FOR TEST PURPOSE I HAVE TRIED A RUNNING CDMA SET C2201 TO DETECT RX TX
ITS PIN OUT IS
1.........24
11: Gnd
12: Tx (RJ-45 pin-3)
13: Rx (RJ-45 pin-2)
15: +charge

BUT PINFINDER CANT DETECT IT AND THE SET IS DEAD NOW...
I CANT UNDERSTAND HOW THE SET BECOME DEAD WITH PINFINDER EVEN IT CAN'T DETECT IT'S PINOUT ...:confused:

FOR TEST PURPOSE I HAVE TRIED A RUNNING CDMA SET C2201 TO DETECT RX TX
ITS PIN OUT IS
1.........24
11: Gnd
12: Tx (RJ-45 pin-3)
13: Rx (RJ-45 pin-2)
15: +charge

BUT PINFINDER CANT DETECT IT AND THE SET IS DEAD NOW...
I CANT UNDERSTAND HOW THE SET BECOME DEAD WITH PINFINDER EVEN IT CAN'T DETECT IT'S PINOUT ...:confused:
Be sure that phone is not in sleep mode during pinout detection !
Press any phone key from time to time to wake-up phone.
detecting pins.... GOOD LUCK TRY AGAN.

It's not possible to damage phone during PinFinder usage.
If your phone was able to Power-On from PinFinder during pinout detection process but can't power-on from battery you must charge battery.

It's not possible to damage phone during PinFinder usage.
If your phone was able to Power-On from PinFinder during pinout detection process but can't power-on from battery you must charge battery.

its happened sir
its my own set not recieved from customer, and it was 100% working before test
and now it cant detect even with huawei tool with its cable !!!

It's not possible to damage phone during PinFinder usage.

If phone was unable to power-on during pinout detection this means that you have connected "+" and "-" wires to phone incorrectly.

its happened sir
its my own set not recieved from customer, and it was 100% working before test
and now it cant detect even with huawei tool with its cable !!!



pinfinder use only for pin detaction pin finder not tuch any ohter hardwars of phone so u can duble cechk your phone battery power button etc.......

Br.

excuse me to all
i m sorry to say that i have minimum experience to understand battery charge and the +ve/-ve connector
and that set i was using till test
i m not blaming pinfinder, ofcourse it is best device for pin detection but i want to know why it cant detect and how it make it dead
pls dont reply again with charge or connector .....

excuse me to all
i m sorry to say that i have minimum experience to understand battery charge and the +ve/-ve connector
and that set i was using till test
i m not blaming pinfinder, ofcourse it is best device for pin detection but i want to know why it cant detect and how it make it dead
pls dont reply again with charge or connector .....

You must connect PinFinder power wires according to manual.
You must connect + to + and - to -.
If you connect power cable incorrectly (+ to -) you can damage your phone by wrong voltage.
So you must be very careful.

See PinFinder manual page 12 for more information.

sorry again,
another huawei 2201 totally short by pinfinder , its also for test and it was running set too
so where is the problem with this , pls check on huawei 2201 and 2205
i have told before about batt connector ... and for this time i m 100% sure that i m right for the second test
so is it better to not to use pinfinder with those cdma sets ???

sorry again,
another huawei 2201 totally short by pinfinder , its also for test and it was running set too
so where is the problem with this , pls check on huawei 2201 and 2205
i have told before about batt connector ... and for this time i m 100% sure that i m right for the second test
so is it better to not to use pinfinder with those cdma sets ???

check with multimetre if your cable ouput vpp is good

is the read CABLE is + ? ...

cable out put is ok
i m working fine with my pinfinder , but for that set it become short after test

tested with huawei c2601 no problem. phone is still alive.

strange problem with dead set, never happen with that.

ok fine pls test with huawei 2201 or 2205 and give the result
may be problem is only for me !!!

Hello,

I don't think that your phone can be dead due to PinFinder due to PinFinder output voltage can not be more that 5v in any case (PinFinder take power from PC USB port).
Please, somebody post here more reports with CDMA sets (in fact I never heard before about any damaged CDMA or GSM phones after PinFinder usage).

i am having sigmatel s3 set dead after flashing with infinity why

@sharpgsm
because you have used flash file that is not suitable for your phone.
You must get more information here: http://www.gsmhosting.com/vbb/forumdisplay.php?f=425

I lost my battery cable anybaody has the pinout or the way that I can make it thank you in advance

I lost my battery cable anybaody has the pinout or the way that I can make it thank you in advance

C:\Program Files\InfinityBox\Documentation\PinFinder\Infinity-Box_PinFinder.pdf

See page 34.

Output #2, RJ45, 8 pins
1 Vpp, power
7 Gnd
8 Gnd