How to dry 3310 after dipping into ultrasonic solution! - GSM-Forum

MC Harami · 10-27-2004, 23:47

I have dipped my 3310 PCB board into ultrasonic solution but the board is soaking wet and i need to know how u r suppose to dry it quickly because it is taken ages to do?

pazeth™ · 10-28-2004, 05:49

used alcohol to dipped pcb, after that dry using hair dryer of hotair

MC Harami · 10-29-2004, 01:10

what temperature do i need to set the hot air too?
Also do i re-heat every component on the board or is there certain ones i shouldnt touch?

pazeth™ · 10-29-2004, 05:36

easy, use hotair on 5 heater and 5 air and 5 cm from pcb for all componen with swinging for 10-15 minute

leosedf · 10-29-2004, 07:15

I use compressed air to remove most of the liquid and maybe alcohol and then hot air about 150-200 degrees for a short time

bungle_uk · 10-29-2004, 07:20

Do not use household hairdryer because of the ionised particles, always use hot air gun for drying as pazeth said

Mobile Master Pk · 10-29-2004, 19:49

ctc is best for pcb for all another oile for this perpuse

10-27-2004, 23:47	#1 (permalink)
MC Harami No Life Poster Join Date: Jan 2004 Location: Peh Bhooti, Pakistan Age: 41 Posts: 673 Member: 49896 Status: Offline Thanks Meter: 14	How to dry 3310 after dipping into ultrasonic solution! I have dipped my 3310 PCB board into ultrasonic solution but the board is soaking wet and i need to know how u r suppose to dry it quickly because it is taken ages to do?

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
How to enter the unlock code into a CL75?	The Repair Shop	NON Siemens Brand (ODM Phones)	5	07-16-2010 04:09
how to change 3585i non-ruim into ruim one ?	genocite	Nokia CDMA	2	05-20-2006 17:47
How to convert '.EYE' extention into .avi or .3gp???	godisgreat	Nokia Digital Core Technology 4 ( DCT-4 )	2	03-03-2005 06:13
How to flash Chinese language pack into a UK C350?	nowgsm	Motorola P2k	0	09-30-2004 14:39
how to enter the unlock code into a alcatel	JOHN_BOY_06	Alcatel & TCL Old Models	2	09-20-2004 23:20

10-28-2004, 05:49	#2 (permalink)
pazeth™ No Life Poster Join Date: Jul 2004 Location: BANDA ACEH INDONESIA Posts: 1,268 Member: 74519 Status: Offline Thanks Meter: 79	used alcohol to dipped pcb, after that dry using hair dryer of hotair

10-29-2004, 01:10	#3 (permalink)
MC Harami No Life Poster Join Date: Jan 2004 Location: Peh Bhooti, Pakistan Age: 41 Posts: 673 Member: 49896 Status: Offline Thanks Meter: 14	what temperature do i need to set the hot air too? Also do i re-heat every component on the board or is there certain ones i shouldnt touch?

10-29-2004, 05:36	#4 (permalink)
pazeth™ No Life Poster Join Date: Jul 2004 Location: BANDA ACEH INDONESIA Posts: 1,268 Member: 74519 Status: Offline Thanks Meter: 79	easy, use hotair on 5 heater and 5 air and 5 cm from pcb for all componen with swinging for 10-15 minute

10-29-2004, 07:15	#5 (permalink)
leosedf No Life Poster Join Date: Jul 2003 Location: Thessaloniki,Hellas Age: 44 Posts: 1,013 Member: 33547 Status: Offline Thanks Meter: 17	I use compressed air to remove most of the liquid and maybe alcohol and then hot air about 150-200 degrees for a short time

10-29-2004, 07:20	#6 (permalink)
bungle_uk No Life Poster Join Date: Jan 2004 Age: 53 Posts: 4,956 Member: 51154 Status: Offline Thanks Meter: 68	Do not use household hairdryer because of the ionised particles, always use hot air gun for drying as pazeth said

10-29-2004, 19:49	#7 (permalink)
Mobile Master Pk No Life Poster Join Date: May 2004 Location: M Arshed Khan Age: 55 Posts: 577 Member: 66225 Status: Offline Thanks Meter: 9	ctc is best for pcb for all another oile for this perpuse