View Full Version : twis/ufs d500 active
pusulateknik
04-16-2005, 12:11
flash & simlock ok...
http://pinouts.ru/data/samsung_d500_pinout.shtml
USB
2 = USB D+
3 = USB +5v
4 = USB D-
8,11 = GND
For Serial Cable
5 = RX
6 = TX
8,11 = GND
18................................1
BY YOLD@S
04-16-2005, 12:34
thanks by pusula teknik
all ready poted this morning BEFORE you :) :) ha ha ha...youve all been had again :) look here http://forum.gsmhosting.com/vbb/showthread.php?t=200551
pusulateknik
04-16-2005, 12:45
all ready poted this morning BEFORE you :) :) ha ha ha...youve all been had again :) look here http://forum.gsmhosting.com/vbb/showthread.php?t=200551
my tested %100000000000000000
:D:D:D:D:D:D:D
pusulateknik
04-16-2005, 13:09
ufs/twis cable ......................
levetmar
04-16-2005, 13:18
who can reach to you? you are the best of İstanbul......
thanks man
y_info2004
04-16-2005, 16:00
great help from great boss big thanks
noman gsm
04-18-2005, 18:13
flash & simlock ok...
http://pinouts.ru/data/samsung_d500_pinout.shtml
USB
2 = USB D+
3 = USB +5v
4 = USB D-
8,11 = GND
For Serial Cable
5 = RX
6 = TX
8,11 = GND
18................................1
HAITEKGSM
04-18-2005, 20:41
thanks my friend
great
wscrsurfdude
06-20-2005, 09:10
@ Pusulateknik
The 47 resistors in the scheme are these 4.7k Ohm, 47 Ohm ??
belenm40
06-21-2005, 16:35
It worked perfectly i really appriciate the twister enabler
its 100% working or what......
i dont think its work for flash because twister not supportet flash yet
i dont think its work for flash because twister not supportet flash yet
have not tried this before . any one tried that before ?
i realise that there are D500 firmware in the Support FTP .
what cable should I use to make a D500 cable?
Is it ok to change Sericcson T28 cable to make a D500 flasher cable?
twisterfan
06-23-2005, 07:37
what cable should I use to make a D500 cable?
Is it ok to change Sericcson T28 cable to make a D500 flasher cable?
Hi
You need A300 cable..
Use the phone connector off the A300 cable and make the cable with this.
Working 1000% testet by me..
Twisterfan
hassan1975
06-25-2005, 06:11
thanx brother good job
amitks_in
06-25-2005, 06:29
Is it a combo cable USB+COm or is it com cable and Usb cable ? I think flashing time is 1 hour in com cable ! I want to know are this Schematic for cables are 2 cables 1. Com Cable 2. Usb Cable OR its A Combo Cable of USB+COM !
how can I flash D500 with a USB cable? which software should I use?
** Wait for Connect Request from Mobile...
** (POWER ON the PHONE!)
** Send '0x44' to SWIFT Chip
** Connection granted from SWIFT Chip
** Received 16 bytes from SWIFT chip
** Sending the customer ID and the same 16 bytes to SWIFT chip... OK!
** Try to change Timeout !
** Ok! Timout Changed(1600 mSecond)
** Setting downloading address (SCRAM: 0x0C000000)... OK!
** Downloading the pre-Loader (1780 bytes)...
I tried to make a D500 cable, I connect the phone and power one, and hit on Start, then powered on, and i received the message above.
plz help...
@ Pusulateknik
The 47 resistors in the scheme are these 4.7k Ohm, 47 Ohm ??
hi ...
is it 47 ... or 47k ?
hmmm ... build cable same as diagram , 47 ohm resistors
phone goes into tat mode
then
Error in Versions Info
Error in IMEI Info
Error then Reseting Phone Lock
ideas ?
eblaster101
07-25-2005, 22:17
im sure the flash features are not real the only tihng u can do is unlock
I have d500 cable and i have this error:
Error in Versions Info
Error in IMEI Info
Error then Reseting Phone Lock
SO FOR ME NOT WORK
ANOTHER SOLUTION???
I have d500 cable and i have this error:
Error in Versions Info
Error in IMEI Info
Error then Reseting Phone Lock
SO FOR ME NOT WORK
ANOTHER SOLUTION???
you need to use an earlyer version of twister_sam (q)
search this forum , you'll find it for d/l
they fixed this hack in R version of samsung
thats right use twister_sam(q) version
by the way use 4.7k resistor too
toli0000
08-30-2005, 19:08
thanks from all people of kosova
ANDID500
09-13-2005, 22:49
I HAVE THE D500 UNLOCKING DATA CABLE IT AINT EVEN GETTIN RECOGNISED BY MY PC ANY IDEAS NO NOISE OR ANYTHIN DOESNT EVEN ASK FOR A DRIVER THIS DRIVER
http://cgi.ebay.co.uk/Samsung-D500-unlocking-unlock-serial-com-data-cable_W0QQitemZ6429875109QQcategoryZ35210QQrdZ1QQc mdZViewItem#ebayphotohosting
Provaider
09-13-2005, 23:20
He a serial cabel dont need any driver only usb. You must have this cabel on the Photo no other. This work 100% without driver, i have it too
Gruß Pro
ANDID500
09-14-2005, 08:36
hi again so how do i get the samsung programs to recognise it so i can send ringtones and stuff to it its bafflin me badstyle or will i gave to buy the usb version of this tar again andi
Provaider
09-14-2005, 13:08
You have buy a Flash and unlock Cabel not a Datacabel, Buy a USBcabel or BT
Pro
Gsmsassa
10-09-2005, 21:14
hi
thanks good solution
MaximusDK
10-25-2005, 09:31
is it a 1N4148 or a 1N414B diode to use in the cable?
Regards MaximusDK
it is a IN4148, eight not bee