Damaged solder pads ? Is there any way to repair them ? - GSM-Forum

simbirley · 01-21-2003, 15:23

People keep asking me if i can repair damaged solder pads where leds have been ripped off the board or where power switches have been pulled off.

Is there anyway to make the solder stick to the contact ?

Burnt Cobba · 01-21-2003, 16:08

one way to do it is use some super glue to stick the new acting pad. This however is according to where you are using it. If it is the switch then it msut be strongly and firmly held else it wil lgive way.

g luck
al

baraka42 · 01-21-2003, 18:15

hi burnt ?

super glue is conductive ? what about connection from

x y z part ?

to simbirley,

i use diod's or resister's thick wire. one side at pcb's ground

and other at switche's ground leg. then second to supply

and then super glue.

willy · 01-21-2003, 20:27

simbirley
might you have to search it first . and you can read this:
http://forum.gsmhosting.com/vbb/show...threadid=68845

Willy

Quote:

Originally posted by simbirley
People keep asking me if i can repair damaged solder pads where leds have been ripped off the board or where power switches have been pulled off.

Is there anyway to make the solder stick to the contact ?

01-21-2003, 15:23	#1 (permalink)
simbirley Freak Poster Join Date: Apr 2001 Posts: 353 Member: 4398 Status: Offline Thanks Meter: 1	Damaged solder pads ? Is there any way to repair them ? People keep asking me if i can repair damaged solder pads where leds have been ripped off the board or where power switches have been pulled off. Is there anyway to make the solder stick to the contact ?

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
CONFIG KEY: 0000000000000000 is there any way to repair this!	ATSC L.L.C	Universalbox	8	03-20-2009 09:17
CONFIG KEY: 0000000000000000 is there any way to repair this!	ATSC L.L.C	J.A.F. By Jafsupport.com	0	01-21-2009 14:04
Is there any way to repair imei on M6100?	Burnt Cobba	VygisToolbox	3	11-25-2007 21:28
Is there any way to repair "Contact Service" Using Dejan Flasher.?	AboAli	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	6	04-26-2001 03:41
Is there any way to repair "Contact Service" Using Dejan Flasher	AboAli	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	3	04-19-2001 22:08

01-21-2003, 16:08	#2 (permalink)
Burnt Cobba No Life Poster Join Date: Apr 2002 Location: The Green Mile Posts: 3,653 Member: 11325 Status: Offline Thanks Meter: 266	one way to do it is use some super glue to stick the new acting pad. This however is according to where you are using it. If it is the switch then it msut be strongly and firmly held else it wil lgive way. g luck al

01-21-2003, 18:15	#3 (permalink)
baraka42 No Life Poster Join Date: Aug 2002 Location: india Age: 63 Posts: 1,476 Member: 14578 Status: Offline Thanks Meter: 831	hi burnt ? super glue is conductive ? what about connection from x y z part ? to simbirley, i use diod's or resister's thick wire. one side at pcb's ground and other at switche's ground leg. then second to supply and then super glue.