Dead 3310 (New CCONT) - GSM-Forum

Fuse · 06-24-2003, 19:57

Totally Dead 3310........ Tried to flash. Flashed 70% almost ok but unable to update Faid, so flash is not completed........Checked power on/off switch ok, checked C227 & 228 = 3.6volts ok. Checked R224 but power is low less than 3.6 volts. Reflowed CCONT then replaced CCONT (brand new). Phone still dead. Any ideas please. No sign of any water damage board looks very clean.

Fuse

kulibin · 06-24-2003, 22:55

If don't work update FAID may be this is COBBA

Zoolee · 06-25-2003, 07:29

Hi!

Try change cobba, and full flash, update faid.

Good Luck

B.R.

MrHazeem · 06-25-2003, 08:30

Also may be this is a flash ic problem or proken soldering under it ...!

i met this before and solved after reball flash ic ...

06-24-2003, 19:57	#1 (permalink)
Fuse Junior Member Join Date: May 2003 Location: Sussex Age: 66 Posts: 35 Member: 28964 Status: Offline Thanks Meter: 0	Dead 3310 (New CCONT) Totally Dead 3310........ Tried to flash. Flashed 70% almost ok but unable to update Faid, so flash is not completed........Checked power on/off switch ok, checked C227 & 228 = 3.6volts ok. Checked R224 but power is low less than 3.6 volts. Reflowed CCONT then replaced CCONT (brand new). Phone still dead. Any ideas please. No sign of any water damage board looks very clean. Fuse

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
dead 3310 due to corrupt fullflash	ambot	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	4	12-14-2001 17:10
Dead 3310 ver. 4.18 please help	Meam	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	13	04-30-2001 19:11
DEAD 3310 :rolleyes:	CyberMania	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	6	04-13-2001 13:56
Another dead 3310 "phone ram is bad"	CyberKareca	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	2	04-04-2001 01:06
dead 3310 after wrong unlock	PADERF	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	0	03-26-2001 21:27

06-24-2003, 22:55	#2 (permalink)
kulibin Freak Poster Join Date: Oct 2002 Age: 41 Posts: 423 Member: 16452 Status: Offline Thanks Meter: 4	If don't work update FAID may be this is COBBA

06-25-2003, 07:29	#3 (permalink)
Zoolee Freak Poster Join Date: Feb 2003 Location: Miami Posts: 149 Member: 22526 Status: Offline Thanks Meter: 1	Hi! Try change cobba, and full flash, update faid. Good Luck B.R.

06-25-2003, 08:30	#4 (permalink)
MrHazeem Freak Poster Join Date: Jul 2002 Location: MAD Age: 50 Posts: 483 Member: 13545 Status: Offline Thanks Meter: 2	Also may be this is a flash ic problem or proken soldering under it ...! i met this before and solved after reball flash ic ...