Help about UFS3 - GSM-Forum

VinhHai · 03-28-2005, 05:02

Hi USF team

I have just changed UEM and when I flash N6100 and I see:

"1st Boot Ok, DCT4, UPP: 1120
2nd Boot Error: 2
Platform: 3, Error Data:
E3 72 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Process Failed, Repowering Mobile"

I've rehot Flash IC and UPP but nothing change, when I choose "CHECK" I see nomaly. What 's it mean? Pls help me.

Thks

bengkel_hp · 03-28-2005, 17:55

i found the problem too, you can resolved the problem with change upp ic or flash ic.

imam · 03-28-2005, 20:19

i think the flash ic first, because "1st Boot Ok, DCT4, UPP: 1120 indication that upp is good.

regards

bengkel_hp · 03-28-2005, 23:38

if 1st boot ok, it's not 100 % upp in good condition, because upp have many many way to on the phone

VinhHai · 03-29-2005, 10:09

Thank you very much about ur post.

I will try to do it, I 'm too think about UPP but now I don't have new UPP to change. Last time I have changed Flash IC. When finish I will post result.

B.R

aboud · 03-29-2005, 22:30

first check the batt. connectors specialy the middle one try to push it outside a little bit.
second clean the cable connectors on the pcb.
and try it

moblastboy · 03-29-2005, 23:02

i have same problem with my ufs.after sometime experiments i think so the problem is in the conections with the phone.try with another conector.But i'm not sure in 100%.

03-28-2005, 05:02	#1 (permalink)
VinhHai Freak Poster Join Date: Jul 2003 Posts: 363 Member: 34310 Status: Offline Thanks Meter: 23	Help about UFS3 Hi USF team I have just changed UEM and when I flash N6100 and I see: "1st Boot Ok, DCT4, UPP: 1120 2nd Boot Error: 2 Platform: 3, Error Data: E3 72 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 Process Failed, Repowering Mobile" I've rehot Flash IC and UPP but nothing change, when I choose "CHECK" I see nomaly. What 's it mean? Pls help me. Thks

03-29-2005, 10:09	#5 (permalink)
VinhHai Freak Poster Join Date: Jul 2003 Posts: 363 Member: 34310 Status: Offline Thanks Meter: 23	Thks everybody Thank you very much about ur post. I will try to do it, I 'm too think about UPP but now I don't have new UPP to change. Last time I have changed Flash IC. When finish I will post result. B.R

03-29-2005, 23:02	#7 (permalink)
moblastboy Insane Poster Join Date: Feb 2005 Location: Bulgaria Age: 54 Posts: 61 Member: 113146 Status: Offline Thanks Meter: 2	ufs i have same problem with my ufs.after sometime experiments i think so the problem is in the conections with the phone.try with another conector.But i'm not sure in 100%.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
About UFS3 firmware update...	omega_plus	UFS2 + UFS3-Tornadoflasher	8	01-27-2014 15:37
need help about ufs3 tornado	mehdi1978	UFS2 + UFS3-Tornadoflasher	2	09-15-2008 05:38
plz help about ufs3	sushilkumar	UFS2 + UFS3-Tornadoflasher	1	05-24-2008 21:41
PLease Help me About UFS3	onlyrasel	UFS2 + UFS3-Tornadoflasher	1	04-13-2007 08:57
please helping about ufs3	salama10	UFS2 + UFS3-Tornadoflasher	0	04-01-2007 13:42

03-28-2005, 17:55	#2 (permalink)
bengkel_hp Freak Poster Join Date: Jun 2004 Age: 47 Posts: 240 Member: 68021 Status: Offline Thanks Meter: 11	i found the problem too, you can resolved the problem with change upp ic or flash ic.

03-28-2005, 20:19	#3 (permalink)
imam Freak Poster Join Date: Sep 2004 Location: indonesia Age: 47 Posts: 253 Member: 82846 Status: Offline Thanks Meter: 29	i think the flash ic first, because "1st Boot Ok, DCT4, UPP: 1120 indication that upp is good. regards

03-28-2005, 23:38	#4 (permalink)
bengkel_hp Freak Poster Join Date: Jun 2004 Age: 47 Posts: 240 Member: 68021 Status: Offline Thanks Meter: 11	if 1st boot ok, it's not 100 % upp in good condition, because upp have many many way to on the phone

03-29-2005, 22:30	#6 (permalink)
aboud Freak Poster Join Date: Feb 2005 Location: West Africa Age: 48 Posts: 129 Member: 113414 Status: Offline Thanks Meter: 44	first check the batt. connectors specialy the middle one try to push it outside a little bit. second clean the cable connectors on the pcb. and try it