with you
@giant
i thing your pinouts 100%
pin 1 gnd
pin 1 link to 3
pin 2 link to 10
pin 5 +
pin 5 link to 12
pin 6 rx
pin 7 tx
pin 9 link to 14
little explanation is pin1 link 3 and pin9 link 14
will work on test mode and in test u can read /write
easily so
who will test and post results
i have no phone for TEST
Originally posted by UHK
@giant
i thing your pinouts 100%
pin 1 gnd
pin 1 link to 3
pin 2 link to 10
pin 5 +
pin 5 link to 12
pin 6 rx
pin 7 tx
pin 9 link to 14
little explanation is pin1 link 3 and pin9 link 14
will work on test mode and in test u can read /write
easily so
who will test and post results
i have no phone for TEST
Even the first pinout could put phone in test mode.
The problem is not putting phone in test mode but having comunication betwen pc and phone and none of the pinouts can do that (except maybe the one using max3316).
Pls wait , I will post the schemes for all
i have tested kham pinouts.. working 100000% for me..
datalife2000
04-25-2003, 00:51
Image now available waiting to upload. Anybody with a link to upload the gif & show here?
@ s4sajii
i'm happy for you
i think my pinout it's ok
perhaps there is a different working pinout
Originally posted by kham
[Bi think my pinout it's ok
perhaps there is a different working pinout [/B]
Yes, there is.... without vcc....
I told It :)
take an Alcatel cable for be4 with 4 wires and use red one for supply 10k resistors.
short 1, 3 and 14
short 2 and 10
Thatīs all
dead man inc
04-25-2003, 14:39
freecracker,please check your mail.And post on your web for everyone..........
Many thanks to pez8210 ;)
ALL THE BEST!!!!!
=====DEAD MAN INC=====
;) ;) ;) ;) ;)
Helo everybody,
I made the cable like "pez8210" said and works 100000000%!.........
keyboard
1------8
9------16
Thanks
TONY
Iīm very happy to see your answer ;)
Thank you very much
datalife2000
05-04-2003, 21:42
successfully unlocked two sharps gx-10 using the following schematic. tested by me 100000000%. did this after reading this forum thanx to all. :) used a Universal Box(the blackbox {i know the pinouts})
http://www.geocities.com/lungson2000/sharpdata.gif
ICQ me for any help. :) :)
Hi datalife2000
The link not working for the sharp cable schematic please send me via email also tell me the pinouts for the Universal Box because i have the Universal Box but i dont know the pinouts
Thanks
Hi
I have the original vadaphone cable and i tryit to unlock my GX-10
with the two free unlocking software, but no luck.with the unlocking.net soft i take always (something wrong try again),and with completeGSM soft always (changing to BACKUP MODE) and nothing happend.
Anyone know what going wrong?
Thanks
My cable model is:XN-1DC10
DrSPlock
05-06-2003, 00:53
Yes....power on the phone first !!!
My friend the phone was always on
inox,
Your cable is correct, and the soft is correct. It appears you probably have either a problem with your COM port, or your GX-10 is a rare old version of the phone.
Please check the soft version by typing *01763*8371# with the phone switched on. Your ohone will display, for example: a01-002-0235-gx10. If it displays ...0087-gx10, your phone has currently no way of being unlocked. We have only ever come accross 2 such handsets, in our and other offices. They appear only to be a few in the U.K..
Good luck, and let us know!
Jan Farrell
buddy the cable schematics works 100% tested by myself :-)
Burnt Cobba
05-14-2003, 02:18
tested schematics of pez8210 and works excellent
just met a version of GZ-10 A02-002-0235 dated 2003/01/27 that cant be unlocked with this software. Gets in test mode as usual and then unlocker stops.
al
0235 is a standard version, there is no reason why iy shouldn't work... strange, maybe there's a problem with your cable!
Regards,
Jan Farrell
Burnt Cobba
05-14-2003, 11:16
it stops after getting User Backup
the one i unlocked showed 0.0.7.0 and the one that cant open up shows 0.0.7.4 at the right hand corner once in User Backup screen.
al
Try removing the internal battery, waiting a minute, and replacing it again. It appears that phone has some problem! The version 0235 can be unlocked without problems!
Regards,
Jan Farrell
thnx Jjanfarell for all the support! & I rcvd the:)
Burnt Cobba
05-14-2003, 18:59
@janfarrell
thanks buddy
the thing is now free :D
br
al
wheres internal batery ? is the standard one ? got same problem, it stucks @ USER DATA BACK UP
it displays on screen @bottom right 0.0.7.4
sw version is A02-002-0235-GX10
2003/01/27 13:59:01
The Internal Bettery is inside the phone, on the PCB. You have to remove screws from the back cover and open the phone.
If a version 0235 sticks on user data backup, your problem is most probably the cable.
Regards,
Jan Farrell
i used pez8210 scheme on this box http://homepage.vianw.pt/~nx4hbg/box1.jpg
used 10k resistors, any idea ?
Have you unlocked any other phones with your cable?
You must be doing something wrong, check your power supply and schematics.
Regards,
Jan Farrell