1202 torch on - GSM-Forum

mehulkr76 · 10-03-2009, 14:28

1202 for repair. when i insert battery torch loght comes on by itself. the fone
is dead does not power on. but no water damage. what can be the problem

waseemking · 10-03-2009, 15:13

uem problem plse change uem 100% your problem solved

manibul · 10-03-2009, 18:27

Change UEM 100000000%

Hariom123 · 10-03-2009, 20:56

antina tip near two compunent just uper section
change this part ya missing this supply so try this ok

tested by me my set 100% ok

try this than post result ok

Hariom

mazmaz1 · 10-03-2009, 22:20

Hello
check uem warming up,
if it warm up very fast,it has faulty uem and you must change it.

mobilecare_titt · 11-11-2009, 05:43

check uem warming ,clean pcb if (water damage) otherwive UEM .

abdul4gsm · 10-18-2010, 19:28

Dear brother customer is not paying so much to replacing the UEM. please any cheap solution.

vinodvava · 10-18-2010, 22:19

re ball uem and clean pcb

10-03-2009, 14:28	#1 (permalink)
mehulkr76 No Life Poster Join Date: Feb 2007 Location: GSM World Posts: 1,169 Member: 457470 Status: Offline Thanks Meter: 159	1202 torch on 1202 for repair. when i insert battery torch loght comes on by itself. the fone is dead does not power on. but no water damage. what can be the problem

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Nokia 1100 torch on	aman.smart	Nokia Hardware & Hardware Repair	1	12-24-2009 19:32
nokia 1100 vibrator and torch on	heera.singh	Nokia Hardware & Hardware Repair	4	11-23-2009 14:24
torch on innokia 1100 and failed to enter local mode	nellabe	Nokia Digital Core Technology 4 ( DCT-4 )	1	12-30-2006 10:53
3200 torch ON goes off with kepad	kobolt	Nokia Hardware & Hardware Repair	4	07-14-2006 11:31
1100 heating & torch on	umeshbhi	Nokia Digital Core Technology 4 ( DCT-4 )	0	04-04-2006 15:59

10-03-2009, 15:13	#2 (permalink)
waseemking Major Poster Join Date: Jun 2009 Posts: 47 Member: 1062917 Status: Offline Thanks Meter: 7	uem problem plse change uem 100% your problem solved

10-03-2009, 18:27	#3 (permalink)
manibul Freak Poster Join Date: Jan 2008 Posts: 378 Member: 675717 Status: Offline Thanks Meter: 125	Change UEM 100000000%

10-03-2009, 20:56	#4 (permalink)
Hariom123 Registered User Join Date: Jul 2008 Location: (India) Age: 41 Posts: 749 Member: 804452 Status: Offline Thanks Meter: 249	antina tip near two compunent just uper section change this part ya missing this supply so try this ok tested by me my set 100% ok try this than post result ok Hariom

10-03-2009, 22:20	#5 (permalink)
mazmaz1 Freak Poster Join Date: Aug 2006 Posts: 477 Member: 339455 Status: Offline Sonork: 100.1589401 Thanks Meter: 86	Hello check uem warming up, if it warm up very fast,it has faulty uem and you must change it.

11-11-2009, 05:43	#6 (permalink)
mobilecare_titt Registered User Join Date: Feb 2008 Location: India Posts: 253 Member: 714467 Status: Offline Sonork: 100.1641520 Thanks Meter: 46	check uem warming ,clean pcb if (water damage) otherwive UEM .

10-18-2010, 19:28	#7 (permalink)
abdul4gsm Junior Member Join Date: Jun 2007 Posts: 37 Member: 520724 Status: Offline Thanks Meter: 349	Dear brother customer is not paying so much to replacing the UEM. please any cheap solution.

10-18-2010, 22:19	#8 (permalink)
vinodvava Insane Poster Join Date: Dec 2007 Location: uae Posts: 88 Member: 658765 Status: Offline Thanks Meter: 13	re ball uem and clean pcb