NOKIA 6610, 7210, 7250 FLASHING ok.. Don't power on. - GSM-Forum

DrMobile · 03-06-2004, 12:19

I have NOKIA phones MODEL 6610, 7210, 7250.. ALL are flashing ok.. Flashed with diffrent flashers... erased full FLASH but I don't able to power on it with flasher.

any one post here their experince regarding repairing above problem.

Best Regards,
Wahab

Platijet · 03-06-2004, 20:43

run BBTESTS (function supported in griffin box) and check results.

also:at the end of flashing factory set is ok?

choose for ppm the mcu flashfile and after this flash with normal mcu and ppm

MAJESTIC PIRATE · 03-06-2004, 23:33

just clean your pcb , rehot it slowly and take care about its ram , then reflash it again using griffin box .........

eivoig · 03-07-2004, 14:09

just try to check if you flash it correctly, try to use the test box,or else falsh it again,using the software you use.use griffin,.

eivoig · 03-07-2004, 14:10

try to use prodigy also if itwill answer your problem

isaackenny · 03-07-2004, 15:16

i had few set of 7250 most common is Flash Ic or UPP Faulty .

03-06-2004, 12:19	#1 (permalink)
DrMobile No Life Poster Join Date: Aug 2001 Location: P A K I S T A N _____________ Age: 40 Posts: 3,579 Member: 5932 Status: Offline Thanks Meter: 1,694	NOKIA 6610, 7210, 7250 FLASHING ok.. Don't power on. I have NOKIA phones MODEL 6610, 7210, 7250.. ALL are flashing ok.. Flashed with diffrent flashers... erased full FLASH but I don't able to power on it with flasher. any one post here their experince regarding repairing above problem. Best Regards, Wahab

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Solutions for Nokia 6610-7210-7250	samirov-gsm	Nokia Hardware & Hardware Repair	0	07-03-2009 08:58
n70 charging ok don't power on	sianmobile	Nokia Hardware & Hardware Repair	9	01-16-2007 17:57
Nokia 6610 with 7250 flash IC -please comment...	Rolf2	Nokia Hardware & Hardware Repair	0	07-04-2004 14:29
PANA GD67 flashing ok. Can't power ON.	DrMobile	Panasonic	18	11-10-2003 12:12

03-06-2004, 20:43	#2 (permalink)
Platijet No Life Poster Join Date: Apr 2003 Location: Greece Age: 47 Posts: 3,358 Member: 26279 Status: Offline Thanks Meter: 274	run BBTESTS (function supported in griffin box) and check results. also:at the end of flashing factory set is ok? choose for ppm the mcu flashfile and after this flash with normal mcu and ppm

03-06-2004, 23:33	#3 (permalink)
MAJESTIC PIRATE Freak Poster Join Date: Dec 2003 Location: E G Y P T Age: 47 Posts: 336 Member: 45635 Status: Offline Thanks Meter: 20	just clean your pcb , rehot it slowly and take care about its ram , then reflash it again using griffin box .........

03-07-2004, 14:09	#4 (permalink)
eivoig No Life Poster Join Date: Jul 2001 Location: Spinning on my OWN Orbit Posts: 968 Member: 5358 Status: Offline Thanks Meter: 211	just try to check if you flash it correctly, try to use the test box,or else falsh it again,using the software you use.use griffin,.

03-07-2004, 14:10	#5 (permalink)
eivoig No Life Poster Join Date: Jul 2001 Location: Spinning on my OWN Orbit Posts: 968 Member: 5358 Status: Offline Thanks Meter: 211	try to use prodigy also if itwill answer your problem

03-07-2004, 15:16	#6 (permalink)
isaackenny Freak Poster Join Date: Feb 2002 Location: singapore Age: 46 Posts: 404 Member: 9194 Status: Offline Thanks Meter: 3	i had few set of 7250 most common is Flash Ic or UPP Faulty .