8310 can not power on when put batt - GSM-Forum

watch man · 12-02-2002, 08:45

pls help. 8310 can be flashing but when put the batt can not powered on, batt connector allready check, is ok...

VELIKI · 12-02-2002, 11:47

try to flash one more time if bat is full and you can flash the phone than is somethin small you must find out

Neo777 · 12-02-2002, 17:00

so .. verify if you have 3.8v on the pressed power button .. with battery ..

sawa · 12-03-2002, 00:16

i had same problem...and i downgraded version....till i find one that powered my 8310...i do not wny but ......tryyyyy

watch man · 12-08-2002, 20:04

sawa
thanks but it still not powerd on, I downgrade to any version I have still off....

Neo777
I will try it, thanks

olsa · 12-09-2002, 02:13

try to flash with ver. 5.54 or 5.57 (mcu + ppm)

RAMZY · 12-09-2002, 02:36

hi
try to remove 15 min (quartz) 26Mhz and put it again

100 % for me 3 times

Have Fun

12-02-2002, 08:45	#1 (permalink)
watch man Freak Poster Join Date: Nov 1999 Location: South East Asia Posts: 203 Member: 662 Status: Offline Thanks Meter: 0	8310 can not power on when put batt pls help. 8310 can be flashing but when put the batt can not powered on, batt connector allready check, is ok...

12-02-2002, 17:00	#3 (permalink)
Neo777 Freak Poster Join Date: May 2002 Location: Craiova, RO. Age: 51 Posts: 159 Member: 11493 Status: Offline Thanks Meter: 0	verify .. so .. verify if you have 3.8v on the pressed power button .. with battery ..

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
nokia 6500s it comes on when charging but dose not power on when u press on	4 u man	Nokia Hardware & Hardware Repair	3	04-06-2009 20:29
Solucion for My x1 x2 x5 .... Charging without Charger and power On When Put Batery	Mierdita	Sagem Hardware Repair Area	22	08-23-2008 19:31
N76 Auto power on when Put Battery !	foreverlovetn	Nokia Base Band 5 ( BB-5 )	1	04-28-2008 13:40
Help...j200i Auto Power On When Put Battery	CHAPRAN	Sony Ericsson Hardware Repair	4	03-25-2007 19:19
t100 not power on after flash, not power on when original cable is plug	GYZMO	VLSI, Conexant, Skyworks and Old Models	8	01-07-2004 00:34

12-02-2002, 11:47	#2 (permalink)
VELIKI No Life Poster Join Date: Nov 2002 Location: slovenia Age: 48 Posts: 589 Member: 18028 Status: Offline Thanks Meter: 20	try to flash one more time if bat is full and you can flash the phone than is somethin small you must find out

12-03-2002, 00:16	#4 (permalink)
sawa Freak Poster Join Date: Oct 2001 Location: NIS Posts: 251 Member: 6781 Status: Offline Thanks Meter: 0	i had same problem...and i downgraded version....till i find one that powered my 8310...i do not wny but ......tryyyyy

12-08-2002, 20:04	#5 (permalink)
watch man Freak Poster Join Date: Nov 1999 Location: South East Asia Posts: 203 Member: 662 Status: Offline Thanks Meter: 0	sawa thanks but it still not powerd on, I downgrade to any version I have still off.... Neo777 I will try it, thanks

12-09-2002, 02:13	#6 (permalink)
olsa Junior Member Join Date: Dec 2001 Location: Podgorica-YUGOSLAVIA Age: 51 Posts: 23 Member: 7919 Status: Offline Thanks Meter: 0	try to flash with ver. 5.54 or 5.57 (mcu + ppm)

12-09-2002, 02:36	#7 (permalink)
RAMZY Junior Member Join Date: Sep 2002 Location: EUR Age: 48 Posts: 16 Member: 15977 Status: Offline Thanks Meter: 0	hi try to remove 15 min (quartz) 26Mhz and put it again 100 % for me 3 times Have Fun