6600 gallery hang - GSM-Forum

prmzin · 05-16-2005, 19:10

hi
i have nokia 6600 which hangs on opening gallery and shows media thread error . required a solustion to this problem if anyone
thanx in adv

pazeth™ · 05-16-2005, 20:21

this is step to repair your phone:

1. remove SIMcard and MMC.
2. install full battery
3. press 3 key together: call (green) key, *(star key), number 3 key and press power buttom, do not move your hand and let screen show " formating..." now your problem slove, if not go to point 4
4. connect phone to griffin box - detect phone- format user area, after format OK it means all have been OK, if not go to point 5
5. erase flash with 6600_fullerase.fia ( do not choice MCU flashing!!!! it means flash PPM only), after eraseflash complete griffin asked for power on phone manualy and select NO, now your phone is dead.
6. make fullflash ( MCU-PPM-PM) unlock - format user area again one more time if phone can't flash go to point 8
7. now your phone is OK, if not go to point 8
8. check hardware device, flash IC and Bluetooth module ( I'm not so good in hardware so I'm not sure for point 8)

good luck brother,

pazeth

gsmbun · 05-16-2005, 20:38

Check Your Bluetooth Section

imran_qasim · 05-16-2005, 20:53

just try to restore factory default setting by etnering the code *#7370#

NOTE
bettry shld b full
remove SIM
remove MMC card

take care

pazeth™ · 05-17-2005, 05:08

Quote:

Originally Posted by imran_qasim

just try to restore factory default setting by etnering the code *#7370#

NOTE
bettry shld b full
remove SIM
remove MMC card

take care

you can't enter code like that without SIM card......

imran_qasim · 05-17-2005, 08:18

@pazeth
sorry
yes i forgott to correct it
thnx

jepor · 05-17-2005, 20:49

Hi all....
Until today i can't look and hear if the case can be repaired by someone (correct if i'm wrong???). But some people just said to check BT and Flash IC. Maybe they forgot how to take BT coz' i have same cases like that and when i looked the BT is difficult to put up.

If anybody already test to repaired this cases pls share this Forum how to repair and step by step procedure to repair.

T'x

.:*CHENNAI GSM*:. · 05-18-2005, 08:30

Myself cured a couple of mobiles with these problem.

case I

If you try flashing it with UFS and the BT flashing enabled you will get cbus error, you will be able to flash the phone by unchecking the BT flashing enabled box but the problem will persist, That means the BT module is faulty you need to change it and flash and it will be ok.

Case II

If you flash it with UFS and the BT flashing enabled you will be able to flash but the problem will persist that means your upp or uem is faulty. You need to check with that and try flashing again should work.

Thanx for reading

Regards

abadon · 05-18-2005, 08:36

use format user area with GRIFFIN BOX
use *#7370# format wour phone
use * + 3 + green buton + power buton

Regards

imran_qasim · 05-18-2005, 08:41

Quote:

Originally Posted by abadon

use format user area with GRIFFIN BOX
use *#7370# format wour phone
use * + 3 + green buton + power buton

Regards

dont try to increase your posts like this these solutions are already discussed
take care

ihsanali · 05-18-2005, 09:01

all theese methods tried on more than 5 sets but no success

Raheeeeb · 05-18-2005, 23:38

Quote:

Originally Posted by ihsanali

all theese methods tried on more than 5 sets but no success

change bluetooth module

100% working
but you must do hardware good
i recommend use of solder iron not hotair at all

br.,

raheeeeb

gsmservices · 07-16-2005, 16:59

hi,
re-solder the blue tooth ic with the iron and use hot air gun after that and then re-flash it with the latest ver. of 6600. phone works 10000000 %,
take care ,
nitin

jepor · 07-19-2005, 07:18

Quote:

Originally Posted by raheeeeb

change bluetooth module

100% working
but you must do hardware good
i recommend use of solder iron not hotair at all

br.,

raheeeeb

Yes U are... but how to put up the BT IC??? Coz the BT IC is difficult to put up BOSS... I think must used some liquid (special???) for take it and solder it again.

Just Use Solder Iron for put up it??? Who tested this methode????

T'x boss...

benguetcowboy1 · 07-19-2005, 18:19

hehehehehehe maybe he counted how many pins are there in the BT module and used same number of soldering iron at the same time to loosen and remove the module!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

05-16-2005, 19:10	#1 (permalink)
prmzin Freak Poster Join Date: Feb 2004 Age: 45 Posts: 165 Member: 54900 Status: Offline Thanks Meter: 11	6600 gallery hang hi i have nokia 6600 which hangs on opening gallery and shows media thread error . required a solustion to this problem if anyone thanx in adv

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
6600 browsing gallery hang cant open bt	gsm8g	Nokia Hardware & Hardware Repair	57	06-22-2011 19:49
6600 Gallery Problem	shaikhboy	WD2 & APE (Symbian Phones)	39	11-22-2009 08:04
6600 gallery not open	HUM	Nokia Hardware & Hardware Repair	4	10-21-2005 20:37
6600 gallery	hassan1975	Nokia Hardware & Hardware Repair	2	10-27-2004 10:56
Above Connection`s 6600 Gallery!	aboveconnection	WD2 & APE (Symbian Phones)	11	12-17-2003 23:51

05-16-2005, 20:21	#2 (permalink)
pazeth™ No Life Poster Join Date: Jul 2004 Location: BANDA ACEH INDONESIA Posts: 1,268 Member: 74519 Status: Offline Thanks Meter: 79	this is step to repair your phone: 1. remove SIMcard and MMC. 2. install full battery 3. press 3 key together: call (green) key, *(star key), number 3 key and press power buttom, do not move your hand and let screen show " formating..." now your problem slove, if not go to point 4 4. connect phone to griffin box - detect phone- format user area, after format OK it means all have been OK, if not go to point 5 5. erase flash with 6600_fullerase.fia ( do not choice MCU flashing!!!! it means flash PPM only), after eraseflash complete griffin asked for power on phone manualy and select NO, now your phone is dead. 6. make fullflash ( MCU-PPM-PM) unlock - format user area again one more time if phone can't flash go to point 8 7. now your phone is OK, if not go to point 8 8. check hardware device, flash IC and Bluetooth module ( I'm not so good in hardware so I'm not sure for point 8) good luck brother, pazeth

05-16-2005, 20:38	#3 (permalink)
gsmbun No Life Poster Join Date: Jan 2002 Location: india/saudi arabia Posts: 541 Member: 9013 Status: Offline Thanks Meter: 15	Check Your Bluetooth Section

05-16-2005, 20:53	#4 (permalink)
imran_qasim No Life Poster Join Date: Apr 2005 Location: PAKISTAN Age: 45 Posts: 1,790 Member: 133436 Status: Offline Sonork: 100.1577364 Thanks Meter: 191	just try to restore factory default setting by etnering the code *#7370# NOTE bettry shld b full remove SIM remove MMC card take care

05-17-2005, 08:18	#6 (permalink)
imran_qasim No Life Poster Join Date: Apr 2005 Location: PAKISTAN Age: 45 Posts: 1,790 Member: 133436 Status: Offline Sonork: 100.1577364 Thanks Meter: 191	@pazeth sorry yes i forgott to correct it thnx

05-17-2005, 20:49	#7 (permalink)
jepor Freak Poster Join Date: Dec 2004 Location: Tobek of Papua'x Age: 39 Posts: 134 Member: 97261 Status: Offline Thanks Meter: 0	Hi all.... Until today i can't look and hear if the case can be repaired by someone (correct if i'm wrong???). But some people just said to check BT and Flash IC. Maybe they forgot how to take BT coz' i have same cases like that and when i looked the BT is difficult to put up. If anybody already test to repaired this cases pls share this Forum how to repair and step by step procedure to repair. T'x

05-18-2005, 08:30	#8 (permalink)
.:CHENNAI GSM:. Freak Poster Join Date: Jan 2002 Location: India Age: 48 Posts: 282 Member: 8587 Status: Offline Thanks Meter: 4	Myself cured a couple of mobiles with these problem. case I If you try flashing it with UFS and the BT flashing enabled you will get cbus error, you will be able to flash the phone by unchecking the BT flashing enabled box but the problem will persist, That means the BT module is faulty you need to change it and flash and it will be ok. Case II If you flash it with UFS and the BT flashing enabled you will be able to flash but the problem will persist that means your upp or uem is faulty. You need to check with that and try flashing again should work. Thanx for reading Regards

05-18-2005, 08:36	#9 (permalink)
abadon Freak Poster Join Date: Apr 2005 Location: somewhere in the darkness Age: 43 Posts: 417 Member: 134869 Status: Offline Thanks Meter: 8	use format user area with GRIFFIN BOX use #7370# format wour phone use + 3 + green buton + power buton Regards

05-18-2005, 09:01	#11 (permalink)
ihsanali No Life Poster Join Date: Mar 2003 Location: pakistan Age: 45 Posts: 717 Member: 23939 Status: Offline Thanks Meter: 14	all theese methods tried on more than 5 sets but no success

07-16-2005, 16:59	#13 (permalink)
gsmservices No Life Poster Join Date: Dec 2004 Age: 48 Posts: 790 Member: 101827 Status: Offline Thanks Meter: 23	hi, re-solder the blue tooth ic with the iron and use hot air gun after that and then re-flash it with the latest ver. of 6600. phone works 10000000 %, take care , nitin

07-19-2005, 18:19	#15 (permalink)
benguetcowboy1 No Life Poster Join Date: Feb 2004 Location: Baguio_City;Ph @ DrunkenMaster Age: 44 Posts: 1,916 Member: 51716 Status: Offline Sonork: 100.1594676 Thanks Meter: 217	hehehehehehe maybe he counted how many pins are there in the BT module and used same number of soldering iron at the same time to loosen and remove the module!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!