1202 compatible light / sim card / buzzer ic ??? - GSM-Forum

hooi76 · 03-09-2010, 05:44

can i use 1600 light / sim card / buzzer ic for nokia 1202?

mmmfaruk · 03-09-2010, 07:11

yes brother
thuse ic is same with 1600 and 1202,1661
but kepad ic is not same
i replace light / sim card / buzzer ic from 1202 to 1600 for many tome and successed

for more
plz contect
[email protected]

hooi76 · 03-10-2010, 01:30

thank you, then which ic is compatible for keypad?

HUM · 03-10-2010, 01:47

u can use normal nokia ic

r a nadeem · 03-10-2010, 01:47

Quote:

Originally Posted by hooi76

can i use 1600 light / sim card / buzzer ic for nokia 1202?

Light IC , key pad ic, buzzer IC are same as 1600, but sim IC same as 3110c
someone said that key pad IC is not same , its absolutely wrong ,its lack of knowledge. key pad IC same as 1600-1200-6030-1110-1112-7610-6670 etc. its has 24 pin ESD , check my pis
Rashid Ahmed Nadeem

r a nadeem · 03-10-2010, 01:50

Quote:

Originally Posted by mmmfaruk

yes brother
thuse ic is same with 1600 and 1202,1661
but kepad ic is not same
i replace light / sim card / buzzer ic from 1202 to 1600 for many tome and successed

for more
plz contect
[email protected]

Dear how much knowledge you have ? don't misguide to any person . if you not sure ,
Rashid Ahmed Nadeem

HUM · 03-10-2010, 02:05

sir rashid please give me solution of 1202 no ringer,no speaker,no network and restart
all these problems at the same time
prints are ok
already flash with all versions
reball upp
reball uem and flash ic
still no success

r a nadeem · 03-10-2010, 22:26

Quote:

Originally Posted by HUM

sir rashid please give me solution of 1202 no ringer,no speaker,no network and restart
all these problems at the same time
prints are ok
already flash with all versions
reball upp
reball uem and flash ic
still no success

Dear HUM ,
did you check short at battery terminals , some time when set consume voltage , cause such prob . second 1202 is single layer PCB , and its ways under shield joint , when we remove shield , we lost some prints. they damage due to carelessness , i had repair more then 50 sets
Rashid Ahmed Nadeem

HUM · 03-10-2010, 22:46

respected sir when these sets comes to me its very fresh no shield removed
sir i chk shortage but there is no shortage on terminals
sir u r my senior and i really respect u,can u please tell me how u repair this problem
waiting for reply

mmmfaruk · 03-11-2010, 02:29

Quote:

Originally Posted by r a nadeem

Dear how much knowledge you have ? don't misguide to any person . if you not sure ,
Rashid Ahmed Nadeem

sorry
kepad ic is same but sim ic is not so
i mistake to turn them during write

r a nadeem · 03-11-2010, 22:11

Quote:

Originally Posted by HUM

respected sir when these sets comes to me its very fresh no shield removed
sir i chk shortage but there is no shortage on terminals
sir u r my senior and i really respect u,can u please tell me how u repair this problem
waiting for reply

Dear HUM ,
Thanks for regards ,
i want to know that when it restart. which position .whats its initial position, after flashing it happened , after removing something , or you received set already in this state . plz give me some info about it
Rashid Ahmed Nadeem

Arief Wibowo · 03-11-2010, 22:27

Quote:

Originally Posted by r a nadeem

Dear HUM ,
Thanks for regards ,
i want to know that when it restart. which position .whats its initial position, after flashing it happened , after removing something , or you received set already in this state . plz give me some info about it
Rashid Ahmed Nadeem

DEAR MR NADEEM
help mr nadeem ...
i need PICTURE SMPS JUMPER FOR N90 ..CAN HELP ME??
PHONE IS WHITE SCREEN AND HANG
THANKS BEFORE

HUM · 03-11-2010, 23:27

Quote:

Originally Posted by r a nadeem

Dear HUM ,
Thanks for regards ,
i want to know that when it restart. which position .whats its initial position, after flashing it happened , after removing something , or you received set already in this state . plz give me some info about it
Rashid Ahmed Nadeem

one set recieve in signal problem when manually search set will restart,it also restart when i put on table or some where in standby mode

in this set these actions are taken:

reball upp
reball uem
flash with all versions
i m not changing pa bcoz i face this problem in 1208 (no signal and when search manually set will restart) and i solved by reballing or changing upp so thats why doubtful between upp and pa

one more set recieve in problem of hang,but here i mention one thing problem solved by clean the pcb and lamping,but in uem area i found some dry soldering so i rehot uem and due to dryness of uem and pcb balls set gone dead

i reball uem and set is power on again.................ringer ok,earpiece ok,signal ok i chk with ufone sim it also ok than i i put this set in my draw,after one day when customer comes to recieve his set,there is no ringer,no earpiece,no network and restart problem

i try flashing but no success
write pm but no result

chk selftest

it show same selftest as compare to ok set selftest

also rehot flash ic

but same

5030 no network and restart on manual searching
change pa
rehot upp
rehot flash ic
rehot uem
change all parts related to signal
there is one thing when remove filter restart problem gone but no network still same
already try flashing
write pm
change filter but same

r a nadeem · 03-12-2010, 22:38

Quote:

Originally Posted by Arief Wibowo

DEAR MR NADEEM
help mr nadeem ...
i need PICTURE SMPS JUMPER FOR N90 ..CAN HELP ME??
PHONE IS WHITE SCREEN AND HANG
THANKS BEFORE

remove marked IC and make jumper like in pic
Rashid Ahmed Nadeem

r a nadeem · 03-12-2010, 23:03

Dear HUM
(one set receive in signal problem when manually search set will restart,it also restart when i put on table or some where in standby mode

in this set these actions are taken:

reball upp
reball uem
flash with all versions
i m not changing pa bcoz i face this problem in 1208 (no signal and when search manually set will restart) and i solved by reballing or changing upp so thats why doubtful between upp and pa)

IN this prob fault goes to PA

(one more set recieve in problem of hang,but here i mention one thing problem solved by clean the pcb and lamping,but in uem area i found some dry soldering so i rehot uem and due to dryness of uem and pcb balls set gone dead

i reball uem and set is power on again.................ringer ok,earpiece ok,signal ok i chk with ufone sim it also ok than i i put this set in my draw,after one day when customer comes to recieve his set,there is no ringer,no earpiece,no network and restart problem

i try flashing but no success
write pm but no result

chk selftest

it show same selftest as compare to ok set selftest

also rehot flash ic

but same

Change UEM again , some rust has been create prob. under UEM

(5030 no network and restart on manual searching
change pa
rehot upp
rehot flash ic
rehot uem
change all parts related to signal
there is one thing when remove filter restart problem gone but no network still same
already try flashing
write pm
change filter but same)

in this case change crystal ,
mostly in
1202-1203 1661-1662 -5030 restart , crystal create this prob , i have faced these prob ,
Rashid Ahmed Nadeem

03-09-2010, 05:44	#1 (permalink)
hooi76 No Life Poster Join Date: Dec 2001 Location: In front of my computer Posts: 1,594 Member: 7741 Status: Offline Thanks Meter: 111	1202 compatible light / sim card / buzzer ic ??? can i use 1600 light / sim card / buzzer ic for nokia 1202?

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
5230 boot display SIM card invalid ATF success with good repair!	20442044	Advance-Box	3	06-09-2015 08:56
6300 sim card registration failed!!!	..::khaled::..	Nokia Hardware & Hardware Repair	16	07-19-2011 16:00
w200 compatible light ic	ratan_deb	Sony Ericsson Hardware Repair	0	11-08-2009 08:15
7610 compatible buzzer ic	ratan_deb	Nokia Hardware & Hardware Repair	1	11-07-2009 10:15
Is the K750 buzzer ic compatible with K610 or K618?	hooi76	Sony Ericsson Hardware Repair	4	02-09-2009 13:10

03-09-2010, 07:11	#2 (permalink)
mmmfaruk Freak Poster Join Date: Sep 2009 Posts: 302 Member: 1114923 Status: Offline Thanks Meter: 224	yes brother thuse ic is same with 1600 and 1202,1661 but kepad ic is not same i replace light / sim card / buzzer ic from 1202 to 1600 for many tome and successed for more plz contect [email protected]

03-10-2010, 01:30	#3 (permalink)
hooi76 No Life Poster Join Date: Dec 2001 Location: In front of my computer Posts: 1,594 Member: 7741 Status: Offline Thanks Meter: 111	thank you, then which ic is compatible for keypad?

03-10-2010, 01:47	#4 (permalink)
HUM No Life Poster Join Date: Jul 2005 Location: karachi Posts: 8,673 Member: 161728 Status: Offline Sonork: 100.1582708 Thanks Meter: 2,237	u can use normal nokia ic

03-10-2010, 02:05	#7 (permalink)
HUM No Life Poster Join Date: Jul 2005 Location: karachi Posts: 8,673 Member: 161728 Status: Offline Sonork: 100.1582708 Thanks Meter: 2,237	sir rashid please give me solution of 1202 no ringer,no speaker,no network and restart all these problems at the same time prints are ok already flash with all versions reball upp reball uem and flash ic still no success

03-10-2010, 22:46	#9 (permalink)
HUM No Life Poster Join Date: Jul 2005 Location: karachi Posts: 8,673 Member: 161728 Status: Offline Sonork: 100.1582708 Thanks Meter: 2,237	respected sir when these sets comes to me its very fresh no shield removed sir i chk shortage but there is no shortage on terminals sir u r my senior and i really respect u,can u please tell me how u repair this problem waiting for reply

03-12-2010, 23:03	#15 (permalink)
r a nadeem No Life Poster Join Date: Mar 2006 Location: pakistan Age: 71 Posts: 3,609 Member: 241039 Status: Offline Thanks Meter: 4,170	Dear HUM (one set receive in signal problem when manually search set will restart,it also restart when i put on table or some where in standby mode in this set these actions are taken: reball upp reball uem flash with all versions i m not changing pa bcoz i face this problem in 1208 (no signal and when search manually set will restart) and i solved by reballing or changing upp so thats why doubtful between upp and pa) IN this prob fault goes to PA (one more set recieve in problem of hang,but here i mention one thing problem solved by clean the pcb and lamping,but in uem area i found some dry soldering so i rehot uem and due to dryness of uem and pcb balls set gone dead i reball uem and set is power on again.................ringer ok,earpiece ok,signal ok i chk with ufone sim it also ok than i i put this set in my draw,after one day when customer comes to recieve his set,there is no ringer,no earpiece,no network and restart problem i try flashing but no success write pm but no result chk selftest it show same selftest as compare to ok set selftest also rehot flash ic but same Change UEM again , some rust has been create prob. under UEM (5030 no network and restart on manual searching change pa rehot upp rehot flash ic rehot uem change all parts related to signal there is one thing when remove filter restart problem gone but no network still same already try flashing write pm change filter but same) in this case change crystal , mostly in 1202-1203 1661-1662 -5030 restart , crystal create this prob , i have faced these prob , Rashid Ahmed Nadeem