1600 no incoming call voice - GSM-Forum

nitis009 · 12-06-2010, 17:19

in a 1600 ring ok in call loudspaker working but no incoming voice change ringer ic, change a ic upper on ringer ic. , make jumper but same anyone help m

nitis009 · 12-07-2010, 08:08

plz help m any master

DIPU04 · 12-07-2010, 08:27

1.change a new charging connector.
2.cheque ringer driver(8 leg tr) for broken or its print damage.
3. change ringer ic.

nitis009 · 12-07-2010, 10:37

Quote:

Originally Posted by DIPU04

1.change a new charging connector.
2.cheque ringer driver(8 leg tr) for broken or its print damage.
3. change ringer ic.

bro. allready change all this but same condition

r a nadeem · 12-08-2010, 02:36

Quote:

Originally Posted by nitis009

in a 1600 ring ok in call loudspaker working but no incoming voice change ringer ic, change a ic upper on ringer ic. , make jumper but same anyone help m

Quote:

Originally Posted by nitis009

plz help m any master

Quote:

Originally Posted by nitis009

bro. allready change all this but same condition

if you try all solution then check its 10 ohm resistor

Rashid Ahmed Nadeem

bruightmobile · 12-08-2010, 20:05

its 100% uem problem rehot uem carefully put some rubber packing on uem and check after all change uem "if u can" post reply

12-06-2010, 17:19	#1 (permalink)
nitis009 Freak Poster Join Date: Jul 2010 Posts: 272 Member: 1343713 Status: Offline Thanks Meter: 26	1600 no incoming call voice in a 1600 ring ok in call loudspaker working but no incoming voice change ringer ic, change a ic upper on ringer ic. , make jumper but same anyone help m

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
My 6150 (5.23) No network after Flashing	AboAli	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	0	01-31-2001 15:56
6150 no outgoing calls	edis	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	1	07-20-2000 20:19
Nokia 6110 without net. couldn´t call 911 either!	DennisT	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	3	05-09-2000 11:37
no one can unlock 6110 05.40 25-5-99	fondas	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	8	09-22-1999 08:03

12-07-2010, 08:08	#2 (permalink)
nitis009 Freak Poster Join Date: Jul 2010 Posts: 272 Member: 1343713 Status: Offline Thanks Meter: 26	plz help m any master

12-07-2010, 08:27	#3 (permalink)
DIPU04 Freak Poster Join Date: Nov 2007 Location: orissa Posts: 108 Member: 628191 Status: Offline Thanks Meter: 13	1.change a new charging connector. 2.cheque ringer driver(8 leg tr) for broken or its print damage. 3. change ringer ic.

12-08-2010, 20:05	#6 (permalink)
bruightmobile Registered User Join Date: Aug 2009 Posts: 668 Member: 1087294 Status: Offline Thanks Meter: 252	its 100% uem problem rehot uem carefully put some rubber packing on uem and check after all change uem "if u can" post reply