I unlocked all new 3210/5110 with this method

[igor_m]

for 5.31 and 5.28(csi also)
1.press readme
2.connect 5&6 wires
3.press open all
and in progress count 2 sec from the
moment its start open
all locks open.
only 15sec time need.

for 5.36 connect 5&6 and do ussual trick.
its working and tested by me.

maybe smb can help me with emmi-sp
i'm looking for it plss.

[Stef]

With what profram?

[Stef]

Sorry,with what program?

[brittnee]

not quite complete info,
after press open all , wait 2 seconds then remove the pin? is that right or after i see open then i remove the connection after 2 seconds?

Originally posted by igor_m:
for 5.31 and 5.28(csi also)
1.press readme
2.connect 5&6 wires
3.press open all
and in progress count 2 sec from the
moment its start open
all locks open.
only 15sec time need.

for 5.36 connect 5&6 and do ussual trick.
its working and tested by me.

maybe smb can help me with emmi-sp
i'm looking for it plss.

[igor_m]

sorry , i read my post now ,i coludnt
understand ,i try explain again .
SO luck ,everytime you short pin on
eeprom ,information in eeprom changed,
and so checksum changed .
I read many topics in forum cant
unlock .

Again .
1.press readme phone
2.short 5&6 wires press unlock ,and in
the middle of progress dissconect
wires ,but be sure that u solder wires
good.
3.all locks open.

----some time when u make 6&7 trick
then u can unlock phone wit 5&6 ,
so u need to connect 3 of pin
5&6&7
5&7&8.
and some times press 5 or 10 times
on closed (i think u know it).
I never have contact service on phone
only 5.29 when u solder wires connect it
and switch on phone ,u can see contact
service ,but disconnect it and all ok.
Plss make everything carefully ,even
u can crash your phone with hihg temperature
of solder-gun .Also be carefull with
3210 ,near 5 & 6 leg u can see small part,
dont destroy it.
Software I need :
Nokia unlocker by Dr KZ (i think u have it)
Nokia tool 29 pro
Nokia tool 34 pro
I tried to make with 033 ,dont work propely.
So regards if any quastion ,ask .

[GSD]

I not understand why people have problem with 5.28, 5.29 & 5.31, 5.36. I unlock over 300 peaces with pin 5 method and never have problem or “contact service”. This method works for me with atmel, csi and one new eprom which name I forget.

1. Open phone.
2. Very careful solder wire (isolated) to pin 5 and bring you out.
3. Assemble phone without front (5110) or back (3210) cover.
4. Power phone on.
5. Connect phone to M-bus.
6. Run Nokia tool by Pro 033 (work fine).
7. Press “Read ME” (everything is normal).
8. Take non-isolated part of wire in your finger.
9. Press “Read-ME” (you see funny IMEI).
If IMEI not funny maybe your skin is to dry (little water is very useful)
10. 5 times press “Unlock”.
11. Let you wire out from your finger.
12. Finally press “Unlock” and phone is unlocked.

If phone stay closed repeat all from step 7 (work 100%).

P.S.
***** foot and wire in your ***** is not necessary.

[GSD]

Sorry, in step 10 and 12 press "Closed"

[igor_m]

tool pro 033 dont work fine with new phones

[Stryker]

hi!

i use 6-7 trick (5.28, 5.31) or pin5 grounding (5.28,5.29,5.31,5.36) and never have 'contact service'. its how you handle your fone/procedure.

have a nice day!!

[Sammie Belamide]

Hi all

Which layout it correct, is it

*-5---6---7--8-*
* *
* 24c16 *
* *
* * *
*-1---2---3--4-*

or this one

*-8---7---6--5-*
* *
* 24c16 *
* *
* * *
*-1---2---3--4-*

* represent the hard dot in the IC

Dagger illustrate the 1st one and you otherwise, can you help on this, i've used the second illustration in unlocking Nokia 3210 v05.36 using dagger method and got "Contact service" and my day gone bad . Can you help me on this. Is there other method in unlocking 5.36 Nokia 3210.

Thanks in advance

Sammie Belamide
sbelamide@edsamail.com.ph

Originally posted by GSD:
I not understand why people have problem with 5.28, 5.29 & 5.31, 5.36. I unlock over 300 peaces with pin 5 method and never have problem or “contact service”. This method works for me with atmel, csi and one new eprom which name I forget.

1. Open phone.
2. Very careful solder wire (isolated) to pin 5 and bring you out.
3. Assemble phone without front (5110) or back (3210) cover.
4. Power phone on.
5. Connect phone to M-bus.
6. Run Nokia tool by Pro 033 (work fine).
7. Press “Read ME” (everything is normal).
8. Take non-isolated part of wire in your finger.
9. Press “Read-ME” (you see funny IMEI).
If IMEI not funny maybe your skin is to dry (little water is very useful)
10. 5 times press “Unlock”.
11. Let you wire out from your finger.
12. Finally press “Unlock” and phone is unlocked.

If phone stay closed repeat all from step 7 (work 100%).

P.S.
***** foot and wire in your ***** is not necessary.

[Mediamag]

I don´t understand this discution, all unlockers hav no problem vith Nokia and the other people are no unlockers. They are customers and try to unlock the phone. It is not good idea to play with the phone. Or you know what to do or you can play with small plastic car.

[Stryker]

hey man, you're right! hehehe!

[brittnee]

layout 2 is correct, and dagger method is guaranteed working!!!!

Originally posted by Sammie Belamide:
Hi all

Which layout it correct, is it

*-5---6---7--8-*
* *
* 24c16 *
* *
* * *
*-1---2---3--4-*

or this one

*-8---7---6--5-*
* *
* 24c16 *
* *
* * *
*-1---2---3--4-*

* represent the hard dot in the IC

Dagger illustrate the 1st one and you otherwise, can you help on this, i've used the second illustration in unlocking Nokia 3210 v05.36 using dagger method and got "Contact service" and my day gone bad . Can you help me on this. Is there other method in unlocking 5.36 Nokia 3210.

Thanks in advance

Sammie Belamide
sbelamide@edsamail.com.ph

Hi,
Tried who to unlock 3210 5.36 with programm "NOKIA TOOL 3210.5.36 SIMLOCKMAN"?
As this programm work?
Josif&R

[Rossend]

This is NokiaTool with changed Title bar. :-)