1600 Contact Service by Changing SIM IC. - GSM-Forum

.:.GSM-ANGEL.:. · 02-03-2008, 10:24

Dear Friends, When I was changing SIM IC of 1600, I got Contact Service in it.. its first time I got. I tried to do via flash I could'nt solved. If any body have correct solution please reply urgent....

Please Help..

acay · 02-03-2008, 10:36

hardware problem! cek if ur phone stanby contant service can shut down if u press on/of its cpu problem!!
if phone stanby contant service can't shut down by press on/of its uem problem!!!
br,
acay

RUVAIZ · 02-03-2008, 12:49

see if it is ok on normal mode by software and contact service by battery than 100% uem problem it is due to overheating

tarunvishal · 02-03-2008, 16:03

brother dip ur phone in petrol for 15 min and after that clean ur pcb or give heat on cpu ur problem is solved 100%

sphameed · 02-03-2008, 17:00

its must be hardware i feel u messed up balls in uem when u changing sim ic hope u gentle heat uem with good paste careful becoz uem moulded
best of luck

sopnil · 02-03-2008, 17:31

hi to all ,
finaly i will lockout this problem . problem is pp file if write same pp file then we can solved this type problem.or others solution is change sim ic then flash or make sim jumper then flash......good luck

.:KHALIFA:. · 02-03-2008, 17:49

Quote:

Originally Posted by .:.GSM-ANGEL.:.

Dear Friends, When I was changing SIM IC of 1600, I got Contact Service in it.. its first time I got. I tried to do via flash I could'nt solved. If any body have correct solution please reply urgent....

Please Help..

as u said u tried with flashing but it din help...
so bro its hardware problem...
first remove that sim n chek ... if contact service gone
than just put another ic....

secondly if the problem still there after removing sim ic ...
than simply reball or change upp...

90% ur problem will b solved with this.. n the 10% is dew to uem

joe cellular · 02-03-2008, 17:56

Quote:

Originally Posted by .:.GSM-ANGEL.:.

Dear Friends, When I was changing SIM IC of 1600, I got Contact Service in it.. its first time I got. I tried to do via flash I could'nt solved. If any body have correct solution please reply urgent....

Please Help..

hi, personally iv stop doin des models,1600,1200,1110 etc cuz da mother boards are very weak, just as if nokia made dem 2 b disposible fones.

.:KHALIFA:. · 02-03-2008, 18:12

Quote:

Originally Posted by joe cellular

hi, personally iv stop doin des models,1600,1200,1110 etc cuz da mother boards are very weak, just as if nokia made dem 2 b disposible fones.

agree with u ....... i stoped repairing these phones
months ago

Jr Telecom · 02-03-2008, 19:05

I agree with @:KHALIFA:
""""""""""""""""""""""""""""""""
while somebody change the sim ic then upp/uem destroyed by high temparature...sometimes by rehot/reball phone will be alive...........

adnanali · 02-03-2008, 19:48

Quote:

Originally Posted by Jr Telecom

I agree with @:KHALIFA:
""""""""""""""""""""""""""""""""
while somebody change the sim ic then upp/uem destroyed by high temparature...sometimes by rehot/reball phone will be alive...........

i agree with you a hard job

GSMTURBO · 02-03-2008, 19:59

brother i have same problem any one have vidio how to reball uem and cpu

Quote:

Originally Posted by adn****i

i agree with you a hard job

GSMTURBO · 02-03-2008, 20:04

and what is upp....

gokul2005 · 02-04-2008, 05:39

Quote:

Originally Posted by .:.GSM-ANGEL.:.

Dear Friends, When I was changing SIM IC of 1600, I got Contact Service in it.. its first time I got. I tried to do via flash I could'nt solved. If any body have correct solution please reply urgent....

Please Help..

After removing Sim IC u got ContactService its 99% UEM problem...

mobilelink · 02-04-2008, 06:15

Agree with al mates (CS due to over heating)

100% hardware bro.try da solution above n if nt bad luck.pointless spending time for a phone like 1600 for more than that.try to replace a pcb

Cheers'

View Poll Results: Contact Service -- Harware or Software.
Hardware	1,316	59.82%
Software	271	12.32%
Both	613	27.86%
Voters: 2200. You may not vote on this poll

02-03-2008, 10:24	#1 (permalink)
.:.GSM-ANGEL.:. Banned Join Date: Jun 2004 Location: GSM HEAVEN Age: 36 Posts: 329 Member: 69984 Status: Offline Thanks Meter: 170	1600 Contact Service by Changing SIM IC. Dear Friends, When I was changing SIM IC of 1600, I got Contact Service in it.. its first time I got. I tried to do via flash I could'nt solved. If any body have correct solution please reply urgent.... Please Help..

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
1600 contact service and invalid sim	HUM	Nokia Hardware & Hardware Repair	12	12-11-2010 07:04
1110 contact service by changing sim ic	Options Media	Nokia Hardware & Hardware Repair	2	07-29-2009 15:25
1110 contact service after chang sim ic	Elias Khan	Nokia Hardware & Hardware Repair	1	06-13-2009 13:57
1112 & 1600 contact service/sim not valid	.:SARCAR:.	Nokia Hardware & Hardware Repair	2	06-16-2008 07:08

02-03-2008, 10:36	#2 (permalink)
acay Freak Poster Join Date: Nov 2005 Posts: 444 Member: 197916 Status: Offline Thanks Meter: 157	hardware problem! cek if ur phone stanby contant service can shut down if u press on/of its cpu problem!! if phone stanby contant service can't shut down by press on/of its uem problem!!! br, acay

02-03-2008, 12:49	#3 (permalink)
RUVAIZ Freak Poster Join Date: Oct 2007 Location: KHANDWA INDIA Age: 40 Posts: 161 Member: 618734 Status: Offline Thanks Meter: 56	see if it is ok on normal mode by software and contact service by battery than 100% uem problem it is due to overheating

02-03-2008, 16:03	#4 (permalink)
tarunvishal No Life Poster Join Date: Jul 2006 Posts: 833 Member: 308296 Status: Offline Thanks Meter: 152	brother dip ur phone in petrol for 15 min and after that clean ur pcb or give heat on cpu ur problem is solved 100%

02-03-2008, 17:00	#5 (permalink)
sphameed Freak Poster Join Date: Nov 2007 Location: India/Malaysia Posts: 441 Member: 641058 Status: Offline Sonork: 100.1589325 Thanks Meter: 140	its must be hardware i feel u messed up balls in uem when u changing sim ic hope u gentle heat uem with good paste careful becoz uem moulded best of luck

02-03-2008, 17:31	#6 (permalink)
sopnil No Life Poster Join Date: Jun 2007 Location: dhaka,bangladesh Posts: 790 Member: 528679 Status: Offline Thanks Meter: 268	hi to all , finaly i will lockout this problem . problem is pp file if write same pp file then we can solved this type problem.or others solution is change sim ic then flash or make sim jumper then flash......good luck

02-03-2008, 19:05	#10 (permalink)
Jr Telecom No Life Poster Join Date: Dec 2006 Location: Jr Telecom™ Posts: 1,735 Member: 409725 Status: Offline Sonork: 100.1581478 Thanks Meter: 797	I agree with @:KHALIFA: """""""""""""""""""""""""""""""" while somebody change the sim ic then upp/uem destroyed by high temparature...sometimes by rehot/reball phone will be alive...........

02-03-2008, 20:04	#13 (permalink)
GSMTURBO No Life Poster Join Date: Mar 2007 Location: (UAE)(pak) Posts: 1,874 Member: 479496 Status: Offline Sonork: 1592751 Thanks Meter: 404	and what is upp....

02-04-2008, 06:15	#15 (permalink)
mobilelink No Life Poster Join Date: Jul 2006 Location: UK Age: 45 Posts: 532 Member: 318277 Status: Offline Thanks Meter: 92	Agree with al mates (CS due to over heating) 100% hardware bro.try da solution above n if nt bad luck.pointless spending time for a phone like 1600 for more than that.try to replace a pcb Cheers'