6310 - vibra problem - GSM-Forum

jacck · 10-01-2003, 09:34

I had one 6310 v.4.15 with vibra working only sometimes. I cleaned vibra pads inside and they had very good contact, and vibra motor was OK (tested on battery). After that vibra worked good, but after some time this defect is repeating. Sometimes it works OK, but sometimes vibra no work at all. Squizing of phone makes vibra works. I'm afraid that it is break inside PCB.
Is any solution for repair it ? Which points i should to connect by wires ?

And second problem: when i tryied to repair vibra i tested it with
Nokia Fbus by Maestro v0.25 and vibra now works very weak !
I read this topic: /forum.gsmhosting.com/vbb/showthread.php?threadid=66009
but now it's too late :-(
Is already any free solution for reactivate vibra ?

Medz · 10-04-2003, 02:14

OK
For the 1st problem it is clear that the connection between the
PCB contacts and the motor is bad ( maybe inough to cary volt
but it is not enough to ary curent), U need to scratch the contact
pads on PCB and connectors, raise them and see( can put any
thing under it to keep it raised firmly ).
If that is not working properly unplesent solusion is by wires and
soldreing it directlly!!.
For the 2nd problem U can full flash U'r phn and see.

10-01-2003, 09:34	#1 (permalink)
jacck Major Poster Join Date: Jan 2002 Location: PL Posts: 45 Member: 8856 Status: Offline Thanks: 0 Thanked 2 Times in 2 Posts	6310 - vibra problem I had one 6310 v.4.15 with vibra working only sometimes. I cleaned vibra pads inside and they had very good contact, and vibra motor was OK (tested on battery). After that vibra worked good, but after some time this defect is repeating. Sometimes it works OK, but sometimes vibra no work at all. Squizing of phone makes vibra works. I'm afraid that it is break inside PCB. Is any solution for repair it ? Which points i should to connect by wires ? And second problem: when i tryied to repair vibra i tested it with Nokia Fbus by Maestro v0.25 and vibra now works very weak ! I read this topic: /forum.gsmhosting.com/vbb/showthread.php?threadid=66009 but now it's too late :-( Is already any free solution for reactivate vibra ?

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
thread	Thread Starter	Forum	Replies	Last Post
3310 ring & vibra problem	.:SARCAR:.	Nokia Hardware & Hardware-Repair Area	4	01-22-2007 07:39
t100 vibra problem	MTi-GsM	Samsung Hardware Repair Area	0	04-04-2006 14:21
5210 vibra probleme	stavrosse	Nokia Hardware & Hardware-Repair Area	7	11-17-2005 06:05
6210 insert sim and vibra problem	king22	Nokia Hardware & Hardware-Repair Area	0	09-01-2005 20:46
8910X vibra problem..any solutions..	faysal	Nokia Legacy Phones ( DCT-1 , DCT-2 , DCT-3 , DCT-L )	0	03-21-2005 20:57

10-04-2003, 02:14	#2 (permalink)
Medz No Life Poster Join Date: Sep 2003 Age: 55 Posts: 808 Member: 39601 Status: Offline Thanks: 0 Thanked 13 Times in 11 Posts	OK For the 1st problem it is clear that the connection between the PCB contacts and the motor is bad ( maybe inough to cary volt but it is not enough to ary curent), U need to scratch the contact pads on PCB and connectors, raise them and see( can put any thing under it to keep it raised firmly ). If that is not working properly unplesent solusion is by wires and soldreing it directlly!!. For the 2nd problem U can full flash U'r phn and see.