3650 won't boot after I flashed it... - GSM-Forum

GeeZuZz · 05-10-2004, 01:18

I flashed a 3650 for the first time using my Prodigy Clone. I flashed it with 4.13, and there were no errors.

But when i power it on, the Nokia text is shown, and then it fades into white (like it does when it crashes), before the nokia text is shown again a few seconds later. This loops a few times before it shut itself down.

When i power it on when connected to prodigy, it turns it self off about 2 seconds after i power it on, so i can't do any resets or other repair functions using prodigy.

What should i do?

Royslade · 05-10-2004, 06:06

Check the 3,3 K resistor the BSI line in your service battery.

BR Roy

GeeZuZz · 05-10-2004, 19:52

As far as i understand, it's a known problem on Prodigy and v4.13 - so i need to flash it with a older flash.

The problem is that i can't find v3.16...

Royslade · 05-10-2004, 20:00

Check the 3,3K resistor in the service battery

BR Roy

GeeZuZz · 05-10-2004, 22:47

Is this correct? (see attached image)

**Freestyler2000** · 05-10-2004, 23:38

Hi GeeZuZz,

This problem is not realted with the hardware.
The resistor inside the service cable is for auto power.
It is 10 K and is connected between power "+" and BSI.
Then there is a 100 ohm resistor in series on BSI to the Prodigy.
That is if you want to have auto power on any 3 pin battery phone.

Your problem is related with the upgrade from older version to 4.13.
This can only be solved with format user area in "Phone Reset" menu.
Unfortunately this does not work on the version you have installed on your computer.
If you want this working, you will need to convert the clone to be able to work on the
latest updates available - currently 750 at the momnet.

Best regards
Daniel

GeeZuZz · 05-11-2004, 19:45

Freestyler2000: Thank you for replying!

I got the problem solved, by flashing 3.16 instead. Too bad i can't test 4.13 though...

05-10-2004, 01:18	#1 (permalink)
GeeZuZz Freak Poster Join Date: Jun 2002 Posts: 284 Member: 13034 Status: Offline Thanks: 0 Thanked 1 Time in 1 Post	3650 won't boot after I flashed it... I flashed a 3650 for the first time using my Prodigy Clone. I flashed it with 4.13, and there were no errors. But when i power it on, the Nokia text is shown, and then it fades into white (like it does when it crashes), before the nokia text is shown again a few seconds later. This loops a few times before it shut itself down. When i power it on when connected to prodigy, it turns it self off about 2 seconds after i power it on, so i can't do any resets or other repair functions using prodigy. What should i do?

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
thread	Thread Starter	Forum	Replies	Last Post
recovery boot k610 cant flash it	GUDO-GSM	Universalbox	2	11-04-2006 14:57
SmartMoto: V220 only starts in Flash mode, after i flashed it	James_S	Smart-Clip	10	04-07-2005 03:28
3650 "not charging" after i flashed it.	GeeZuZz	Nokia Digital Core Technology 4 ( DCT-4 )	3	05-23-2004 16:09
mc60 won't boot after boot writing??	infogsm	E-Gold Based Phones	1	05-20-2004 19:31

05-10-2004, 06:06	#2 (permalink)
Royslade No Life Poster Join Date: Aug 2002 Age: 46 Posts: 768 Member: 14515 Status: Online Sonork: 100.77248 Thanks: 44 Thanked 15 Times in 11 Posts	Check the 3,3 K resistor the BSI line in your service battery. BR Roy

05-10-2004, 19:52	#3 (permalink)
GeeZuZz Freak Poster Join Date: Jun 2002 Posts: 284 Member: 13034 Status: Offline Thanks: 0 Thanked 1 Time in 1 Post	As far as i understand, it's a known problem on Prodigy and v4.13 - so i need to flash it with a older flash. The problem is that i can't find v3.16...

05-10-2004, 20:00	#4 (permalink)
Royslade No Life Poster Join Date: Aug 2002 Age: 46 Posts: 768 Member: 14515 Status: Online Sonork: 100.77248 Thanks: 44 Thanked 15 Times in 11 Posts	Check the 3,3K resistor in the service battery BR Roy

05-10-2004, 23:38	#6 (permalink)
Freestyler2000 Product Manager Join Date: Dec 2000 Location: UK Posts: 727 Member: 2868 Status: Offline Thanks: 92 Thanked 514 Times in 60 Posts	Hi GeeZuZz, This problem is not realted with the hardware. The resistor inside the service cable is for auto power. It is 10 K and is connected between power "+" and BSI. Then there is a 100 ohm resistor in series on BSI to the Prodigy. That is if you want to have auto power on any 3 pin battery phone. Your problem is related with the upgrade from older version to 4.13. This can only be solved with format user area in "Phone Reset" menu. Unfortunately this does not work on the version you have installed on your computer. If you want this working, you will need to convert the clone to be able to work on the latest updates available - currently 750 at the momnet. Best regards Daniel

05-11-2004, 19:45	#7 (permalink)
GeeZuZz Freak Poster Join Date: Jun 2002 Posts: 284 Member: 13034 Status: Offline Thanks: 0 Thanked 1 Time in 1 Post	Freestyler2000: Thank you for replying! I got the problem solved, by flashing 3.16 instead. Too bad i can't test 4.13 though...