n 3120 test mode - GSM-Forum

xgen_vaibhav · 11-04-2006, 18:36

i have done full flash . but still there is [pro.

cdmababa · 11-04-2006, 19:49

Quote:

Originally Posted by xgen_vaibhav

i have done full flash . but still there is [pro.

try it ,ithink it work 4 u

gsm_surya · 04-28-2007, 17:24

i tried it is not working. please give me another soln.

Allunlockingsource · 04-29-2007, 12:27

Try to software maybe your problem is solve ok .....................

GsmGalant · 05-02-2007, 18:55

Any solution for 6610 in test mode ?

sree krishna · 05-03-2007, 05:36

Quote:

Originally Posted by GsmGalant

Any solution for 6610 in test mode ?

6610, 7210, local mode, test mode, not charging solution

shritelmob · 05-03-2007, 06:47

U have to flash set,if same problem remove resistors from BSI of battery connection ,Your set is water damages simply **** UEM also.

That'sme · 05-03-2007, 09:16

Heat the UEM and check the BSI line components.

vilas_vanjari · 05-03-2007, 10:39

Hi,
1> if test mode appears on the LCD immediatly when you insert battry then check BSI line from batt connector till UEM search for any Capacitor or register is short with Gnd (remove if cap & replace if Reg)

2> if test mode appears on the LCD when you press on/off switch then just short BSI point off batt connector to Gnd directly with jumper wire or you can put a register.

hope you will get rid of Test Mode

BR,
Vilas

GsmGalant · 05-03-2007, 12:22

Thanks to all but problem still not solwed. When press on/off switch, then show "test mode". Flashing by same vers, full reset, remove C100, short BSI point off batt connector to Gnd, but same result. Only from UFS3 could be enter in normal mode, thereafter when put batery again show "test mode"

vilas_vanjari · 05-03-2007, 12:42

Quote:

Originally Posted by GsmGalant

Thanks to all but problem still not solwed. When press on/off switch, then show "test mode". Flashing by same vers, full reset, remove C100, short BSI point off batt connector to Gnd, but same result. Only from UFS3 could be enter in normal mode, thereafter when put batery again show "test mode"

Hi,
I am very sorry this dosnt help you.
try following which i have tried
if you have any UEM replace erlier b'cause of ????? and you have kept it with you or any new UEM

replace the UEM with your phones UEM

dont worry dont write RPL file it is a mejor test that if your phone can get swiched on in normal mode "insert Sim card" on display if YES then this is the result ( Need to Change Uem)

if not then yr phones PCB might be damaged (short) internally

i have tried this with live phone and again put its old UEM back and no ????

The best way to be prepared for the FUTURE is to INVENT it... Think Win Win all the way

BR,
Vilas

vilas_vanjari · 05-03-2007, 12:46

Hi,

Even Damaged or ???? live Uem can help us Finding some serious faults alwas keep them for R & D.

BR,
Vilas

GsmGalant · 05-05-2007, 09:10

Thank you Vilas so should it be but how is payable when complete phone cost less of 30 Eur?
B. R.

vilas_vanjari · 05-05-2007, 09:26

Quote:

Originally Posted by GsmGalant

Thank you Vilas so should it be but how is payable when complete phone cost less of 30 Eur?
B. R.

Hi,
I didnt get what you want to say"

BR,
Vilas

GsmGalant · 05-06-2007, 05:41

Hello Vilas,
What ever do you mean? Is it payable to change MCU in 6610, if complete phone cost is 30 eur. How much to be paid customer ?

For me not is payable

sorry for my english.

11-04-2006, 18:36	#1 (permalink)
xgen_vaibhav Junior Member Join Date: Jan 2006 Posts: 18 Member: 224667 Status: Offline Thanks Meter: 0	n 3120 test mode i have done full flash . but still there is [pro.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
3120 test mode....	acelai00	Nokia Hardware & Hardware Repair	11	11-01-2012 10:13
3120 test mode....	abrarmultani	Nokia Hardware & Hardware Repair	2	04-10-2008 13:53
3120 test mode....	abrarmultani	Nokia Hardware & Hardware Repair	0	04-10-2008 10:58
3120 test mode	naseer_10_1980	Nokia Digital Core Technology 4 ( DCT-4 )	3	02-05-2007 03:00
n 3120 test mode	xgen_vaibhav	Nokia Hardware & Hardware Repair	1	11-04-2006 20:52

04-28-2007, 17:24	#3 (permalink)
gsm_surya Freak Poster Join Date: Dec 2005 Location: Chennai, Tamilnadu, India Posts: 232 Member: 205776 Status: Offline Thanks Meter: 53	i tried it is not working. please give me another soln.

04-29-2007, 12:27	#4 (permalink)
Allunlockingsource No Life Poster Join Date: Aug 2006 Location: SPAIN-----UK Posts: 2,037 Member: 333439 Status: Offline Sonork: 100.1589101 Thanks Meter: 623	Try to software maybe your problem is solve ok .....................

05-02-2007, 18:55	#5 (permalink)
GsmGalant No Life Poster Join Date: Oct 2004 Location: Kosova Posts: 919 Member: 87568 Status: Offline Thanks Meter: 101	Any solution for 6610 in test mode ?

05-03-2007, 06:47	#7 (permalink)
shritelmob Freak Poster Join Date: Sep 2006 Location: INDIA Age: 48 Posts: 162 Member: 350948 Status: Offline Thanks Meter: 32	U have to flash set,if same problem remove resistors from BSI of battery connection ,Your set is water damages simply **** UEM also.

05-03-2007, 09:16	#8 (permalink)
That'sme Freak Poster Join Date: Feb 2006 Location: Inside Boxes Posts: 303 Member: 228871 Status: Offline Thanks Meter: 43	Heat the UEM and check the BSI line components.

05-03-2007, 10:39	#9 (permalink)
vilas_vanjari Freak Poster Join Date: Jan 2006 Location: India Posts: 134 Member: 222373 Status: Offline Thanks Meter: 9	Hi, 1> if test mode appears on the LCD immediatly when you insert battry then check BSI line from batt connector till UEM search for any Capacitor or register is short with Gnd (remove if cap & replace if Reg) 2> if test mode appears on the LCD when you press on/off switch then just short BSI point off batt connector to Gnd directly with jumper wire or you can put a register. hope you will get rid of Test Mode BR, Vilas

05-03-2007, 12:22	#10 (permalink)
GsmGalant No Life Poster Join Date: Oct 2004 Location: Kosova Posts: 919 Member: 87568 Status: Offline Thanks Meter: 101	Thanks to all but problem still not solwed. When press on/off switch, then show "test mode". Flashing by same vers, full reset, remove C100, short BSI point off batt connector to Gnd, but same result. Only from UFS3 could be enter in normal mode, thereafter when put batery again show "test mode"

05-03-2007, 12:46	#12 (permalink)
vilas_vanjari Freak Poster Join Date: Jan 2006 Location: India Posts: 134 Member: 222373 Status: Offline Thanks Meter: 9	Hi, Even Damaged or ???? live Uem can help us Finding some serious faults alwas keep them for R & D. BR, Vilas

05-05-2007, 09:10	#13 (permalink)
GsmGalant No Life Poster Join Date: Oct 2004 Location: Kosova Posts: 919 Member: 87568 Status: Offline Thanks Meter: 101	Thank you Vilas so should it be but how is payable when complete phone cost less of 30 Eur? B. R.

05-06-2007, 05:41	#15 (permalink)
GsmGalant No Life Poster Join Date: Oct 2004 Location: Kosova Posts: 919 Member: 87568 Status: Offline Thanks Meter: 101	Hello Vilas, What ever do you mean? Is it payable to change MCU in 6610, if complete phone cost is 30 eur. How much to be paid customer ? For me not is payable sorry for my english.