>>How to Repair Dead Nokia 2600<< - GSM-Forum

thoyyu · 06-16-2006, 18:58

Hi Guys,

I am trying to flash a dead nokia 2600 with N-Box....i am having trouble flashing it...i am providing the log from N-Box

1st Boot Ok, DCT4, UPP: 1201
Fl0: 0x01000000-0x01FFFFFF,19E4FA3B,
Algorithm: u_intel.fia, Ver: 4.19.0
Algorithm Ok, MSID: 84218202BA3D7E3FB6AB3842F1
Decoded MSID: 3E4EBAE9-00D3B37C-A9000000
Encoded FAID: 8EEFB07B-B03B8471-F793ACCA
Erasing: 0x01000000-0x0100FFFF ...
Erasing Error: 10, at: 0x01000000-0x0100FFFF, 940207, Time: 00:00
Process Failed, Repowering Mobile

can anyone give me a solution to repair this phone

thanx in advance

emchido · 06-16-2006, 19:31

May be if u continue trying it, hold the set tight, no hand checking, it will flash ok,
Also klick check, after klick flash immediatly.

thoyyu · 06-20-2006, 16:36

Its didnt work do u have any more ideas

transit · 06-20-2006, 20:22

try to heat the panel before flashing pls post result

KHJAMAL · 06-20-2006, 22:42

Try to rehot flash IC

mukasa shuaib · 06-21-2006, 22:45

Quote:

Originally Posted by thoyyu

Hi Guys,

I am trying to flash a dead nokia 2600 with N-Box....i am having trouble flashing it...i am providing the log from N-Box

1st Boot Ok, DCT4, UPP: 1201
Fl0: 0x01000000-0x01FFFFFF,19E4FA3B,
Algorithm: u_intel.fia, Ver: 4.19.0
Algorithm Ok, MSID: 84218202BA3D7E3FB6AB3842F1
Decoded MSID: 3E4EBAE9-00D3B37C-A9000000
Encoded FAID: 8EEFB07B-B03B8471-F793ACCA
Erasing: 0x01000000-0x0100FFFF ...
Erasing Error: 10, at: 0x01000000-0x0100FFFF, 940207, Time: 00:00
Process Failed, Repowering Mobile

can anyone give me a solution to repair this phone

thanx in advance

apply heat with rework station on the flash ic. make sure u dont use soldering paste coz the ic could bend one side.then flash again. or run set up again

Jageer · 06-27-2006, 02:26

Hi,

I am trying to flash a dead nokia 2600 with ufs Box.

Select 2600 --> Erase --> Start Address 01000000 (Default) --> Change the End Address 01FFFFFF to 013FFFFF. Now erase the flash area.

Then write MCU and PPM files. Now Phone OK. (GSM 900 Mhz Signal Error).

Write 1100 PM File 34% only (Do not write full pm file). Remove the tick (Un Select) in Autodetect Product. Select 1100 --> Wr PM --> 1100 pm file --> Stop in 34% . Now phone work with 100% Good Signal.

Use same Method for 3100 & 3120. Thanks.

soybean · 06-27-2006, 06:03

check the crystal 32.768khz...

ayus1111 · 06-28-2006, 05:27

pls i want to repair nokia 2650, kindly help with its shematics diagram

.::Skylinks::. · 06-28-2006, 05:45

Erase your 2600 using 1100 erase file.....Hope it works

klaos · 06-28-2006, 08:48

Quote:

Originally Posted by thoyyu

Hi Guys,

I am trying to flash a dead nokia 2600 with N-Box....i am having trouble flashing it...i am providing the log from N-Box

1st Boot Ok, DCT4, UPP: 1201
Fl0: 0x01000000-0x01FFFFFF,19E4FA3B,
Algorithm: u_intel.fia, Ver: 4.19.0
Algorithm Ok, MSID: 84218202BA3D7E3FB6AB3842F1
Decoded MSID: 3E4EBAE9-00D3B37C-A9000000
Encoded FAID: 8EEFB07B-B03B8471-F793ACCA
Erasing: 0x01000000-0x0100FFFF ...
Erasing Error: 10, at: 0x01000000-0x0100FFFF, 940207, Time: 00:00
Process Failed, Repowering Mobile

can anyone give me a solution to repair this phone

thanx in advance

i had the same problem. i tryed to rehot the flash is, but dont` work. i changed the upp ic, and now it`s work fine. try it

rajiv007 · 06-28-2006, 10:32

i think its a flash IC problem try to use normal heat to flash IC then check

.:AnOuaR:. · 06-30-2006, 00:35

1st Boot Ok, DCT4, UPP: 1201
Fl0: 0x01000000-0x01FFFFFF,87CDB60A,
Algorithm: u_intel.fia, Ver: 4.44.1
Algorithm Ok, MSID: 84A581166551D78216923EB542
Decoded MSID: 3E4EBAE9-005578A7-A8000000
Encoded FAID: 29C3B644-407D871C-6853E855
Erasing: 0x011FC000-0x011FFFFF ...
Erasing Error: 10, at: 0x011FC000-0x011FFFFF, 940207, Time: 00:00
Process Failed, Repowering Mobile

same problem in 2600 are there solution ???

thoyyu · 08-17-2006, 14:13

Quote:

Originally Posted by Jageer

Hi,

I am trying to flash a dead nokia 2600 with ufs Box.

Select 2600 --> Erase --> Start Address 01000000 (Default) --> Change the End Address 01FFFFFF to 013FFFFF. Now erase the flash area.

Then write MCU and PPM files. Now Phone OK. (GSM 900 Mhz Signal Error).

Write 1100 PM File 34% only (Do not write full pm file). Remove the tick (Un Select) in Autodetect Product. Select 1100 --> Wr PM --> 1100 pm file --> Stop in 34% . Now phone work with 100% Good Signal.

Use same Method for 3100 & 3120. Thanks.

Hi,

I tried ur method but i cudnt flash the MCU & PPM it give me the same error message...i did erase using the addresses u provided me .

can u tell me how i can flash it

thanx in advance

sunsco · 08-17-2006, 21:22

Thank Uuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuu For This.

06-16-2006, 18:58	#1 (permalink)
thoyyu Insane Poster Join Date: Apr 2006 Location: Male', Maldives Posts: 99 Member: 260672 Status: Offline Thanks Meter: 20	>>How to Repair Dead Nokia 2600<< Hi Guys, I am trying to flash a dead nokia 2600 with N-Box....i am having trouble flashing it...i am providing the log from N-Box 1st Boot Ok, DCT4, UPP: 1201 Fl0: 0x01000000-0x01FFFFFF,19E4FA3B, Algorithm: u_intel.fia, Ver: 4.19.0 Algorithm Ok, MSID: 84218202BA3D7E3FB6AB3842F1 Decoded MSID: 3E4EBAE9-00D3B37C-A9000000 Encoded FAID: 8EEFB07B-B03B8471-F793ACCA Erasing: 0x01000000-0x0100FFFF ... Erasing Error: 10, at: 0x01000000-0x0100FFFF, 940207, Time: 00:00 Process Failed, Repowering Mobile can anyone give me a solution to repair this phone thanx in advance

06-27-2006, 02:26	#7 (permalink)
Jageer Junior Member Join Date: Jun 2006 Posts: 4 Member: 300907 Status: Offline Thanks Meter: 2	2600 Erashing Error Solution. Hi, I am trying to flash a dead nokia 2600 with ufs Box. Select 2600 --> Erase --> Start Address 01000000 (Default) --> Change the End Address 01FFFFFF to 013FFFFF. Now erase the flash area. Then write MCU and PPM files. Now Phone OK. (GSM 900 Mhz Signal Error). Write 1100 PM File 34% only (Do not write full pm file). Remove the tick (Un Select) in Autodetect Product. Select 1100 --> Wr PM --> 1100 pm file --> Stop in 34% . Now phone work with 100% Good Signal. Use same Method for 3100 & 3120. Thanks.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
How To Repair Dead Nokia 1100	celluniversal	Nokia Digital Core Technology 4 ( DCT-4 )	10	11-26-2012 16:09
how to repair dead nokia n70	shakil143	Nokia Hardware & Hardware Repair	2	10-24-2009 01:27
how to repair dead nokia 1650	patelfaizu	Nokia Hardware & Hardware Repair	2	07-15-2009 19:28
How To Repair Dead Nokia 1100	celluniversal	Nokia Digital Core Technology 4 ( DCT-4 )	5	09-25-2007 13:32
>>How to flash dead nokia 7610 with n-box<<	thoyyu	n-Box	3	06-22-2006 21:52

06-16-2006, 19:31	#2 (permalink)
emchido Freak Poster Join Date: Aug 2005 Age: 47 Posts: 152 Member: 171593 Status: Offline Thanks Meter: 13	May be if u continue trying it, hold the set tight, no hand checking, it will flash ok, Also klick check, after klick flash immediatly.

06-20-2006, 16:36	#3 (permalink)
thoyyu Insane Poster Join Date: Apr 2006 Location: Male', Maldives Posts: 99 Member: 260672 Status: Offline Thanks Meter: 20	Its didnt work do u have any more ideas

06-20-2006, 20:22	#4 (permalink)
transit Freak Poster Join Date: Jun 2004 Location: abuja nigeria Posts: 113 Member: 70830 Status: Offline Thanks Meter: 1	try to heat the panel before flashing pls post result

06-20-2006, 22:42	#5 (permalink)
KHJAMAL Registered User Join Date: May 2005 Location: My Office Posts: 1,009 Member: 143939 Status: Offline Thanks Meter: 264	Try to rehot flash IC

06-27-2006, 06:03	#8 (permalink)
soybean Freak Poster Join Date: Aug 2004 Posts: 498 Member: 77254 Status: Offline Thanks Meter: 9	check the crystal 32.768khz...

06-28-2006, 05:27	#9 (permalink)
ayus1111 Junior Member Join Date: Jun 2006 Posts: 1 Member: 301810 Status: Offline Thanks Meter: 0	pls i want to repair nokia 2650, kindly help with its shematics diagram

06-28-2006, 05:45	#10 (permalink)
.::Skylinks::. No Life Poster Join Date: Jun 2006 Location: Pakistan Age: 36 Posts: 1,911 Member: 300354 Status: Offline Sonork: 100.1577485 Thanks Meter: 760	Erase your 2600 using 1100 erase file.....Hope it works

06-28-2006, 10:32	#12 (permalink)
rajiv007 No Life Poster Join Date: Aug 2004 Age: 51 Posts: 1,064 Member: 78767 Status: Offline Sonork: 100.95137 Thanks Meter: 566	i think its a flash IC problem try to use normal heat to flash IC then check

06-30-2006, 00:35	#13 (permalink)
.:AnOuaR:. No Life Poster Join Date: Apr 2004 Location: london, united kingdom Age: 42 Posts: 518 Member: 62602 Status: Offline Thanks Meter: 6	1st Boot Ok, DCT4, UPP: 1201 Fl0: 0x01000000-0x01FFFFFF,87CDB60A, Algorithm: u_intel.fia, Ver: 4.44.1 Algorithm Ok, MSID: 84A581166551D78216923EB542 Decoded MSID: 3E4EBAE9-005578A7-A8000000 Encoded FAID: 29C3B644-407D871C-6853E855 Erasing: 0x011FC000-0x011FFFFF ... Erasing Error: 10, at: 0x011FC000-0x011FFFFF, 940207, Time: 00:00 Process Failed, Repowering Mobile same problem in 2600 are there solution ???

08-17-2006, 21:22	#15 (permalink)
sunsco Freak Poster Join Date: Jan 2006 Location: Nigeria Posts: 288 Member: 216438 Status: Offline Sonork: 160962 Thanks Meter: 31	Thank Uuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuu For This.