Bph&Co,X-Shadow pleas read

[Format1]

Hi !

At first I`m appologize for writing topic that<br />we tallking many times beafore.<br />I find many dieference answer to my question and now I`m apsolutly<br />confused.So I decide to ask You to answer me.<br />What should I use for reading and what for writing in flasher.cfg for<br />Nokia 3330 phone.?And from where is real address of mcu,ppm and eeprom?<br />Somebody say that best is 65 08,somebody 65 06 and etc...<br />I hope that You understand what and whay I post same topic again.<br />I need right answer and I`m hope that You will give it to me.

Thanks

Format

[G-Man]

65 08 read reading and writting of 3330!<br />PPM always starts at 49K but eeprom is sometimes at 5EK or 55K

[mudboy]

But i heard:<br />3330 reading 65 08<br />writing 65 05 (like 3310)

So???

Regards Mudboy

[Lead]

Use 65 08 for both reading and writing.<br />65 05 works for writing also, but may cause some problems.

[MAK_US1977]

Dear Friends<br />anybody know what is happend to Bph&Co and Daniel<br />I send them emails and no replay

I think he was the manger for <a href="http://phreaks.co.uk/" target="_blank">http://phreaks.co.uk/</a>

Thanks

[Format1]

Hi !

Thanks to all for offering help.But again there is answer like I heard 65 05 for writing,65 08 for reading and writing.... <img src="confused.gif" border="0"> <br />I look at Dark shell v 2.11.In flasher.cfg file for 3330 is 65 05 , but in 3330.cfg file is 65 08 <img src="confused.gif" border="0"> <img src="confused.gif" border="0"> <br />What is going on? Pleas somebody be gently and explane.

G-Man could you fix or confirm this start addresses:<br />3330<br />MCU = 00200000 - 0048FFF0<br />PPM = 00490000 - ????????<br />Eeprom = ???????? - 00600000

Thanks

I hope that we finaly solve this problem about *.cfg file for 3330.

Regards

[G-Man]

Here is requested info:<br />3330 (NHM-6) 3.05, 4.12, 4.16<br />Best config setting = 3330 65 08<br />Full flash = 00200000 - 00600000<br />MCU = 00200000 - 00490000<br />PPM = 00490000 - 00550000<br />Eeprom = 00550000 - 00600000

3330 (NHM-6) 3.12<br />Best config setting = 3330 65 08<br />Full flash = 00200000 - 00600000<br />MCU = 00200000 - 00490000<br />PPM = 00490000 - 005E0000<br />Eeprom = 005E0000 - 00600000

3330 (NHM-6) 4.30<br />Best config setting = 3330 65 08<br />Full flash = 00200000 - 00600000<br />MCU = 00200000 - 00490000<br />PPM = 00490000 - 005F0000<br />Eeprom = 005F0000 - 00600000

I don't know for 3.10 because I don't have full flash (20k - 60k) I only have firmware backup.

[Format1]

Sir G-Man *** bless You <img src="smile.gif" border="0"> <br />Thank You very much.Finaly I know.

<br />I will take this chance to ask You one more thing thatis very important for me.<br />I don`t know how could I with hex editor cut PPM,MCU and eeprom part from full flash.<br />Lets supose that I have full flash from 3310 phone.It is from 00200000 to 00400000.Than I use hex editor and I whant to cut MCU (or PPM or Eprom) area only.How to do it.?<br />If You have litle time to explane I will be happynest man in the world.

Thank you again.

Regards

Format

[G-Man]

Open full flash in hex editor.<br />Say you don't know address that PPM starts just search for text string PPM after about 3 finds it will find the start of the PPM area it will look like:<br />PPM.V 04.94.27-09-00.NSE-5.(c) NMP......B<br />Example is from a 7110 sw v4.94 with PPM B.<br />Just highlight the area you want and copy it into a new file.

Or if you know the address just go to start of PPM hold shift and go to start of eeprom.

[ 08 November 2001: Message edited by: G-Man ]</p>

[Format1]

Hi G-Man !

Thanks.

Now I understand how to "pull out" MCU.Open full flash.Mark from start to PPM.V 04.94.27-09-00.NSE-5.(c) NMP......B (but without PPM.V 0494... because there start PPM) save it and you will get MCU from full flash.OK?<br />But if I whant PPM without MCU.? I open full flash.Mark area from "PPM.V 04.94.27-09-00.NSE-5.(c) NMP......B" to ??????? where ?<br />I don`t know where is the end of the PPM and where is start of the Eeprom area when I open full flash with hexeditor.<br />I hope that you understand what I`m trying to say.

Thanks<br />Format

[greenapple]

try this.

in hex editor. open a full flash file. search for PPMV.<br />if you found it. good.

if front of PPMV. you will see 50 50 4d 00 PPMV. ignore this. what is important is the 4 bytes in front of it. ex. 0x00289330. subract 0x200000 from it and u will get 0x89330.

go to this location and you will get another 8 bytes. it's the start and end. subtract 0x200000 to both of them, and it's the starting address of PPM and 2nd 4 bytes is the ending address.

hope you understand it... <br /> <img src="smile.gif" border="0">