question for x-shadow..b - GSM-Forum

timitiz · 11-10-2000, 00:08

Hi X-Shadow..

In other topic about 3210 v6.0 you say : make back up from 3210 before unlocking...
But, how do you make backup from eprom ?, which program do you use ? , can you reprogramm eprom while in phone ?

thanks & greetingz Timitiz

Robby · 11-10-2000, 07:03

Hello he means by eeprom reader you must open the phone , plug soic on IC and read it.
Regards Robby

timitiz · 11-11-2000, 00:22

Hi Robby...

Normaly i would reply to you private, but i think many of us would like to know how to read eprom, what tools , what prog..

I tried to read eprom with jdm programmer, which i often use to repair lasergames outfits, but this was not a succes...
if you know how tu use it, let us also know..

Greetingz Timitiz..

Robby · 11-11-2000, 01:03

Hello Timitiz
I use Pony programer to read write eeproms.
look on the schematics how is conected
[img] http://www.ixitiki.com/1.jpg [/img]
[img] http://www.ixitiki.com/2.jpg [/img]
On 3210 eeprom I am reading direct from PCB with out problem.
Regards Robby

Robby · 11-11-2000, 01:05

Hello Timitiz
I use Pony programer to read write eeproms.
look on the schematics how is conected

On 3210 eeprom I am reading direct from PCB with out problem.
Regards Robby

timitiz · 11-11-2000, 14:41

Thanks Robby for your answer...

But only one thing now... is it also possible to reprogram eprom with pony prog?

Greetingz & Thanks again...

Timitiz..

Robby · 11-11-2000, 14:44

Yes very easy.
Everytime you flash eeprom you reprogramme it, from the begining.
You can also erase it, and have it blank.
Regards
Robby

timitiz · 11-11-2000, 14:48

Thanks Robby..

I'll try it tonight, and will let you know the results...

Greetingz Timitiz..

mobileman · 11-15-2000, 00:59

robby, please send me pony programmer, and basic info/guidlines...thanks..

11-10-2000, 00:08	#1 (permalink)
timitiz Freak Poster Join Date: Jul 2000 Location: Zaandam, the netherlands Posts: 263 Member: 1715 Status: Offline Thanks Meter: 0	question for x-shadow..b Hi X-Shadow.. In other topic about 3210 v6.0 you say : make back up from 3210 before unlocking... But, how do you make backup from eprom ?, which program do you use ? , can you reprogramm eprom while in phone ? thanks & greetingz Timitiz

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
questions for ub support, and for all	alexvideogames	Universalbox	0	09-14-2007 19:02
Question to X-Shadow	Tygiel	Nokia Digital Core Technology 4 ( DCT-4 )	0	02-13-2003 19:30
question for melodies for S35	alekso	x1x to x45/x50	1	07-31-2002 13:40
POST FOR X-SHADOW	johntrk	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	0	07-24-2001 23:41
For X-shadow	PADERF	Various	2	11-09-2000 00:14

11-10-2000, 07:03	#2 (permalink)
Robby VIP-Member Join Date: Jun 1999 Location: Athens, Greece Posts: 214 Member: 254 Status: Offline Thanks Meter: 7	Hello he means by eeprom reader you must open the phone , plug soic on IC and read it. Regards Robby

11-11-2000, 00:22	#3 (permalink)
timitiz Freak Poster Join Date: Jul 2000 Location: Zaandam, the netherlands Posts: 263 Member: 1715 Status: Offline Thanks Meter: 0	Hi Robby... Normaly i would reply to you private, but i think many of us would like to know how to read eprom, what tools , what prog.. I tried to read eprom with jdm programmer, which i often use to repair lasergames outfits, but this was not a succes... if you know how tu use it, let us also know.. Greetingz Timitiz..

11-11-2000, 01:03	#4 (permalink)
Robby VIP-Member Join Date: Jun 1999 Location: Athens, Greece Posts: 214 Member: 254 Status: Offline Thanks Meter: 7	Hello Timitiz I use Pony programer to read write eeproms. look on the schematics how is conected [img] http://www.ixitiki.com/1.jpg [/img] [img] http://www.ixitiki.com/2.jpg [/img] On 3210 eeprom I am reading direct from PCB with out problem. Regards Robby

11-11-2000, 01:05	#5 (permalink)
Robby VIP-Member Join Date: Jun 1999 Location: Athens, Greece Posts: 214 Member: 254 Status: Offline Thanks Meter: 7	Hello Timitiz I use Pony programer to read write eeproms. look on the schematics how is conected On 3210 eeprom I am reading direct from PCB with out problem. Regards Robby

11-11-2000, 14:41	#6 (permalink)
timitiz Freak Poster Join Date: Jul 2000 Location: Zaandam, the netherlands Posts: 263 Member: 1715 Status: Offline Thanks Meter: 0	Thanks Robby for your answer... But only one thing now... is it also possible to reprogram eprom with pony prog? Greetingz & Thanks again... Timitiz..

11-11-2000, 14:44	#7 (permalink)
Robby VIP-Member Join Date: Jun 1999 Location: Athens, Greece Posts: 214 Member: 254 Status: Offline Thanks Meter: 7	Yes very easy. Everytime you flash eeprom you reprogramme it, from the begining. You can also erase it, and have it blank. Regards Robby

11-11-2000, 14:48	#8 (permalink)
timitiz Freak Poster Join Date: Jul 2000 Location: Zaandam, the netherlands Posts: 263 Member: 1715 Status: Offline Thanks Meter: 0	Thanks Robby.. I'll try it tonight, and will let you know the results... Greetingz Timitiz..

11-15-2000, 00:59	#9 (permalink)
mobileman Cheater -Don't Deal with him- Join Date: Oct 2000 Location: mobile Age: 55 Posts: 1,937 Member: 2399 Status: Offline Thanks Meter: 747	robby, please send me pony programmer, and basic info/guidlines...thanks..