Samsung SM-G610S Reset FRP question [Solved] - GSM-Forum

mobileman2013 · 07-20-2018, 11:52

Welcome to Octoplus FRP Tool v.1.3.4.0
Platform: SAMSUNG
Selected model: SM-G610S
Searching for UART interface.. COM12
Connect Samsung Micro UART cable(with 525K resistor), press and hold "Vol-" + "Power" buttons for 15-20 seconds
Searching for device. Please wait...
Operation was canceled
Performed by 1.3.4.0 Software version.

Platform: SAMSUNG
Selected model: SM-G610S
Searching for UART interface.. COM12
Connect Samsung Micro UART cable(with 525K resistor), press and hold "Vol-" + "Power" buttons for 15-20 seconds
Searching for device. Please wait...
Phone found.
Rebooting phone in Upload Mode...OK
Please connect phone to USB cable..
Searching for a phone. Please wait...OK
Reading data...
Checking operation...
This version of "sBoot" is not supported, try to downgrade "sBoot"!
Operation was failed!
Performed by 1.3.4.0 Software version.

Octopus box · 07-20-2018, 14:21

Hello.

Please read attentively Software log and update news:

Quote:

This version of "sBoot" is not supported, try to downgrade "sBoot"!

Quote:

* Note: this operation works for the mentioned above devices with Android 6.x firmwares' versions and may not work for some phones’ S-boot. In this case try to write another firmware version or only S-boot from firmware and repeat the operation again.

For Android 7.x firmwares You cant try to do the following:
1. Write only Sboot (not full firmware) from Android 6.x firmware.
2. Perform "Reset FRP" operation.
3. Write Sboot from Android 7.x firmware.

mobileman2013 · 07-21-2018, 06:10

problem solve thnk you so much octopus team

Welcome to Octoplus Box Samsung software version 2.6.9
-----------------------------------------------------------------------------------
To connect SM-J700F phone you have to perform the following steps:
1. Disconnect USB cable from phone.
2. Go to Menu->Settings->More->About Device.
3.Tap on "Build number" 7 times to enable developer options.
4. Go to Menu->Settings->More->Developer options.
5. Turn on "USB Debugging" option.
-----------------------------------------------------------------------------------
Platform: Samsung Android
Selected port: COM1
Selected model: SM-G610S
Operation: Reset FRP - UART EMMC
Searching for UART interface..
Found more then one box connected to COM12 COM12
Connect Samsung Micro UART cable(with 525K resistor), press and
hold "Vol-" + "Power" buttons for 15-20 seconds
Searching for device. Please wait...
Operation was canceled
Performed by 2.6.9 Software version.
-----------------------------------------------------------------------------------
Platform: Samsung Android
Selected port: COM12
Selected model: SM-G610S
Operation: Reset FRP - UART EMMC
Searching for UART interface..
Found more then one box connected to COM12 COM12
Connect Samsung Micro UART cable(with 525K resistor), press and
hold "Vol-" + "Power" buttons for 15-20 seconds
Searching for device. Please wait...
Phone found.
Rebooting phone in Upload Mode...OK
Please connect phone to USB cable..
Searching for a phone. Please wait...OK
Reading data...
Checking operation...OK
Searching for UART interface..
Found more then one box connected to COM12 COM12
Connect Samsung Micro UART cable(with 525K resistor), press and
hold "Vol-" + "Power" buttons for 15-20 seconds
Searching for device. Please wait...
Phone found.
Resetting FRP lock (1/4 attempt)..success
FRP / Reactivation lock is successfully reseted!
Performed by 2.6.9 Software version.

07-20-2018, 11:52	#1 (permalink)
mobileman2013 Registered User Join Date: Feb 2016 Posts: 115 Member: 2530239 Status: Offline Thanks Meter: 14	Samsung SM-G610S Reset FRP question [Solved] Welcome to Octoplus FRP Tool v.1.3.4.0 Platform: SAMSUNG Selected model: SM-G610S Searching for UART interface.. COM12 Connect Samsung Micro UART cable(with 525K resistor), press and hold "Vol-" + "Power" buttons for 15-20 seconds Searching for device. Please wait... Operation was canceled Performed by 1.3.4.0 Software version. Platform: SAMSUNG Selected model: SM-G610S Searching for UART interface.. COM12 Connect Samsung Micro UART cable(with 525K resistor), press and hold "Vol-" + "Power" buttons for 15-20 seconds Searching for device. Please wait... Phone found. Rebooting phone in Upload Mode...OK Please connect phone to USB cable.. Searching for a phone. Please wait...OK Reading data... Checking operation... This version of "sBoot" is not supported, try to downgrade "sBoot"! Operation was failed! Performed by 1.3.4.0 Software version. Last edited by Octopus box; 07-21-2018 at 08:41.

07-21-2018, 06:10	#3 (permalink)
mobileman2013 Registered User Join Date: Feb 2016 Posts: 115 Member: 2530239 Status: Offline Thanks Meter: 14	Samsung SM-G610S Reset FRP successfully done problem solve thnk you so much octopus team Welcome to Octoplus Box Samsung software version 2.6.9 ----------------------------------------------------------------------------------- To connect SM-J700F phone you have to perform the following steps: 1. Disconnect USB cable from phone. 2. Go to Menu->Settings->More->About Device. 3.Tap on "Build number" 7 times to enable developer options. 4. Go to Menu->Settings->More->Developer options. 5. Turn on "USB Debugging" option. ----------------------------------------------------------------------------------- Platform: Samsung Android Selected port: COM1 Selected model: SM-G610S Operation: Reset FRP - UART EMMC Searching for UART interface.. Found more then one box connected to COM12 COM12 Connect Samsung Micro UART cable(with 525K resistor), press and hold "Vol-" + "Power" buttons for 15-20 seconds Searching for device. Please wait... Operation was canceled Performed by 2.6.9 Software version. ----------------------------------------------------------------------------------- Platform: Samsung Android Selected port: COM12 Selected model: SM-G610S Operation: Reset FRP - UART EMMC Searching for UART interface.. Found more then one box connected to COM12 COM12 Connect Samsung Micro UART cable(with 525K resistor), press and hold "Vol-" + "Power" buttons for 15-20 seconds Searching for device. Please wait... Phone found. Rebooting phone in Upload Mode...OK Please connect phone to USB cable.. Searching for a phone. Please wait...OK Reading data... Checking operation...OK Searching for UART interface.. Found more then one box connected to COM12 COM12 Connect Samsung Micro UART cable(with 525K resistor), press and hold "Vol-" + "Power" buttons for 15-20 seconds Searching for device. Please wait... Phone found. Resetting FRP lock (1/4 attempt)..success FRP / Reactivation lock is successfully reseted! Performed by 2.6.9 Software version. Last edited by Octopus box; 07-21-2018 at 08:41.