View Full Version : How Unlock Sharp GX-13
IceKiller ZLIN
05-02-2003, 13:19
Hi all,
how unlock Sharp GX-13? Network lock?
Pinout?
Soft for unlock?
Or Calculator for imei?
Eny can me help with this phone?
Meny FNX
IceKiller
hey
vsh sells that solution @ $75 .
http://www.vsh-gsm.com/index2.htm
mp3hot
IceKiller, our soft supports GX-13 as well as GX-10 and GX-1.
Download it from our website: www.unlocKing.net
Regards,
Jan Farrell
IceKiller ZLIN
05-02-2003, 17:01
Meny fnx Janfarrell
Where i download work 100% pinout? Meny fnx. IceKiller
GSM-Unlocker
05-03-2003, 10:24
do you mean this Sharp GX-10 unlocKing Software one
Originally posted by IceKiller ZLIN
Meny fnx Janfarrell
Where i download work 100% pinout? Meny fnx. IceKiller
1+3+14=GND
7=TX
6=RX
2+10=short
B.R.
IRINeL
ALFAMOBIL TEAM
ROMANIA
www.ALFAMOBIL.ro
ICQ:153457322
IceKiller ZLIN
05-05-2003, 09:23
Is Pinout 100% work tested by you?
Meny Fnx
IceKiller
Originally posted by IceKiller ZLIN
Is Pinout 100% work tested by you?
Meny Fnx
IceKiller
This questions are very offensive. There's many big mouth ppl in the forum that deserve this questions to be made to them, but i bet my soul that Irinel is not one of them.
So if Irinel tell you that pinout then it's 100% working one for sure, and your last question to him is not only not needed but an offense.
This is my point of view only.
Have a nice day.
<RastaMan>
DrMobile
05-05-2003, 09:50
KEY PAD
-------
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
pin 1 gnd (black)
pin 2 link to 10
pin 5 + (red) ext power +3..5V
pin 5 link to 12
pin 6 rx (white)
pin 7 tx (blue) open drain, connect 10k Resistor to pin5!
pin 9 link to 14
above PINOUTS are 100% working and TESTED by many of my FRIENDS....
even this pinouts are working with MAX232
Best Regards,
Wahab
Originally posted by Trier
This questions are very offensive. There's many big mouth ppl in the forum that deserve this questions to be made to them, but i bet my soul that Irinel is not one of them.
So if Irinel tell you that pinout then it's 100% working one for sure, and your last question to him is not only not needed but an offense.
This is my point of view only.
Have a nice day.
<RastaMan>
BIG thanks for replay!!!Thank you for you affirmations, and if you need something just let me know.
B.R.
IRINeL
ALFAMOBIL TEAM
ROMANIA
www.ALFAMOBIL.ro
ICQ:153457322
No prob :D Is a pleasure try to make blind people to open his eyes :D:D
IceKiller ZLIN
05-06-2003, 13:51
I test your pinout but dont me work. i dont way?
Eny help me?
IceKiller
IceKiller ZLIN
05-06-2003, 14:25
I test all Pinout for Sharp GX-13 but dont work eny!!!
Have eny tested pinout with Sharp GX-13 and work 100% help me meny fnx.
IceKiller
Originally posted by Trier
This questions are very offensive. There's many big mouth ppl in the forum that deserve this questions to be made to them, but i bet my soul that Irinel is not one of them.
So if Irinel tell you that pinout then it's 100% working one for sure, and your last question to him is not only not needed but an offense.
Interesting. Maybe you should check the pinout that Irinel posted, it is wrong. The correct pinout was kindly posted by DrMobile. Irinel's pinout it exactly 0% working, so don't get so hyped up about "offensive" messages that someone is writing, in an attempt to not waste his time testing a bad pinout.
Regards,
Jan Farrell
Originally posted by janfarrell
Interesting. Maybe you should check the pinout that Irinel posted, it is wrong. The correct pinout was kindly posted by DrMobile. Irinel's pinout it exactly 0% working, so don't get so hyped up about "offensive" messages that someone is writing, in an attempt to not waste his time testing a bad pinout.
Regards,
Jan Farrell
Ooops! If this is true then my apologies goes to EVERYBODY that felt offended by me.
IceKiller ZLIN
05-07-2003, 17:09
Hi have you eny work schema with max 232??? I test all but dont me work.
Eny help me with me Sharp GX-13???
Fnx
IceKiller
GSM tools
05-08-2003, 12:12
2IceKiller: mail me private
I can help you
mobileclinic
05-09-2003, 09:02
Hi Ice Killer,
You can made your own cable useing this 100% working pinout originaly posted by pez8210 & tested by me.
Take a unlock cable (I did it with Mars cable with external supply or u can use other cable with 4 wire without ext. power)
Cut the connector you must have 4 wires not 3
Use panasonic G450 connector
keyboard
1------8
9------16
Red more or less +5 Vcc
Blue to Tx pin 7
White to Rx pin 6
Black to gnd connect pins 1,3,14 shorted
connect pins 2-10 shorted
in pins 7 and 6 you must put 10 k reisitor each and supply them with the red wire
Regards.
Mobileclinic
IceKiller ZLIN
05-09-2003, 13:06
To: GSM Tools
i send to you email.
TO. mobileclinic.
Testest but dont me wokr too.
IceKiller
Siemens man
05-09-2003, 20:44
@mobileclinic
not work for me
mobileclinic
05-10-2003, 07:34
Hi,
Contact me over icq-146946267,I will help you to unlock your phone.
Regards.
Mobileclinic
in the end of all this it is still not clear what the proper pinouts are .......
i have succesfull flashed gx10 with gx10 flasher and gx10i flash
and unlock with v-i-l-a-n-i soft and these pin out
phone relife thx
KEY PAD
-------
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
pin 1 gnd (black)
pin 2 link to 10
pin 5 + (red) ext power +3..5V
pin 5 link to 12
pin 6 rx (white)
pin 7 tx (blue) open drain, connect 10k Resistor to pin5!
pin 9 link to 14
100% work with a ericsson cable (max232)
thx to doctor mobile
KEY PAD
-------
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
pin 1 gnd (black)
pin 2 link to 10
pin 5 + (red) ext power +3..5V
pin 5 link to 12
pin 6 rx (white)
pin 7 tx (blue) open drain, connect 10k Resistor to pin5!
pin 9 link to 14
above PINOUTS are 100% working and TESTED by many of my FRIENDS....
even this pinouts are working with MAX232
Best Regards,
Wahab
hi i have a cable usb to phone but dont know how to unlock my sharp gx10i plz someone help
MR PROTEC
03-25-2006, 15:34
hi i have a cable usb to phone but dont know how to unlock my sharp gx10i plz someone help
download (http://www.unlock-mobile-phone.net/downloads/Sharp_GX15-GX30_unlocker.zip)
1-Connect the phone powered on and without simcard to the unlock cable.
2-Select the COM port of your unlock cable
3-mark (Gx10i)
4-click on the button APLICAR
(if you see any error ignore this errors)
In a few seconds will be unlocked
p.s: if you face any problem try in 98
wbr
KEY PAD
-------
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
pin 1 gnd (black)
pin 2 link to 10
pin 5 + (red) ext power +3..5V
pin 5 link to 12
pin 6 rx (white)
pin 7 tx (blue) open drain, connect 10k Resistor to pin5!
pin 9 link to 14
above PINOUTS are 100% working and TESTED by many of my FRIENDS....
even this pinouts are working with MAX232
Best Regards,
Wahab
Hello, I want make a serial cable with Your Pinout .
Can You explain how make a full connection to serial port RS232 ?
Thanks for all