3210 Flash Id 00000000!!! - GSM-Forum

GSMtricks2002 · 03-27-2002, 21:26

I`l try to falsh 3210 but nithing Flash ID 000000

remle · 03-27-2002, 22:54

You got defective flash. Replacement of flash is the only solution i know.

GSMtricks2002 · 03-27-2002, 23:51

Before flashing was all o`key!!!

Bogi · 03-28-2002, 04:53

Try different flash loaders with Dejan 1.0b.You will flash your phone.I`ve got a 3310 with flash ID 00888990 - correct is 00898890,but phone is O.K.

j_h_u_n · 03-28-2002, 13:29

Dont worry,just flash it again and again with rolis4.77/Dejan 1.00b until it will work.Then calculate faid.I already also experience it.The phone hang-up while erasing the flash.

Take care
j_h_u_n

GSMtricks2002 · 03-28-2002, 14:19

i was try with rolis4.77 but it write: UNKNOWN FLASH TYPE!!!
With Dejan: erasing flash error!!!

Bogi · 03-28-2002, 14:23

Open phone and tell me what type is your flash ic - Atmel or Intel.Don`t worry - in both cases your phone will be O.K.

GSMtricks2002 · 03-28-2002, 14:42

Atmel 850
24c128n

j_h_u_n · 03-28-2002, 20:11

Nop,the 24c128 is an eeprom not a flash chip.As long as the hardware is good, it should work.

j_h_u_n

crusher · 03-31-2002, 00:09

get a winhex, or something else, cut your flash into 0.5MByte parts, then flash each part individually to the corresponding start address. This will solve all flash erasing problems, if not, your flash is physically bad, or conduction is damaged between PCB and flash chip. Also remember to do it with well-charged battery.

BR
crusher

PS. easter egg will come to all of ya

aZyWeRks · 03-31-2002, 00:42

its a hardware problem. your flash ic has loose solder contacts underneath.

try reflowing flash ic. just be careful though.

regards,

aCe

03-27-2002, 21:26	#1 (permalink)
GSMtricks2002 Junior Member Join Date: Mar 2002 Age: 44 Posts: 15 Member: 10331 Status: Offline Thanks Meter: 0	3210 Flash Id 00000000!!! I`l try to falsh 3210 but nithing Flash ID 000000

03-27-2002, 23:51	#3 (permalink)
GSMtricks2002 Junior Member Join Date: Mar 2002 Age: 44 Posts: 15 Member: 10331 Status: Offline Thanks Meter: 0	Before flashing Before flashing was all o`key!!!

03-28-2002, 14:19	#6 (permalink)
GSMtricks2002 Junior Member Join Date: Mar 2002 Age: 44 Posts: 15 Member: 10331 Status: Offline Thanks Meter: 0	NOTHING i was try with rolis4.77 but it write: UNKNOWN FLASH TYPE!!! With Dejan: erasing flash error!!!

03-28-2002, 14:23	#7 (permalink)
Bogi No Life Poster Join Date: Jul 2001 Location: Bulgaria Age: 53 Posts: 957 Member: 5579 Status: Offline Thanks Meter: 5	Open phone and tell me what type is your flash ic - Atmel or Intel.Don`t worry - in both cases your phone will be O.K. Last edited by Bogi; 03-28-2002 at 14:30.

03-28-2002, 14:42	#8 (permalink)
GSMtricks2002 Junior Member Join Date: Mar 2002 Age: 44 Posts: 15 Member: 10331 Status: Offline Thanks Meter: 0	Flash Atmel 850 24c128n

03-27-2002, 22:54	#2 (permalink)
remle Freak Poster Join Date: Nov 1999 Posts: 99 Member: 683 Status: Offline Thanks Meter: 0	You got defective flash. Replacement of flash is the only solution i know.

03-28-2002, 04:53	#4 (permalink)
Bogi No Life Poster Join Date: Jul 2001 Location: Bulgaria Age: 53 Posts: 957 Member: 5579 Status: Offline Thanks Meter: 5	Try different flash loaders with Dejan 1.0b.You will flash your phone.I`ve got a 3310 with flash ID 00888990 - correct is 00898890,but phone is O.K.

03-28-2002, 13:29	#5 (permalink)
j_h_u_n Major Poster Join Date: Mar 2002 Location: from nowhere Age: 50 Posts: 42 Member: 10239 Status: Offline Thanks Meter: 0	Dont worry,just flash it again and again with rolis4.77/Dejan 1.00b until it will work.Then calculate faid.I already also experience it.The phone hang-up while erasing the flash. Take care j_h_u_n

03-28-2002, 20:11	#9 (permalink)
j_h_u_n Major Poster Join Date: Mar 2002 Location: from nowhere Age: 50 Posts: 42 Member: 10239 Status: Offline Thanks Meter: 0	Nop,the 24c128 is an eeprom not a flash chip.As long as the hardware is good, it should work. j_h_u_n

03-31-2002, 00:09	#10 (permalink)
crusher No Life Poster Join Date: Dec 2001 Location: [winscard.SCardTransmit] Posts: 1,835 Member: 8023 Status: Offline Thanks Meter: 13	get a winhex, or something else, cut your flash into 0.5MByte parts, then flash each part individually to the corresponding start address. This will solve all flash erasing problems, if not, your flash is physically bad, or conduction is damaged between PCB and flash chip. Also remember to do it with well-charged battery. BR crusher PS. easter egg will come to all of ya

03-31-2002, 00:42	#11 (permalink)
aZyWeRks Freak Poster Join Date: Jan 2001 Location: I.C., R.P. Posts: 185 Member: 3165 Status: Offline Thanks Meter: 0	its a hardware problem. your flash ic has loose solder contacts underneath. try reflowing flash ic. just be careful though. regards, aCe

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
3310 Unknown flash type.flash ID.00000000	Mia Cellcom	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	6	03-03-2005 10:22
flash ID 00000000	TEKIN	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	3	02-25-2003 14:17
3310 don't flashing,ID 00000000 HELP!!	chopper	Nokia Hardware & Hardware Repair	2	01-25-2003 09:43
3310 flash ID 00000000	MadPhone	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	3	05-22-2002 05:07
Flash 3210 flash ID 898890	celo	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	1	12-26-2001 11:46