PDA

View Full Version : SE t100 probem.

fone
07-30-2003, 21:03
Two sony-ericsson T100 .
1.phone got problem with keyborad failure ,it can press power on button Yes and No (on and off phone only).
2.other phone is that it show handfree on LCD alway.

Please advice and guide for me
thank you

it was not software repair.
marple
07-31-2003, 01:50
second T100 maybe have litle water on the conector for charging,unsolder conector,clean them and after that put him back,for first T100 try to clean keypad on the phone
pali
08-04-2003, 13:39
i have SE t100 , freezing and too slow
any idea?

b.r.

Pali
supremegsm
08-05-2003, 17:18
Try doing a software update...and even then if its slow, change the crystal.
CellM@n
08-05-2003, 18:54
if only on/off button can be used. Just pull out ur volume button, all hang problem will cure. Replace it.!!

for 2nd. have no idea yet ...

:))
platy
02-24-2004, 21:11
Hello
i have the same problem SE T100 always in Hands Free mode :mad: :mad:
phone is clean - no water.
i tryed to repair sw, remove system conector - still the same

any idea?
Thanx
Platy
fone
02-26-2004, 17:16
Hello
i have the same problem SE T100 always in Hands Free mode :mad: :mad:
phone is clean - no water.
i tryed to repair sw, remove system conector - still the same

any idea?
Thanx
Platy
handfree mode ,you remove six- pin IC where under keyboared ;it is first
cellnet
02-27-2004, 20:08
Two sony-ericsson T100 .
1.phone got problem with keyborad failure ,it can press power on button Yes and No (on and off phone only).
2.other phone is that it show handfree on LCD alway.

Please advice and guide for me
thank you

it was not software repair.


1.Rehot the CPU with many flux..tested 100%
2.remove the six pin ic
fone
02-28-2004, 20:28
1.Rehot the CPU with many flux..tested 100%
2.remove the six pin ic
1.keypad not good you must check side switch, not CPU
jojora
03-27-2004, 03:50
:confused: :(

Necesito un flash para un T106 R4D arm para flashear con terminator, o que alguien me diga donde puedo bajarme una.

Gracias de corazon.

Saludos al foro


I need a flash for a T106 R4D arm to flash with terminator, or that somebody says to me where I can lower one.

Thanks of heart.


Greetings to the forum
hooi76
04-13-2004, 06:57
i have a water damaged SE T100 keyboard phone. I clean it and the keyboard is working but the speaker and mic is not working when making a call. I can't hear from that side and that side can't hear my voice too. :(
In SERVICE TEST mode >*<<*<* i can hear mic sound from the speaker and the speaker is working too (BEEPING when pressing the keys)

Please guide
BANTUGBRO
04-25-2004, 17:01
Hi hooi76,
Try to replace the E62 three legged ic positioned at the bottom of the keypad and the problem will be solved.
WBR,
BANTUGBRO.
i have a water damaged SE T100 keyboard phone. I clean it and the keyboard is working but the speaker and mic is not working when making a call. I can't hear from that side and that side can't hear my voice too. :(
In SERVICE TEST mode >*<<*<* i can hear mic sound from the speaker and the speaker is working too (BEEPING when pressing the keys)

Please guide
hooi76
04-26-2004, 14:40
Hi, thanks for your kind reply, where can i get this E62 IC? I mean is there any compatibles from other phones to SE T100? I don't have this IC at all.
BANTUGBRO
04-26-2004, 19:32
You can get it even from siemens a35 scrap Pcb not necessarily it should be writen E62 on it but they should look similar thats important.
WBR,
BANTUGBRO.
Hi, thanks for your kind reply, where can i get this E62 IC? I mean is there any compatibles from other phones to SE T100? I don't have this IC at all.
hooi76
04-26-2004, 19:57
looks similar? do u know the code? thanks in advace
BANTUGBRO
04-29-2004, 11:36
Hey hooi76,
Check that three legged on both side IC jus besides the mic pad on the bottom of the keyboard of A35 or C35 siemens mobile PCB they are coded A7s they can be very helpful to your problm.
looks similar? do u know the code? thanks in advace
hooi76
04-29-2004, 22:02
thank you, i will try today and post the results
genocite
05-09-2004, 08:23
what's this A62 and A7s ics used for ? thanks for any good input or explanation

regards
hooi76
05-12-2004, 08:04
Thanks Mr. BANTUGBRO ,A7s is working-tested, BANTUGBRO is 100% right. but i haven't test on other codes with same size as he mention, please try and post ur results here.
hoangminhtam
05-12-2004, 15:58
i have phone with prblm. that i can not enter the menu (no thing appear when press > n no network )
only when powering on i see bat. bar n wave bar(no signal) on both side the phone does not ask for as usually "insert simcard "
i've change cpu n flash but same problm. ?
any suggested idea ?
thanx!