7210 prototype DEAD - GSM-Forum

jonwillow · 03-28-2003, 08:55

I tryed flash 7210 prototype phone with 4.18 mcu version, now phone dead. old version stayed in phone is p1.89.
Who can help ? Who have p1.89 sw for 7210 ?

Drug_Store · 03-28-2003, 16:24

Quote:

Originally posted by jonwillow
I tryed flash 7210 prototype phone with 4.18 mcu version, now phone dead. old version stayed in phone is 1.20 .
Who can help ? Who have 1.20 sw for 7210 ?

Never heard something from that version (1.20)...

Anyway, flash MCU and then PPM.

Wich devide did you used to make that? Griffin, afd, etc?

Crew · 03-28-2003, 17:01

I've flashed these prototypes
with Neelix and Griffin and 4.18
all ok
Only need to set contrast with Phoenix after
flash finished cause phone will back with empty display

WBR
Crew

Quote:

Originally posted by jonwillow
I tryed flash 7210 prototype phone with 4.18 mcu version, now phone dead. old version stayed in phone is 1.20 .
Who can help ? Who have 1.20 sw for 7210 ?

jonwillow · 03-28-2003, 22:40

Thanks about reply !
I was tried flash phone with free “Cheap flasher” and LP2002 flasher and with original Nokia hardware equipment., I have
Error, in flash area erasing. I can’t put all flash into phone. On 50% flash erasing procedure software show me “Erase Error ”, I tried flash phone with 6610 sw , no problem , flash can stay at phone , but i can’t switch on phone (Phone dead) .
How restore phone ?

really thanks about help!

xpmobile · 04-03-2003, 01:56

Quote:

Originally posted by jonwillow
Thanks about reply !
I was tried flash phone with free “Cheap flasher” and LP2002 flasher and with original Nokia hardware equipment., I have
Error, in flash area erasing. I can’t put all flash into phone. On 50% flash erasing procedure software show me “Erase Error ”, I tried flash phone with 6610 sw , no problem , flash can stay at phone , but i can’t switch on phone (Phone dead) .
I checked all hardware elements, all same as 7210 (original PCB)
How restore phone ?

really thanks about help!

Change UPP and this should solve all your problem

B,R
Alan

xpmobile · 04-03-2003, 01:59

Quote:

Originally posted by Crew
I've flashed these prototypes
with Neelix and Griffin and 4.18
all ok
Only need to set contrast with Phoenix after
flash finished cause phone will back with empty display

WBR
Crew

Use firmware 3.08 and set "Leave Factory Setting" and "Full Factory Setting".

B,R
Alan

jonwillow · 04-06-2003, 12:11

I have changed UPP ,no result

3.08 can't work in my phone

Any solutions ?

xpmobile · 04-06-2003, 19:30

Check if the UPP type is correct. After changing UPP, you have to reflash phones again. I hope that the UEM is still alive ...

B,R
Alan

micmac · 04-06-2003, 19:42

hi,

there is a two solution :

1- chek upp and change it and flash the phone again
2- if upp and uem ok flash this phone with Neelix and all will be ok.

**BLIDA** · 04-07-2003, 09:32

i solved same problem on 3650 prototype v1.43 with griffin first phone was die but tryed with autopower on griffin all was fine .

GSM tools · 04-07-2003, 10:18

I flashed 6610 protype with Griffin, after flash phone had very bad contrast
it's possible repair it with Phoenix

xpmobile · 04-07-2003, 16:20

For Prototype phone, you have to use AFD or neelix2 which having this selected function "Erase User Data". Unclick it. and usually this phone will be safe for flashing. As I can see that the prototype phones has a very sensitive USER DATA (maybe Nokia haven't fully developed it well before release). Try to reflash this phones with its content pack with AFD (Tested well with 6100 and 7210/7250/6610/6310i/3530/3510i)

B,R
Alan

jonwillow · 04-07-2003, 22:11

Here i publish PCB photos (7210 protoyte and orginal)->
http://www.hot.ee/me45/
*high quality.

03-28-2003, 08:55	#1 (permalink)
jonwillow No Life Poster Join Date: Sep 1999 Location: Europe Age: 32 Posts: 909 Member: 461 Status: Offline Thanks: 0 Thanked 3 Times in 3 Posts	7210 prototype DEAD I tryed flash 7210 prototype phone with 4.18 mcu version, now phone dead. old version stayed in phone is p1.89. Who can help ? Who have p1.89 sw for 7210 ? Last edited by jonwillow; 04-07-2003 at 22:15.

03-28-2003, 22:40	#4 (permalink)
jonwillow No Life Poster Join Date: Sep 1999 Location: Europe Age: 32 Posts: 909 Member: 461 Status: Offline Thanks: 0 Thanked 3 Times in 3 Posts	Thanks about reply ! I was tried flash phone with free “Cheap flasher” and LP2002 flasher and with original Nokia hardware equipment., I have Error, in flash area erasing. I can’t put all flash into phone. On 50% flash erasing procedure software show me “Erase Error ”, I tried flash phone with 6610 sw , no problem , flash can stay at phone , but i can’t switch on phone (Phone dead) . How restore phone ? really thanks about help! Last edited by jonwillow; 04-03-2003 at 09:29.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
thread	Thread Starter	Forum	Replies	Last Post
ngage prototype dead after upgrading	jcellgsm	WD2 & APE (Symbian Phones)	4	09-21-2011 09:52
i flashed 7210c with 7210s mobile dead help	pakmobiles	Nokia Base Band 5 ( BB-5 )	6	10-31-2009 18:07
F305 prototype dead after flash	galoml	Cruiser Suite	1	10-11-2009 08:11
K530 GDFS needed ... Prototype Dead	Aamir_Zia	DreamBox	7	03-24-2008 21:46
SG75 Prototyp dead, can't connect Bootloader	THE ZEUS	NON Siemens Brand (ODM Phones)	2	09-05-2007 21:27

04-06-2003, 12:11	#7 (permalink)
jonwillow No Life Poster Join Date: Sep 1999 Location: Europe Age: 32 Posts: 909 Member: 461 Status: Offline Thanks: 0 Thanked 3 Times in 3 Posts	I have changed UPP ,no result 3.08 can't work in my phone Any solutions ?

04-06-2003, 19:30	#8 (permalink)
xpmobile No Life Poster Join Date: Nov 2001 Location: China GuangDong Posts: 1,680 Member: 7220 Status: Offline Thanks: 145 Thanked 1,592 Times in 214 Posts	Check if the UPP type is correct. After changing UPP, you have to reflash phones again. I hope that the UEM is still alive ... B,R Alan

04-06-2003, 19:42	#9 (permalink)
micmac No Life Poster Join Date: Mar 2002 Location: tunis,tunisia Age: 37 Posts: 1,436 Member: 10396 Status: Offline Thanks: 17 Thanked 32 Times in 25 Posts	hi, there is a two solution : 1- chek upp and change it and flash the phone again 2- if upp and uem ok flash this phone with Neelix and all will be ok.

04-07-2003, 09:32	#10 (permalink)
BLIDA Moderator Join Date: Sep 2002 Location: ALGERIA Posts: 1,680 Member: 15439 Status: Offline Sonork: 100.43816 Thanks: 18 Thanked 40 Times in 17 Posts	i solved same problem on 3650 prototype v1.43 with griffin first phone was die but tryed with autopower on griffin all was fine .

04-07-2003, 10:18	#11 (permalink)
GSM tools No Life Poster Join Date: Jun 2002 Location: Czech republic Posts: 581 Member: 12813 Status: Offline Thanks: 9 Thanked 14 Times in 11 Posts	I flashed 6610 protype with Griffin, after flash phone had very bad contrast it's possible repair it with Phoenix

04-07-2003, 16:20	#12 (permalink)
xpmobile No Life Poster Join Date: Nov 2001 Location: China GuangDong Posts: 1,680 Member: 7220 Status: Offline Thanks: 145 Thanked 1,592 Times in 214 Posts	For Prototype phone, you have to use AFD or neelix2 which having this selected function "Erase User Data". Unclick it. and usually this phone will be safe for flashing. As I can see that the prototype phones has a very sensitive USER DATA (maybe Nokia haven't fully developed it well before release). Try to reflash this phones with its content pack with AFD (Tested well with 6100 and 7210/7250/6610/6310i/3530/3510i) B,R Alan

04-07-2003, 22:11	#13 (permalink)
jonwillow No Life Poster Join Date: Sep 1999 Location: Europe Age: 32 Posts: 909 Member: 461 Status: Offline Thanks: 0 Thanked 3 Times in 3 Posts	Here i publish PCB photos (7210 protoyte and orginal)-> http://www.hot.ee/me45/ *high quality.